Re: FR-VLAN Interworking not working

While working on this, I thought of something else to add. Is it possible to
add these links to be part of a certain VRF? Just a thought....

On Wed, Jan 13, 2010 at 10:24 PM, Bryan Bartik <bbartik_at_ipexpert.com> wrote:

> Hehe. Sweet!
>
>
> On Wed, Jan 13, 2010 at 12:39 PM, Service Provider <
> service.providersa_at_gmail.com> wrote:
>
>> Super stuff!! Works on 12.2(25)S15
>>
>>
>> On Wed, Jan 13, 2010 at 7:57 PM, Bryan Bartik <bbartik_at_ipexpert.com>wrote:
>>
>>> I just loaded the same lab on 12.0 and it doesn't work. The VC comes up
>>> after awhile but no traffic passes. I should have been aware of the
>>> bug/unsupported version! However, the lab does test on 12.2S so I would
>>> stick with that code during your prep, especially with issues like this :)
>>> Let me know if you have issues with 12.2S.
>>>
>>>
>>> On Wed, Jan 13, 2010 at 10:47 AM, Bryan Bartik <bbartik_at_ipexpert.com>wrote:
>>>
>>>> Hi, could be a bug :/ Definitely not a surprise on the SP track. Or
>>>> maybe not supported in that version. Let me try with 12.0 code. Give me a
>>>> few minutes and I will post back.
>>>>
>>>>
>>>> On Wed, Jan 13, 2010 at 9:59 AM, Service Provider <
>>>> service.providersa_at_gmail.com> wrote:
>>>>
>>>>> Hi Bryan
>>>>>
>>>>> Tx for the assistance.
>>>>>
>>>>> I've rebuilt the scenario and still no luck. What IOS are you using?
>>>>> I'm using Version 12.0(33)S3.
>>>>>
>>>>> Everything looks fine except my ping fails. This is frustrating as I've
>>>>> spent A LOT of time trying to get this to work. :(
>>>>>
>>>>> PE2(config-if)#do sh mpls l2 v de
>>>>> Local interface: Fa2/0 up, line protocol up, Ethernet up
>>>>> Destination address: 1.1.1.1, VC ID: 100, VC status: up
>>>>>
>>>>> Preferred path: not configured
>>>>> Default path: active
>>>>> Next hop: point2point
>>>>> Output interface: Se1/0, imposed label stack {33}
>>>>> Create time: 00:07:29, last status change time: 00:06:06
>>>>> Signaling protocol: LDP, peer 1.1.1.1:0 up
>>>>> Targeted Hello: 2.2.2.2(LDP Id) -> 1.1.1.1
>>>>> MPLS VC labels: local 33, remote 33
>>>>>
>>>>> Group ID: local 0, remote 0
>>>>> MTU: local 1500, remote 1500
>>>>> Remote interface description:
>>>>> Sequencing: receive disabled, send disabled
>>>>> VC statistics:
>>>>> packet totals: receive 132, send 58
>>>>> byte totals: receive 8080, send 7994
>>>>>
>>>>> packet drops: receive 0, seq error 0, send 0
>>>>>
>>>>> E2(config-if)#do sh mpls ldp ne
>>>>> Peer LDP Ident: 1.1.1.1:0; Local LDP Ident 2.2.2.2:0
>>>>> TCP connection: 1.1.1.1.646 - 2.2.2.2.55744
>>>>> State: Oper; Msgs sent/rcvd: 19/19; Downstream
>>>>> Up time: 00:10:59
>>>>> LDP discovery sources:
>>>>> Serial1/0, Src IP addr: 150.1.12.1
>>>>> Targeted Hello 2.2.2.2 -> 1.1.1.1, active, passive
>>>>>
>>>>> Addresses bound to peer LDP Ident:
>>>>> 150.1.12.1 1.1.1.1
>>>>>
>>>>> PE1(config-if)#do sh mpl l2 v d
>>>>> Local interface: Se1/0 up, line protocol up, FR DLCI 102 up
>>>>>
>>>>> MPLS VC type is FR DLCI, interworking type is Ethernet
>>>>> Destination address: 2.2.2.2, VC ID: 100, VC status: up
>>>>> Preferred path: not configured
>>>>> Default path: active
>>>>> Next hop: point2point
>>>>> Output interface: Se1/1, imposed label stack {33}
>>>>> Create time: 00:09:09, last status change time: 00:06:34
>>>>>
>>>>> Signaling protocol: LDP, peer 2.2.2.2:0 up
>>>>> Targeted Hello: 1.1.1.1(LDP Id) -> 2.2.2.2
>>>>> MPLS VC labels: local 33, remote 33
>>>>>
>>>>> Group ID: local 0, remote 0
>>>>> MTU: local 1500, remote 1500
>>>>> Remote interface description:
>>>>> Sequencing: receive disabled, send disabled
>>>>> VC statistics:
>>>>> packet totals: receive 61, send 146
>>>>> byte totals: receive 8198, send 8920
>>>>>
>>>>> packet drops: receive 0, seq error 0, send 0
>>>>>
>>>>> PE1(config-if)#do sh mpls ldp ne
>>>>> Peer LDP Ident: 2.2.2.2:0; Local LDP Ident 1.1.1.1:0
>>>>> TCP connection: 2.2.2.2.55744 - 1.1.1.1.646
>>>>> State: Oper; Msgs sent/rcvd: 18/19; Downstream
>>>>> Up time: 00:10:28
>>>>>
>>>>> LDP discovery sources:
>>>>> Serial1/1, Src IP addr: 150.1.12.2
>>>>> Targeted Hello 1.1.1.1 -> 2.2.2.2, active, passive
>>>>>
>>>>> Addresses bound to peer LDP Ident:
>>>>> 2.2.2.2 150.1.12.2
>>>>>
>>>>>
>>>>>
>>>>> On Wed, Jan 13, 2010 at 5:29 PM, Bryan Bartik <bbartik_at_ipexpert.com>wrote:
>>>>>
>>>>>> No, bridging does work. I am using your .net file. See below:
>>>>>>
>>>>>> CE1----Frame Switch----PE1----PE2----CE2
>>>>>>
>>>>>> CE1:
>>>>>>
>>>>>> bridge irb
>>>>>>
>>>>>> bridge 1 protocol ieee
>>>>>> bridge 1 route ip
>>>>>>
>>>>>> interface Serial1/0
>>>>>> no ip address
>>>>>> encapsulation frame-relay
>>>>>>
>>>>>> frame-relay map bridge 101 broadcast
>>>>>>
>>>>>> interface BVI1
>>>>>> ip address 10.10.10.1 255.255.255.0
>>>>>> no clns route-cache
>>>>>>
>>>>>> PE1:
>>>>>>
>>>>>>
>>>>>> pseudowire-class INTERWORKING
>>>>>> encapsulation mpls
>>>>>> interworking ethernet
>>>>>>
>>>>>> interface Serial1/0
>>>>>> no ip address
>>>>>> encapsulation frame-relay
>>>>>>
>>>>>>
>>>>>> connect FR-VLAN-IW Serial1/0 101 l2transport
>>>>>> xconnect 2.2.2.2 100 pw-class INTERWORKING
>>>>>>
>>>>>> PE2:
>>>>>>
>>>>>>
>>>>>> pseudowire-class l2inter
>>>>>> encapsulation mpls
>>>>>> interworking ethernet
>>>>>>
>>>>>> interface FastEthernet2/0.100
>>>>>> encapsulation dot1Q 100
>>>>>> no cdp enable
>>>>>>
>>>>>> xconnect 1.1.1.1 100 pw-class l2inter
>>>>>>
>>>>>> CE2:
>>>>>>
>>>>>>
>>>>>> interface FastEthernet1/0.100
>>>>>> encapsulation dot1Q 100
>>>>>> ip address 10.10.10.2 255.255.255.0
>>>>>>
>>>>>> Verification:
>>>>>>
>>>>>> PE1#show mpl l2transport vc de
>>>>>>
>>>>>> Local interface: Se1/0 up, line protocol up, FR DLCI 101 up
>>>>>> MPLS VC type is Ethernet, interworking type is Ethernet <----
>>>>>> Bridged
>>>>>>
>>>>>> Destination address: 2.2.2.2, VC ID: 100, VC status: up
>>>>>> Output interface: Se1/1, imposed label stack {16}
>>>>>>
>>>>>> Preferred path: not configured
>>>>>> Default path: active
>>>>>> Tunnel label: imp-null, next hop point2point
>>>>>> Create time: 00:02:50, last status change time: 00:01:41
>>>>>> Signaling protocol: LDP, peer 2.2.2.2:0 up
>>>>>> MPLS VC labels: local 17, remote 16
>>>>>> Group ID: local 0, remote 0
>>>>>> MTU: local 1500, remote 1500
>>>>>> Remote interface description:
>>>>>> Sequencing: receive disabled, send disabled
>>>>>> VC statistics:
>>>>>> packet totals: receive 0, send 29
>>>>>> byte totals: receive 0, send 1856
>>>>>> packet drops: receive 0, send 0
>>>>>>
>>>>>> CE1#ping 10.10.10.2
>>>>>>
>>>>>> Type escape sequence to abort.
>>>>>> Sending 5, 100-byte ICMP Echos to 10.10.10.2, timeout is 2 seconds:
>>>>>> .!!!!
>>>>>> Success rate is 80 percent (4/5), round-trip min/avg/max = 20/43/68 ms
>>>>>> CE1#
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> On Tue, Jan 12, 2010 at 10:12 PM, Service Provider <
>>>>>> service.providersa_at_gmail.com> wrote:
>>>>>>
>>>>>>> HI guys,
>>>>>>>
>>>>>>> I've verified all that and unfortunately bridging does not work. I
>>>>>>> have
>>>>>>> converted this to routed and it's working fine. No bridging on CE1
>>>>>>> and the 2
>>>>>>> PEs are interworking IP.
>>>>>>>
>>>>>>> On Wed, Jan 13, 2010 at 6:11 AM, Satinder Singh <
>>>>>>> satinder.iitd_at_gmail.com>wrote:
>>>>>>>
>>>>>>> > Hi Service provider,
>>>>>>> >
>>>>>>> > To me some configuration missing/inconsistency look on the PE
>>>>>>> router and
>>>>>>> > CE1 router.
>>>>>>> >
>>>>>>> > Few of them are.
>>>>>>> >
>>>>>>> > One the CE1 i am not able to find the interface with address
>>>>>>> 10.1.12.1/24
>>>>>>> > so to which interface address you are pinging from CE2... pls
>>>>>>> clarify the
>>>>>>> > same.
>>>>>>> >
>>>>>>> > On the PE1 and PE2 in pseudowire class remove the " interworking
>>>>>>> ethernet"
>>>>>>> > and add " interworking ip" for interworking to work.
>>>>>>> >
>>>>>>> > In addition it is recoomended to add "ip local interfac address
>>>>>>> <address>"
>>>>>>> > in the pseudowire class.
>>>>>>> >
>>>>>>> > Pls check and let me know if it is working.
>>>>>>> >
>>>>>>> > Thanks
>>>>>>> > Satinder
>>>>>>> >
>>>>>>> > On Wed, Jan 13, 2010 at 12:37 AM, Service Provider <
>>>>>>> > service.providersa_at_gmail.com> wrote:
>>>>>>> >
>>>>>>> >> Hi all
>>>>>>> >>
>>>>>>> >> I have setup FR-VLAN Interworking and my l2 tunnel is up but
>>>>>>> cannot ping
>>>>>>> >> between CE sites.
>>>>>>> >>
>>>>>>> >>
>>>>>>> >>
>>>>>>> CE1-----FRSW-------PE1-----------------PE2---------------------VLAN100--------------------CE2
>>>>>>> >>
>>>>>>> >> Configs below, please help....tx.
>>>>>>> >>
>>>>>>> >> CE1#
>>>>>>> >> CE1#sh run
>>>>>>> >> Building configuration...
>>>>>>> >>
>>>>>>> >> Current configuration : 1912 bytes
>>>>>>> >> !
>>>>>>> >> version 12.0
>>>>>>> >> service timestamps debug uptime
>>>>>>> >> service timestamps log uptime
>>>>>>> >> no service password-encryption
>>>>>>> >> !
>>>>>>> >> hostname CE1
>>>>>>> >> !
>>>>>>> >> boot-start-marker
>>>>>>> >> boot-end-marker
>>>>>>> >> !
>>>>>>> >> enable password cisco
>>>>>>> >> !
>>>>>>> >> ip subnet-zero
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> ip cef
>>>>>>> >> no ip domain-lookup
>>>>>>> >> ip ssh time-out 120
>>>>>>> >> ip ssh authentication-retries 3
>>>>>>> >> no mpls traffic-eng auto-bw timers frequency 0
>>>>>>> >> bridge irb
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> interface FastEthernet0/0
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/0
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> encapsulation frame-relay
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> frame-relay map bridge 101 broadcast
>>>>>>> >> frame-relay map bridge 100 broadcast
>>>>>>> >> no frame-relay inverse-arp
>>>>>>> >> bridge-group 1
>>>>>>> >> !
>>>>>>> >> interface Serial1/1
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/2
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/3
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/4
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/5
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/6
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/7
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface BVI1
>>>>>>> >> ip address 10.10.10.1 255.255.255.0
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> ip classless
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> control-plane
>>>>>>> >> !
>>>>>>> >> bridge 1 protocol ieee
>>>>>>> >> bridge 1 route ip
>>>>>>> >> !
>>>>>>> >> line con 0
>>>>>>> >> exec-timeout 0 0
>>>>>>> >> privilege level 15
>>>>>>> >> logging synchronous
>>>>>>> >> stopbits 1
>>>>>>> >> line aux 0
>>>>>>> >> exec-timeout 0 0
>>>>>>> >> privilege level 15
>>>>>>> >> stopbits 1
>>>>>>> >> line vty 0 4
>>>>>>> >> password cisco
>>>>>>> >> login
>>>>>>> >> !
>>>>>>> >> no cns aaa enable
>>>>>>> >> end
>>>>>>> >>
>>>>>>> >>
>>>>>>> >> ce2#
>>>>>>> >> ce2#sh run
>>>>>>> >> Building configuration...
>>>>>>> >>
>>>>>>> >> Current configuration : 810 bytes
>>>>>>> >> !
>>>>>>> >> version 12.0
>>>>>>> >> service timestamps debug uptime
>>>>>>> >> service timestamps log uptime
>>>>>>> >> no service password-encryption
>>>>>>> >> !
>>>>>>> >> hostname ce2
>>>>>>> >> !
>>>>>>> >> boot-start-marker
>>>>>>> >> boot-end-marker
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> ip subnet-zero
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> ip cef
>>>>>>> >> ip ssh time-out 120
>>>>>>> >> ip ssh authentication-retries 3
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> interface FastEthernet0/0
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> !
>>>>>>> >> interface FastEthernet1/0
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> duplex half
>>>>>>> >> speed auto
>>>>>>> >> !
>>>>>>> >> interface FastEthernet1/0.100
>>>>>>> >> encapsulation dot1Q 100
>>>>>>> >> ip address 10.1.12.2 255.255.255.0
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> !
>>>>>>> >> interface FastEthernet1/1
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> duplex half
>>>>>>> >> speed auto
>>>>>>> >> !
>>>>>>> >> ip classless
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> control-plane
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> line con 0
>>>>>>> >> exec-timeout 0 0
>>>>>>> >> logging synchronous
>>>>>>> >> stopbits 1
>>>>>>> >> line aux 0
>>>>>>> >> stopbits 1
>>>>>>> >> line vty 0 4
>>>>>>> >> login
>>>>>>> >> !
>>>>>>> >> no cns aaa enable
>>>>>>> >> end
>>>>>>> >>
>>>>>>> >> PE1#sh run
>>>>>>> >> Building configuration...
>>>>>>> >>
>>>>>>> >> Current configuration : 2311 bytes
>>>>>>> >> !
>>>>>>> >> version 12.0
>>>>>>> >> service timestamps debug uptime
>>>>>>> >> service timestamps log uptime
>>>>>>> >> no service password-encryption
>>>>>>> >> !
>>>>>>> >> hostname PE1
>>>>>>> >> !
>>>>>>> >> boot-start-marker
>>>>>>> >> boot-end-marker
>>>>>>> >> !
>>>>>>> >> enable password cisco
>>>>>>> >> !
>>>>>>> >> ip subnet-zero
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> ip cef
>>>>>>> >> no ip domain-lookup
>>>>>>> >> ip ssh time-out 120
>>>>>>> >> ip ssh authentication-retries 3
>>>>>>> >> mpls label protocol ldp
>>>>>>> >> no mpls traffic-eng auto-bw timers frequency 0
>>>>>>> >> frame-relay switching
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> pseudowire-class l2inter
>>>>>>> >> encapsulation mpls
>>>>>>> >> interworking ethernet
>>>>>>> >> !
>>>>>>> >> pseudowire-class INTERWORKING
>>>>>>> >> encapsulation mpls
>>>>>>> >> interworking ethernet
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> interface Loopback0
>>>>>>> >> ip address 1.1.1.1 255.255.255.255
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Loopback1
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> !
>>>>>>> >> interface FastEthernet0/0
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/0
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> encapsulation frame-relay
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/1
>>>>>>> >> ip address 150.1.12.1 255.255.255.0
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> mpls label protocol ldp
>>>>>>> >> tag-switching ip
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/2
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/3
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/4
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/5
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/6
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> interface Serial1/7
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> no clns route-cache
>>>>>>> >> !
>>>>>>> >> router ospf 1
>>>>>>> >> router-id 1.1.1.1
>>>>>>> >> log-adjacency-changes
>>>>>>> >> network 1.1.1.1 0.0.0.0 area 0
>>>>>>> >> network 13.13.13.1 0.0.0.0 area 0
>>>>>>> >> network 0.0.0.0 255.255.255.255 area 0
>>>>>>> >> !
>>>>>>> >> ip classless
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> connect FR-VLAN-IW Serial1/0 101 l2transport
>>>>>>> >> xconnect 2.2.2.2 100 pw-class INTERWORKING
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> control-plane
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> line con 0
>>>>>>> >> exec-timeout 0 0
>>>>>>> >> privilege level 15
>>>>>>> >> logging synchronous
>>>>>>> >> stopbits 1
>>>>>>> >> line aux 0
>>>>>>> >> exec-timeout 0 0
>>>>>>> >> privilege level 15
>>>>>>> >> stopbits 1
>>>>>>> >> line vty 0 4
>>>>>>> >> password cisco
>>>>>>> >> login
>>>>>>> >> !
>>>>>>> >> no cns aaa enable
>>>>>>> >> end
>>>>>>> >>
>>>>>>> >>
>>>>>>> >>
>>>>>>> >> pe2#sh run
>>>>>>> >> Building configuration...
>>>>>>> >>
>>>>>>> >> Current configuration : 1997 bytes
>>>>>>> >> !
>>>>>>> >> version 12.0
>>>>>>> >> service timestamps debug uptime
>>>>>>> >> service timestamps log uptime
>>>>>>> >> no service password-encryption
>>>>>>> >> !
>>>>>>> >> hostname pe2
>>>>>>> >> !
>>>>>>> >> boot-start-marker
>>>>>>> >> boot-end-marker
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> ip subnet-zero
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> ip cef
>>>>>>> >> no ip domain-lookup
>>>>>>> >> ip ssh time-out 120
>>>>>>> >> ip ssh authentication-retries 3
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> pseudowire-class l2inter
>>>>>>> >> encapsulation mpls
>>>>>>> >> interworking ethernet
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> interface Loopback0
>>>>>>> >> ip address 150.1.2.2 255.255.255.255
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> !
>>>>>>> >> interface Loopback2
>>>>>>> >> ip address 2.2.2.2 255.255.255.255
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> !
>>>>>>> >> interface FastEthernet0/0
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> !
>>>>>>> >> interface Serial1/0
>>>>>>> >> ip address 150.1.12.2 255.255.255.0
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> mpls label protocol ldp
>>>>>>> >> tag-switching ip
>>>>>>> >> serial restart-delay 0
>>>>>>> >> !
>>>>>>> >> interface Serial1/1
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> !
>>>>>>> >> interface Serial1/2
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> !
>>>>>>> >> interface Serial1/3
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> !
>>>>>>> >> interface Serial1/4
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> !
>>>>>>> >> interface Serial1/5
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> !
>>>>>>> >> interface Serial1/6
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> !
>>>>>>> >> interface Serial1/7
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> serial restart-delay 0
>>>>>>> >> !
>>>>>>> >> interface FastEthernet2/0
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> no keepalive
>>>>>>> >> duplex half
>>>>>>> >> speed auto
>>>>>>> >> !
>>>>>>> >> interface FastEthernet2/0.100
>>>>>>> >> encapsulation dot1Q 100
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> xconnect 1.1.1.1 100 pw-class l2inter
>>>>>>> >> !
>>>>>>> >> interface FastEthernet2/1
>>>>>>> >> no ip address
>>>>>>> >> no ip directed-broadcast
>>>>>>> >> shutdown
>>>>>>> >> duplex half
>>>>>>> >> speed auto
>>>>>>> >> !
>>>>>>> >> router ospf 1
>>>>>>> >> log-adjacency-changes
>>>>>>> >> network 0.0.0.0 255.255.255.255 area 0
>>>>>>> >> !
>>>>>>> >> ip classless
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> control-plane
>>>>>>> >> !
>>>>>>> >> !
>>>>>>> >> line con 0
>>>>>>> >> exec-timeout 0 0
>>>>>>> >> logging synchronous
>>>>>>> >> stopbits 1
>>>>>>> >> line aux 0
>>>>>>> >> stopbits 1
>>>>>>> >> line vty 0 4
>>>>>>> >> login
>>>>>>> >> !
>>>>>>> >> no cns aaa enable
>>>>>>> >> end
>>>>>>> >>
>>>>>>> >>
>>>>>>> >> Blogs and organic groups at http://www.ccie.net
>>>>>>> >>
>>>>>>> >>
>>>>>>> _______________________________________________________________________
>>>>>>> >> Subscription information may be found at:
>>>>>>> >> http://www.groupstudy.com/list/CCIELab.html
>>>>>>> >>
>>>>>>> >>
>>>>>>> >>
>>>>>>> >>
>>>>>>> >>
>>>>>>> >>
>>>>>>> >>
>>>>>>> >>
>>>>>>> >
>>>>>>> >
>>>>>>> > --
>>>>>>> > Satinder Singh
>>>>>>> > mobile 09980075998
>>>>>>>
>>>>>>>
>>>>>>> Blogs and organic groups at http://www.ccie.net
>>>>>>>
>>>>>>>
>>>>>>> _______________________________________________________________________
>>>>>>> Subscription information may be found at:
>>>>>>> http://www.groupstudy.com/list/CCIELab.html
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>> Bryan Bartik
>>>>>> CCIE #23707 (R&S, SP), CCNP
>>>>>> Sr. Support Engineer - IPexpert, Inc.
>>>>>> URL: http://www.IPexpert.com
>>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>> --
>>>> Bryan Bartik
>>>> CCIE #23707 (R&S, SP), CCNP
>>>> Sr. Support Engineer - IPexpert, Inc.
>>>> URL: http://www.IPexpert.com
>>>>
>>>
>>>
>>>
>>> --
>>> Bryan Bartik
>>> CCIE #23707 (R&S, SP), CCNP
>>> Sr. Support Engineer - IPexpert, Inc.
>>> URL: http://www.IPexpert.com
>>>
>>
>>
>
>
> --
> Bryan Bartik
> CCIE #23707 (R&S, SP), CCNP
> Sr. Support Engineer - IPexpert, Inc.
> URL: http://www.IPexpert.com

Blogs and organic groups at http://www.ccie.net
Received on Thu Jan 14 2010 - 14:23:48 ART