I am using * *WS-X6724-SFP line cards and i have found out that  VPLS is
supported only on ES, SPA and OSM line cards.. Would anyone confirm please?
On Thu, Jul 9, 2009 at 9:46 AM, Ali El Moussaoui <mousawi.ali_at_gmail.com>wrote:
> I can't make the l2 vc go to UP state what i am missing??
>
> PE1
> =========
>
> bbey7101#sh vfi CCM
> VFI name: CCM, state: up
>   VPN ID: 100
>   Local attachment circuits:
>     Vlan10
>   Neighbors connected via pseudowires:
>   Peer Address     VC ID     Split-horizon
>    10.230.55.2      100           Y
>
>
> bbey7101#sh mpls l2 vc
>
> Local intf     Local circuit        Dest address    VC ID      Status
> -------------  -------------------- --------------- ----------
> ----------
> VFI CCM        VFI                  10.230.55.2     100        DOWN
>
> bbey7101#sh xconnect pwmib
>
> VCINDEX     VC ID       Peer Address     Encap    Status
> Interface
> 20          100         10.230.55.2      MPLS     up
>
> PE2
> =========
> bbey7102#sh vfi CCM
> VFI name: CCM, state: up
>   VPN ID: 100
>   Local attachment circuits:
>     Vlan10
>   Neighbors connected via pseudowires:
>   Peer Address     VC ID     Split-horizon
>   10.230.55.1      100           Y
>
>
> bbey7102#sh mpls l2 vc
> Local intf     Local circuit        Dest address    VC ID      Status
> -------------  -------------------- --------------- ---------- ----------
>
> VFI CCM        VFI                  10.230.55.1     100
> DOWN
>
>
>
> bbey7102#sh xconnect pwmib
> VCINDEX     VC ID       Peer Address     Encap    Status
> Interface
> 20          100         10.230.55.1      MPLS     up
>
> On Wed, Jul 8, 2009 at 3:43 PM, Ali El Moussaoui <mousawi.ali_at_gmail.com>wrote:
>
>> ok thanks guys.
>>
>> We have 2 PEs and MetroSwitches connected to those PEs where CEs connect.
>>
>> - What will be the port config on the metroswitch facing the CE?
>> - What should be the port config on the metroswitch facing the PE?
>>
>> PE1 Config:
>> =========
>> l2 vfi CCM manual
>>  vpn id 100
>>  neighbor 10.230.55.2 encapsulation mpls
>>
>> interface Vlan10
>>  no ip address
>>  xconnect vfi CCM
>>
>>  interface GigabitEthernet5/9
>>  description To MetroSwitch3750
>>  switchport
>>  switchport trunk encapsulation dot1q
>>   switchport mode trunk
>>  PE2Config:
>> =========
>> l2 vfi CCM manual
>>  vpn id 100
>>  neighbor 10.230.55.1 encapsulation mpls
>>
>> interface Vlan10
>>  no ip address
>>  xconnect vfi CCM
>>
>>  interface GigabitEthernet5/9
>>  description To MetroSwitch3750
>>  switchport
>>  switchport trunk encapsulation dot1q
>>  switchport mode trunk
>>
>> On Wed, Jul 8, 2009 at 11:44 AM, backbone systems <
>> backbone.systems_at_gmail.com> wrote:
>>
>>> There is a short nice article from Petr of IE on VPLS....Poor Man
>>> VPLS....check this out....
>>>
>>>
>>> http://blog.internetworkexpert.com/category/ccie-service-provider/layer-2-technologies/
>>>
>>> Also if u need a quick review...MPLS Configuration on Cisco IOS
>>> Software has a section on it....
>>>
>>> Some real workd stuff,
>>>
>>> http://www.networkworld.com/news/2007/031207-verizon-vpls.html
>>>
>>> http://www.podtech.net/home/3180/verizon-bsiness-new-wan-options-with-vpls
>>>
>>>
>>>
>>> On Wed, Jul 8, 2009 at 10:50 AM, Ali El Moussaoui<mousawi.ali_at_gmail.com>
>>> wrote:
>>> > Thanks Danials,
>>> >
>>> > I didnt know about VPLS i think i ll have to read more. I have a
>>> customer
>>> > that has around 100 POS and wants to connect them to one central site
>>> using
>>> > one VLAN (one L2 broadcast domain). So u have any ref i can start from.
>>> I
>>> > never configured VPLS before!! I provided point to point solution for
>>> the
>>> > timebeing but its not scalable i will have to loose huge number of
>>> VLANs !!
>>> >
>>> > Ali
>>> >
>>> > On Wed, Jul 8, 2009 at 10:34 AM, jack daniels <jckdaniels12_at_gmail.com
>>> >wrote:
>>> >
>>> >> Hi,
>>> >>
>>> >> For that you have VPLS support. Psudowire are p-2-p.
>>> >>
>>> >> Regards
>>> >> J.Daniels
>>> >>
>>> >>   On Wed, Jul 8, 2009 at 12:41 PM, Ali El Moussaoui <
>>> mousawi.ali_at_gmail.com
>>> >> > wrote:
>>> >>
>>> >>>  Hello Guys,
>>> >>>
>>> >>> Does MPLS L2VPN support point to multipoint? can we have hub and
>>> spokes
>>> >>> topology?
>>> >>>
>>> >>> Ali
>>> >>>
>>> >>>
>>> >>> Blogs and organic groups at http://www.ccie.net
>>> >>>
>>> >>>
>>> _______________________________________________________________________
>>> >>> Subscription information may be found at:
>>> >>> http://www.groupstudy.com/list/CCIELab.html
>>> >
>>> >
>>> > Blogs and organic groups at http://www.ccie.net
>>> >
>>> > _______________________________________________________________________
>>> > Subscription information may be found at:
>>> > http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
Received on Thu Jul 09 2009 - 10:42:17 ART
This archive was generated by hypermail 2.2.0 : Sat Aug 01 2009 - 13:10:22 ART