Re: FR-VLAN Interworking not working

I just loaded the same lab on 12.0 and it doesn't work. The VC comes up
after awhile but no traffic passes. I should have been aware of the
bug/unsupported version! However, the lab does test on 12.2S so I would
stick with that code during your prep, especially with issues like this :)
Let me know if you have issues with 12.2S.

On Wed, Jan 13, 2010 at 10:47 AM, Bryan Bartik <bbartik_at_ipexpert.com> wrote:

> Hi, could be a bug :/ Definitely not a surprise on the SP track. Or maybe
> not supported in that version. Let me try with 12.0 code. Give me a few
> minutes and I will post back.
>
>
> On Wed, Jan 13, 2010 at 9:59 AM, Service Provider <
> service.providersa_at_gmail.com> wrote:
>
>> Hi Bryan
>>
>> Tx for the assistance.
>>
>> I've rebuilt the scenario and still no luck. What IOS are you using? I'm
>> using Version 12.0(33)S3.
>>
>> Everything looks fine except my ping fails. This is frustrating as I've
>> spent A LOT of time trying to get this to work. :(
>>
>> PE2(config-if)#do sh mpls l2 v de
>> Local interface: Fa2/0 up, line protocol up, Ethernet up
>> Destination address: 1.1.1.1, VC ID: 100, VC status: up
>>
>> Preferred path: not configured
>> Default path: active
>> Next hop: point2point
>> Output interface: Se1/0, imposed label stack {33}
>> Create time: 00:07:29, last status change time: 00:06:06
>> Signaling protocol: LDP, peer 1.1.1.1:0 up
>> Targeted Hello: 2.2.2.2(LDP Id) -> 1.1.1.1
>> MPLS VC labels: local 33, remote 33
>>
>> Group ID: local 0, remote 0
>> MTU: local 1500, remote 1500
>> Remote interface description:
>> Sequencing: receive disabled, send disabled
>> VC statistics:
>> packet totals: receive 132, send 58
>> byte totals: receive 8080, send 7994
>>
>> packet drops: receive 0, seq error 0, send 0
>>
>> E2(config-if)#do sh mpls ldp ne
>> Peer LDP Ident: 1.1.1.1:0; Local LDP Ident 2.2.2.2:0
>> TCP connection: 1.1.1.1.646 - 2.2.2.2.55744
>> State: Oper; Msgs sent/rcvd: 19/19; Downstream
>> Up time: 00:10:59
>> LDP discovery sources:
>> Serial1/0, Src IP addr: 150.1.12.1
>> Targeted Hello 2.2.2.2 -> 1.1.1.1, active, passive
>>
>> Addresses bound to peer LDP Ident:
>> 150.1.12.1 1.1.1.1
>>
>> PE1(config-if)#do sh mpl l2 v d
>> Local interface: Se1/0 up, line protocol up, FR DLCI 102 up
>>
>> MPLS VC type is FR DLCI, interworking type is Ethernet
>> Destination address: 2.2.2.2, VC ID: 100, VC status: up
>> Preferred path: not configured
>> Default path: active
>> Next hop: point2point
>> Output interface: Se1/1, imposed label stack {33}
>> Create time: 00:09:09, last status change time: 00:06:34
>>
>> Signaling protocol: LDP, peer 2.2.2.2:0 up
>> Targeted Hello: 1.1.1.1(LDP Id) -> 2.2.2.2
>> MPLS VC labels: local 33, remote 33
>>
>> Group ID: local 0, remote 0
>> MTU: local 1500, remote 1500
>> Remote interface description:
>> Sequencing: receive disabled, send disabled
>> VC statistics:
>> packet totals: receive 61, send 146
>> byte totals: receive 8198, send 8920
>>
>> packet drops: receive 0, seq error 0, send 0
>>
>> PE1(config-if)#do sh mpls ldp ne
>> Peer LDP Ident: 2.2.2.2:0; Local LDP Ident 1.1.1.1:0
>> TCP connection: 2.2.2.2.55744 - 1.1.1.1.646
>> State: Oper; Msgs sent/rcvd: 18/19; Downstream
>> Up time: 00:10:28
>>
>> LDP discovery sources:
>> Serial1/1, Src IP addr: 150.1.12.2
>> Targeted Hello 1.1.1.1 -> 2.2.2.2, active, passive
>>
>> Addresses bound to peer LDP Ident:
>> 2.2.2.2 150.1.12.2
>>
>>
>>
>> On Wed, Jan 13, 2010 at 5:29 PM, Bryan Bartik <bbartik_at_ipexpert.com>wrote:
>>
>>> No, bridging does work. I am using your .net file. See below:
>>>
>>> CE1----Frame Switch----PE1----PE2----CE2
>>>
>>> CE1:
>>>
>>> bridge irb
>>>
>>> bridge 1 protocol ieee
>>> bridge 1 route ip
>>>
>>> interface Serial1/0
>>> no ip address
>>> encapsulation frame-relay
>>>
>>> frame-relay map bridge 101 broadcast
>>>
>>> interface BVI1
>>> ip address 10.10.10.1 255.255.255.0
>>> no clns route-cache
>>>
>>> PE1:
>>>
>>>
>>> pseudowire-class INTERWORKING
>>> encapsulation mpls
>>> interworking ethernet
>>>
>>> interface Serial1/0
>>> no ip address
>>> encapsulation frame-relay
>>>
>>>
>>> connect FR-VLAN-IW Serial1/0 101 l2transport
>>> xconnect 2.2.2.2 100 pw-class INTERWORKING
>>>
>>> PE2:
>>>
>>>
>>> pseudowire-class l2inter
>>> encapsulation mpls
>>> interworking ethernet
>>>
>>> interface FastEthernet2/0.100
>>> encapsulation dot1Q 100
>>> no cdp enable
>>>
>>> xconnect 1.1.1.1 100 pw-class l2inter
>>>
>>> CE2:
>>>
>>>
>>> interface FastEthernet1/0.100
>>> encapsulation dot1Q 100
>>> ip address 10.10.10.2 255.255.255.0
>>>
>>> Verification:
>>>
>>> PE1#show mpl l2transport vc de
>>>
>>> Local interface: Se1/0 up, line protocol up, FR DLCI 101 up
>>> MPLS VC type is Ethernet, interworking type is Ethernet <---- Bridged
>>>
>>> Destination address: 2.2.2.2, VC ID: 100, VC status: up
>>> Output interface: Se1/1, imposed label stack {16}
>>>
>>> Preferred path: not configured
>>> Default path: active
>>> Tunnel label: imp-null, next hop point2point
>>> Create time: 00:02:50, last status change time: 00:01:41
>>> Signaling protocol: LDP, peer 2.2.2.2:0 up
>>> MPLS VC labels: local 17, remote 16
>>> Group ID: local 0, remote 0
>>> MTU: local 1500, remote 1500
>>> Remote interface description:
>>> Sequencing: receive disabled, send disabled
>>> VC statistics:
>>> packet totals: receive 0, send 29
>>> byte totals: receive 0, send 1856
>>> packet drops: receive 0, send 0
>>>
>>> CE1#ping 10.10.10.2
>>>
>>> Type escape sequence to abort.
>>> Sending 5, 100-byte ICMP Echos to 10.10.10.2, timeout is 2 seconds:
>>> .!!!!
>>> Success rate is 80 percent (4/5), round-trip min/avg/max = 20/43/68 ms
>>> CE1#
>>>
>>>
>>>
>>>
>>>
>>> On Tue, Jan 12, 2010 at 10:12 PM, Service Provider <
>>> service.providersa_at_gmail.com> wrote:
>>>
>>>> HI guys,
>>>>
>>>> I've verified all that and unfortunately bridging does not work. I have
>>>> converted this to routed and it's working fine. No bridging on CE1 and
>>>> the 2
>>>> PEs are interworking IP.
>>>>
>>>> On Wed, Jan 13, 2010 at 6:11 AM, Satinder Singh <
>>>> satinder.iitd_at_gmail.com>wrote:
>>>>
>>>> > Hi Service provider,
>>>> >
>>>> > To me some configuration missing/inconsistency look on the PE router
>>>> and
>>>> > CE1 router.
>>>> >
>>>> > Few of them are.
>>>> >
>>>> > One the CE1 i am not able to find the interface with address
>>>> 10.1.12.1/24
>>>> > so to which interface address you are pinging from CE2... pls clarify
>>>> the
>>>> > same.
>>>> >
>>>> > On the PE1 and PE2 in pseudowire class remove the " interworking
>>>> ethernet"
>>>> > and add " interworking ip" for interworking to work.
>>>> >
>>>> > In addition it is recoomended to add "ip local interfac address
>>>> <address>"
>>>> > in the pseudowire class.
>>>> >
>>>> > Pls check and let me know if it is working.
>>>> >
>>>> > Thanks
>>>> > Satinder
>>>> >
>>>> > On Wed, Jan 13, 2010 at 12:37 AM, Service Provider <
>>>> > service.providersa_at_gmail.com> wrote:
>>>> >
>>>> >> Hi all
>>>> >>
>>>> >> I have setup FR-VLAN Interworking and my l2 tunnel is up but cannot
>>>> ping
>>>> >> between CE sites.
>>>> >>
>>>> >>
>>>> >>
>>>> CE1-----FRSW-------PE1-----------------PE2---------------------VLAN100--------------------CE2
>>>> >>
>>>> >> Configs below, please help....tx.
>>>> >>
>>>> >> CE1#
>>>> >> CE1#sh run
>>>> >> Building configuration...
>>>> >>
>>>> >> Current configuration : 1912 bytes
>>>> >> !
>>>> >> version 12.0
>>>> >> service timestamps debug uptime
>>>> >> service timestamps log uptime
>>>> >> no service password-encryption
>>>> >> !
>>>> >> hostname CE1
>>>> >> !
>>>> >> boot-start-marker
>>>> >> boot-end-marker
>>>> >> !
>>>> >> enable password cisco
>>>> >> !
>>>> >> ip subnet-zero
>>>> >> !
>>>> >> !
>>>> >> ip cef
>>>> >> no ip domain-lookup
>>>> >> ip ssh time-out 120
>>>> >> ip ssh authentication-retries 3
>>>> >> no mpls traffic-eng auto-bw timers frequency 0
>>>> >> bridge irb
>>>> >> !
>>>> >> !
>>>> >> !
>>>> >> interface FastEthernet0/0
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/0
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> encapsulation frame-relay
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> frame-relay map bridge 101 broadcast
>>>> >> frame-relay map bridge 100 broadcast
>>>> >> no frame-relay inverse-arp
>>>> >> bridge-group 1
>>>> >> !
>>>> >> interface Serial1/1
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/2
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/3
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/4
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/5
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/6
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/7
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface BVI1
>>>> >> ip address 10.10.10.1 255.255.255.0
>>>> >> no ip directed-broadcast
>>>> >> no clns route-cache
>>>> >> !
>>>> >> ip classless
>>>> >> !
>>>> >> !
>>>> >> !
>>>> >> control-plane
>>>> >> !
>>>> >> bridge 1 protocol ieee
>>>> >> bridge 1 route ip
>>>> >> !
>>>> >> line con 0
>>>> >> exec-timeout 0 0
>>>> >> privilege level 15
>>>> >> logging synchronous
>>>> >> stopbits 1
>>>> >> line aux 0
>>>> >> exec-timeout 0 0
>>>> >> privilege level 15
>>>> >> stopbits 1
>>>> >> line vty 0 4
>>>> >> password cisco
>>>> >> login
>>>> >> !
>>>> >> no cns aaa enable
>>>> >> end
>>>> >>
>>>> >>
>>>> >> ce2#
>>>> >> ce2#sh run
>>>> >> Building configuration...
>>>> >>
>>>> >> Current configuration : 810 bytes
>>>> >> !
>>>> >> version 12.0
>>>> >> service timestamps debug uptime
>>>> >> service timestamps log uptime
>>>> >> no service password-encryption
>>>> >> !
>>>> >> hostname ce2
>>>> >> !
>>>> >> boot-start-marker
>>>> >> boot-end-marker
>>>> >> !
>>>> >> !
>>>> >> ip subnet-zero
>>>> >> !
>>>> >> !
>>>> >> ip cef
>>>> >> ip ssh time-out 120
>>>> >> ip ssh authentication-retries 3
>>>> >> !
>>>> >> !
>>>> >> !
>>>> >> interface FastEthernet0/0
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> !
>>>> >> interface FastEthernet1/0
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> duplex half
>>>> >> speed auto
>>>> >> !
>>>> >> interface FastEthernet1/0.100
>>>> >> encapsulation dot1Q 100
>>>> >> ip address 10.1.12.2 255.255.255.0
>>>> >> no ip directed-broadcast
>>>> >> !
>>>> >> interface FastEthernet1/1
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> duplex half
>>>> >> speed auto
>>>> >> !
>>>> >> ip classless
>>>> >> !
>>>> >> !
>>>> >> !
>>>> >> control-plane
>>>> >> !
>>>> >> !
>>>> >> line con 0
>>>> >> exec-timeout 0 0
>>>> >> logging synchronous
>>>> >> stopbits 1
>>>> >> line aux 0
>>>> >> stopbits 1
>>>> >> line vty 0 4
>>>> >> login
>>>> >> !
>>>> >> no cns aaa enable
>>>> >> end
>>>> >>
>>>> >> PE1#sh run
>>>> >> Building configuration...
>>>> >>
>>>> >> Current configuration : 2311 bytes
>>>> >> !
>>>> >> version 12.0
>>>> >> service timestamps debug uptime
>>>> >> service timestamps log uptime
>>>> >> no service password-encryption
>>>> >> !
>>>> >> hostname PE1
>>>> >> !
>>>> >> boot-start-marker
>>>> >> boot-end-marker
>>>> >> !
>>>> >> enable password cisco
>>>> >> !
>>>> >> ip subnet-zero
>>>> >> !
>>>> >> !
>>>> >> ip cef
>>>> >> no ip domain-lookup
>>>> >> ip ssh time-out 120
>>>> >> ip ssh authentication-retries 3
>>>> >> mpls label protocol ldp
>>>> >> no mpls traffic-eng auto-bw timers frequency 0
>>>> >> frame-relay switching
>>>> >> !
>>>> >> !
>>>> >> pseudowire-class l2inter
>>>> >> encapsulation mpls
>>>> >> interworking ethernet
>>>> >> !
>>>> >> pseudowire-class INTERWORKING
>>>> >> encapsulation mpls
>>>> >> interworking ethernet
>>>> >> !
>>>> >> !
>>>> >> interface Loopback0
>>>> >> ip address 1.1.1.1 255.255.255.255
>>>> >> no ip directed-broadcast
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Loopback1
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> !
>>>> >> interface FastEthernet0/0
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/0
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> encapsulation frame-relay
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/1
>>>> >> ip address 150.1.12.1 255.255.255.0
>>>> >> no ip directed-broadcast
>>>> >> mpls label protocol ldp
>>>> >> tag-switching ip
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/2
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/3
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/4
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/5
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/6
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> interface Serial1/7
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> no clns route-cache
>>>> >> !
>>>> >> router ospf 1
>>>> >> router-id 1.1.1.1
>>>> >> log-adjacency-changes
>>>> >> network 1.1.1.1 0.0.0.0 area 0
>>>> >> network 13.13.13.1 0.0.0.0 area 0
>>>> >> network 0.0.0.0 255.255.255.255 area 0
>>>> >> !
>>>> >> ip classless
>>>> >> !
>>>> >> !
>>>> >> connect FR-VLAN-IW Serial1/0 101 l2transport
>>>> >> xconnect 2.2.2.2 100 pw-class INTERWORKING
>>>> >> !
>>>> >> !
>>>> >> !
>>>> >> control-plane
>>>> >> !
>>>> >> !
>>>> >> line con 0
>>>> >> exec-timeout 0 0
>>>> >> privilege level 15
>>>> >> logging synchronous
>>>> >> stopbits 1
>>>> >> line aux 0
>>>> >> exec-timeout 0 0
>>>> >> privilege level 15
>>>> >> stopbits 1
>>>> >> line vty 0 4
>>>> >> password cisco
>>>> >> login
>>>> >> !
>>>> >> no cns aaa enable
>>>> >> end
>>>> >>
>>>> >>
>>>> >>
>>>> >> pe2#sh run
>>>> >> Building configuration...
>>>> >>
>>>> >> Current configuration : 1997 bytes
>>>> >> !
>>>> >> version 12.0
>>>> >> service timestamps debug uptime
>>>> >> service timestamps log uptime
>>>> >> no service password-encryption
>>>> >> !
>>>> >> hostname pe2
>>>> >> !
>>>> >> boot-start-marker
>>>> >> boot-end-marker
>>>> >> !
>>>> >> !
>>>> >> ip subnet-zero
>>>> >> !
>>>> >> !
>>>> >> ip cef
>>>> >> no ip domain-lookup
>>>> >> ip ssh time-out 120
>>>> >> ip ssh authentication-retries 3
>>>> >> !
>>>> >> !
>>>> >> pseudowire-class l2inter
>>>> >> encapsulation mpls
>>>> >> interworking ethernet
>>>> >> !
>>>> >> !
>>>> >> interface Loopback0
>>>> >> ip address 150.1.2.2 255.255.255.255
>>>> >> no ip directed-broadcast
>>>> >> !
>>>> >> interface Loopback2
>>>> >> ip address 2.2.2.2 255.255.255.255
>>>> >> no ip directed-broadcast
>>>> >> !
>>>> >> interface FastEthernet0/0
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> !
>>>> >> interface Serial1/0
>>>> >> ip address 150.1.12.2 255.255.255.0
>>>> >> no ip directed-broadcast
>>>> >> mpls label protocol ldp
>>>> >> tag-switching ip
>>>> >> serial restart-delay 0
>>>> >> !
>>>> >> interface Serial1/1
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> !
>>>> >> interface Serial1/2
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> !
>>>> >> interface Serial1/3
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> !
>>>> >> interface Serial1/4
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> !
>>>> >> interface Serial1/5
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> !
>>>> >> interface Serial1/6
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> !
>>>> >> interface Serial1/7
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> serial restart-delay 0
>>>> >> !
>>>> >> interface FastEthernet2/0
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> no keepalive
>>>> >> duplex half
>>>> >> speed auto
>>>> >> !
>>>> >> interface FastEthernet2/0.100
>>>> >> encapsulation dot1Q 100
>>>> >> no ip directed-broadcast
>>>> >> xconnect 1.1.1.1 100 pw-class l2inter
>>>> >> !
>>>> >> interface FastEthernet2/1
>>>> >> no ip address
>>>> >> no ip directed-broadcast
>>>> >> shutdown
>>>> >> duplex half
>>>> >> speed auto
>>>> >> !
>>>> >> router ospf 1
>>>> >> log-adjacency-changes
>>>> >> network 0.0.0.0 255.255.255.255 area 0
>>>> >> !
>>>> >> ip classless
>>>> >> !
>>>> >> !
>>>> >> !
>>>> >> control-plane
>>>> >> !
>>>> >> !
>>>> >> line con 0
>>>> >> exec-timeout 0 0
>>>> >> logging synchronous
>>>> >> stopbits 1
>>>> >> line aux 0
>>>> >> stopbits 1
>>>> >> line vty 0 4
>>>> >> login
>>>> >> !
>>>> >> no cns aaa enable
>>>> >> end
>>>> >>
>>>> >>
>>>> >> Blogs and organic groups at http://www.ccie.net
>>>> >>
>>>> >>
>>>> _______________________________________________________________________
>>>> >> Subscription information may be found at:
>>>> >> http://www.groupstudy.com/list/CCIELab.html
>>>> >>
>>>> >>
>>>> >>
>>>> >>
>>>> >>
>>>> >>
>>>> >>
>>>> >>
>>>> >
>>>> >
>>>> > --
>>>> > Satinder Singh
>>>> > mobile 09980075998
>>>>
>>>>
>>>> Blogs and organic groups at http://www.ccie.net
>>>>
>>>> _______________________________________________________________________
>>>> Subscription information may be found at:
>>>> http://www.groupstudy.com/list/CCIELab.html
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>
>>>
>>> --
>>> Bryan Bartik
>>> CCIE #23707 (R&S, SP), CCNP
>>> Sr. Support Engineer - IPexpert, Inc.
>>> URL: http://www.IPexpert.com
>>>
>>
>>
>
>
> --
> Bryan Bartik
> CCIE #23707 (R&S, SP), CCNP
> Sr. Support Engineer - IPexpert, Inc.
> URL: http://www.IPexpert.com
>

-- 
Bryan Bartik
CCIE #23707 (R&S, SP), CCNP
Sr. Support Engineer - IPexpert, Inc.
URL: http://www.IPexpert.com
Blogs and organic groups at http://www.ccie.net