Re: building my own R&S lab

thanks to all for

On Tue, Dec 29, 2009 at 1:23 PM, Tyson Scott <tscott_at_ipexpert.com> wrote:

> Scuba,
>
> To build their rack you will need
> 6 2811's
> 6 WIC-2T's
> 8 DB60 to smart-serial back to backs
> 2 smart serial to smart-serial back to backs
> 4 3560's
> 1 older router that will support 2 or more NM modules. I think a 3640 is a
> perfect router
> 2 NM-4T's
> 1 NM-2E (This is if you want to dual purpose the frame-switch for a
> backbone router)
> Lots of 7 ft patch cables.
>
> You can then use the 3640 as your frame-switch and your backbone routers.
> You can use VRF's on the 3640 to make it appear as several backbone
> routers.
>
> That should be all the equipment you need.
>
> I am surprised you are not getting direction from NMC as to how to
> configure
> their topology. But you will need to contact them to get their frame-relay
> switch configuration and the BB router configurations. Good Luck in your
> studies.
>
> Regards,
>
> Tyson Scott - CCIE #13513 R&S, Security, and SP
> Technical Instructor - IPexpert, Inc.
> Mailto: tscott_at_ipexpert.com
> Telephone: +1.810.326.1444, ext. 208
>
>
>
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> scuba diver
> Sent: Tuesday, December 29, 2009 9:33 AM
> To: Iwan Hoogendoorn; Cisco certification
> Subject: Re: building my own R&S lab
>
> I want to buy 4 3560's and I want to buy 6 2811's with wic-2t's. Can I get
> the wic-2t's with rj45 ports so I can use cat 6 to plug them into 3560's ?
> If not, how can I connect them to the 3560's ? Do I have to have smart
> serial cables ?
> Scuba
>
> On Tue, Dec 29, 2009 at 8:01 AM, scuba diver <scuba1934_at_gmail.com> wrote:
>
> > I have NMC Cisco 360 materials and 10k to blow on equipment
> >
> >
> > On Tue, Dec 29, 2009 at 7:25 AM, Iwan Hoogendoorn
> <iwan_at_ipexpert.com>wrote:
> >
> >> What workbook are you going to study?
> >> If you just want a lab to test certain technologies/topics I would
> >> keep is small...
> >>
> >> I would even advise dynamips/GNS3
> >>
> >> If you als going to study a specific workbook (of a vendor) you can
> >> look into those workbooks ...
> >> They usually specify what equipment is used ...
> >>
> >> --
> >> Regards,
> >>
> >> Iwan Hoogendoorn
> >> CCIE #13084 (R&S / Security / SP)
> >> Sr. Support Engineer IPexpert, Inc.
> >> URL: http://www.IPexpert.com
> >>
> >> On Mon, Dec 28, 2009 at 10:11 PM, scuba diver <scuba1934_at_gmail.com>
> >> wrote:
> >> > I want to build my own R&S lab. What equipment do I need ?
> >> >
> >> > Thanks
> >> >
> >> > Scuba
> >> >
> >> >
> >> > Blogs and organic groups at http://www.ccie.net
> >> >
> >> >
> _______________________________________________________________________
> >> > Subscription information may be found at:
> >> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Tue Dec 29 2009 - 17:26:09 ART