RE: Serial interface error.

Please find the "Show controllers serial 1/3"

M4T: show controller:
PAS unit 3, subunit 3, f/w version 1-45, rev ID 0x2800001, version 3
idb = 0x6256E6E4, ds = 0x625704EC, ssb=0x625708A0
Clock mux=0x0, ucmd_ctrl=0xC, port_status=0x74
Serial config=0x8, line config=0x200
maxdgram=1608, bufpool=78Kb, 120 particles
     DCD=up DSR=up DTR=up RTS=up CTS=up
line state: up
cable type : V.35 DTE cable, received clockrate 255840

base0 registers=0x3D000000, base1 registers=0x3D002000
mxt_ds=0x626EF858, rx ring entries=78, tx ring entries=128
rxring=0x3B6CE20, rxr shadow=0x62576E94, rx_head=0
txring=0x3B6D0C0, txr shadow=0x62577268, tx_head=34, tx_tail=34, tx_count=0
throttled=0, enabled=0
halted=0, last halt reason=0
Microcode fatal errors=0
rx_no_eop_err=0, rx_no_stp_err=0, rx_no_eop_stp_err=0
rx_no_buf=0, rx_soft_overrun_err=0, dump_err= 0, bogus=0, mxt_flags=0x0
tx_underrun_err=1, tx_soft_underrun_err=1, tx_limited=1(2)
tx_fullring=13147591, tx_started=17925099 mxt_flush_count=0
rx_int_count=34348762, tx_int_count=31081383

Best Regards,

==============================
Mahmoud Nossair

-----Original Message-----
From: rdarsey_at_gmail.com [mailto:rdarsey_at_gmail.com]
Sent: Saturday, May 15, 2010 8:49 PM
To: Mahmoud Nossair; ccielab_at_groupstudy.com
Subject: Re: Serial interface error.

What does a "show controllers" show? Any slips? If so clocking may be an
issue. Verify that clock is either provided by the ISP or in the case of a
point to point circuit that one side is set to clock source internal and one
is set to clock source line.

Rick
-----Original Message-----
From: "Mahmoud Nossair" <mahmoud.nossair_at_gmail.com>
Date: Sat, 15 May 2010 19:24:31
To: <ccielab_at_groupstudy.com>
Subject: Serial interface error.

Dear Experts

We have some branches connecting to the Head Quarter through a telecom
company, when I running "show interface serial 1/3" I found there are many
errors,

I know that there is an errors on the fastethetnet interfaces happens from
collisions duplex mismatch, but I am wondering what is the kind of the
errors will be occurred on the serial interfaces .

There is one thing also , we never reach the maximum bandwidth, although we
are suffering from a congestion.

Here is show interface output:

======================================

Serial1/3 is up, line protocol is up

  Hardware is M4T

  Internet address is x.x.x.x/30

  MTU 1500 bytes, BW 2000 Kbit, DLY 20000 usec,

     reliability 255/255, txload 21/255, rxload 16/255

  Encapsulation HDLC, crc 16, loopback not set

  Keepalive set (10 sec)

  Restart-Delay is 0 secs

  Last input 00:00:00, output 00:00:00, output hang never

  Last clearing of "show interface" counters never

  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
1154031

  Queueing strategy: weighted fair

  Output queue: 0/1000/64/1154031 (size/max total/threshold/drops)

     Conversations 0/36/256 (active/max active/max total)

     Reserved Conversations 0/0 (allocated/max allocated)

     Available Bandwidth 1900 kilobits/sec

  30 second input rate 133000 bits/sec, 245 packets/sec

  30 second output rate 165000 bits/sec, 134 packets/sec

     31407760 packets input, 2687152838 bytes, 0 no buffer

     Received 41308 broadcasts, 0 runts, 0 giants, 0 throttles

     27636 input errors, 27635 CRC, 0 frame, 1 overrun, 0 ignored, 0 abort

     16397297 packets output, 3885690293 bytes, 1 underruns

     1 output errors, 0 collisions, 3 interface resets

     0 output buffer failures, 0 output buffers swapped out

     4 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up

==============================================================

Please any help regarding this issue.

Thanks in advance.

Best Regards,

Mahmoud Nossair

Blogs and organic groups at http://www.ccie.net
Received on Sat May 15 2010 - 20:56:28 ART