Re: MPLS Traffic-Engineering Dynamic Tunnel

Army,
Last Error: PCALC:: No path to destination, 0000.0000.0008.00
Last Error: PCALC:: No path to destination, 0000.0000.0009.00

R8 does not have route to loopback of R9, and R9 does not have route to
loopback of R8. Enable ISIS on loopbacks by "ip router isis" or change your
TE router-ID to reachable ones.

-- 
Sincerely,
Shawn Zandi
Network Architect and Consultant
Cisco Certified CCIE x2 (R&S, Security)
Juniper, Foundry, Brocade and Procurve Certified
http://blog.shafagh.com
On Fri, Oct 30, 2009 at 6:45 PM, <armylegionmedic_at_aol.com> wrote:
> Hello Rich,
>
>
>    Thank you very much for the response. The command metric-style wide is
> in
> all the routers. When I type the command mpls traffic-eng level-* it will
> always tell me if there is no metric-style wide initiated. I have also gone
> through and checked all the routers.
>
>
> Regards,
>
>
> James
>
>
> -----Original Message-----
> From: Rich Collins <nilsi2002_at_gmail.com>
> To: Divin Mathew John <divinjohn_at_gmail.com>
> Cc: srinivas pv <vsrinivas.paturi_at_gmail.com>; armylegionmedic_at_aol.com;
> ccielab_at_groupstudy.com
> Sent: Fri, Oct 30, 2009 7:07 am
> Subject: Re: MPLS Traffic-Engineering Dynamic Tunnel
>
>
>
>
>
>
>
>
> Hi,
>
> Your problem is that all isis router instances should be metric-style
> wide for traffic engineering.
>
> If you do a show ip route isis you are probably missing some
> destinations (for the same above reason).
>
> -Rich
>
>
>
>
> > On Fri, Oct 30, 2009 at 9:00 AM, srinivas pv
> <vsrinivas.paturi_at_gmail.com>wrote:
> >
> >> Hi,
> >>
> >> You are getting following error:
> >>    Path Option 10:
> >>     Last Error: PCALC:: No path to destination, 0000.0000.0008.00
> >>
> >> You can check why you are getting this.
> >> Can you give following show outputs from both R8 and R9
> >>
> >> show mpls traffic-eng topology brief
> >> show mpls traffic-eng tunnels topology path destination <tunnel dest
> addr>
> >> show mpls traffic-eng tunnels topology path destination <tunnel dest
> addr>
> >> bandwidth
> >> show mpls traffic-eng tunnels topology path destination <tunnel dest
> addr>
> >> priority
> >> show mpls traffic-eng tunnels topology path tunnel89
> >> show mpls traffic-eng tunnels topology path tunnel89 bandwidth
> >> show mpls traffic-eng tunnels topology path tunnel89 priority
> >>
> >>
> >> Thanks,
> >> Srinivas
> >>
> >>
> >> On Fri, Oct 30, 2009 at 6:12 AM, <armylegionmedic_at_aol.com> wrote:
> >>
> >> > Hello Experts,
> >> >
> >> >   I have been troubleshooting this for like 2 hours now and just
> cannot
> >> see
> >> > what is wrong. I have read through the IPExpert article and tried the
> >> auto
> >> > bw
> >> > commands and it made no difference. Also, I am able to ping perfectly
> >> fine.
> >> > I
> >> > am trying to go R8-R2-R7-R9 and reverse path back, but my tunnel on R8
> >> and
> >> > R9
> >> > will not come online. I have also lowered the bandwidth on the RSVP as
> >> well
> >> > as
> >> > on the tunnel and this didnt help.
> >> >
> >> > Here is the config:
> >> >
> >> > R2
> >> > mpls traffic-eng tunn
> >> > router isis
> >> > mpls traffic-eng level-1
> >> > mpls traffic-eng rou lo0
> >> > int e0/0.28
> >> > mpls traffic-eng tunn
> >> > ip rsvp band 5000
> >> > int e0/0.27
> >> > mpls traffic-eng tunn
> >> > ip rsvp band 5000
> >> > r7
> >> > mpls traffic-eng tunn
> >> > router isis
> >> > mpls traffic-eng rout lo0
> >> > mpls traffic-eng level-1
> >> > int f1/0.27
> >> > mpls traffic-eng tunn
> >> > ip rsvp band 5000
> >> > int f1/0.79
> >> > mpls traffic-eng tunn
> >> > ip rsvp band 5000
> >> > r8
> >> > mpls traffic-eng tunn
> >> > router isis
> >> > mpls traffic-eng rou lo0
> >> > mpls traffic-eng level-1
> >> > int f1/0.28
> >> > mpls traffic-eng tunn
> >> > ip rsvp band 5000
> >> > int tunn 89
> >> > ip unn lo0
> >> > tunn so lo0
> >> > tunn dest 32.32.0.9
> >> > tunn mode mpls traffic-eng
> >> > tunn mpls traffic-eng prio 7 7
> >> > tunn mpls traffic-eng band 2000
> >> > tunn mpls traffic-eng path-opt 10 dynamic
> >> > tunn mpls traffic-eng autoroute announce
> >> > r9
> >> > mpls traffic-eng tunn
> >> > router isis
> >> > metric-sty wide
> >> > mpls traffic-eng rou lo0
> >> > mpls traffic-eng level-1
> >> > int f1/0.79
> >> > mpls traffic-eng tunn
> >> > ip rsvp band 5000
> >> > int tunn 98
> >> > ip unn lo0
> >> > tunn so lo0
> >> > tunn dest 32.32.0.8
> >> > tunn mode mpls traffic-eng
> >> > tunn mpls traffic-eng prio 7 7
> >> > tunn mpls traffic-eng band 2000
> >> > tunn mpls traffic-eng path-opt 10 dynamic
> >> > tunn mpls traffic-eng autoroute announce
> >> >
> >> > If I do a sh mpls traff tunn I get
> >> >
> >> > R9
> >> >
> >> > Rack1R9(config-if)#do sh mpls traffi tunn
> >> > Name: Rack1R9_t98                         (Tunnel98) Destination:
> >> 32.32.0.8
> >> >  Status:
> >> >    Admin: up         Oper: down   Path: not valid   Signalling: Down
> >> >    path option 10, type dynamic
> >> >  Config Parameters:
> >> >    Bandwidth: 2000      kbps (Global)  Priority: 7  7   Affinity:
> >> > 0x0/0xFFFF
> >> >    Metric Type: TE (default)
> >> >    AutoRoute:  enabled   LockDown: disabled  Loadshare: 500
> bw-based
> >> >    auto-bw: disabled
> >> >  History:
> >> >    Tunnel:
> >> >      Time since created: 32 minutes, 28 seconds
> >> >    Path Option 10:
> >> >      Last Error: PCALC:: No path to destination, 0000.0000.0008.00
> >> >
> >> > R8
> >> > Rack1R8(config-if)#do sh mpls traffi tunn
> >> > Name: Rack1R8_t89                         (Tunnel89) Destination:
> >> 32.32.0.9
> >> >  Status:
> >> >    Admin: up         Oper: down   Path: not valid   Signalling: Down
> >> >    path option 10, type dynamic
> >> >  Config Parameters:
> >> >    Bandwidth: 500      kbps (Global)  Priority: 7  7   Affinity:
> >> 0x0/0xFFFF
> >> >    Metric Type: TE (default)
> >> >    AutoRoute:  enabled   LockDown: disabled  Loadshare: 500
> bw-based
> >> >    auto-bw: disabled
> >> >  History:
> >> >    Tunnel:
> >> >      Time since created: 33 minutes, 15 seconds
> >> >    Path Option 10:
> >> >      Last Error: PCALC:: No path to destination, 0000.0000.0009.00
> >> > Rack1R8(config-if)#
> >> >
> >> > TIA for any help.
> >> >
> >> > Regards,
> >> >
> >> > James
> >> >
> >> >
> >> > Blogs and organic groups at http://www.ccie.net
> >> >
> >> >
> _______________________________________________________________________
> >> > Subscription information may be found at:
> >> > http://www.groupstudy.com/list/CCIELab.html
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >
> >
> > --
> >
> > Sent from Karnataka, India
> > Jean Cocteau <http://www.quotationspage.com/quote/1031.html>  - "We must
> > believe in luck. For how else can we explain the success of those we
> don't
> > like?"
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net