Re: Quick question about ODR

no it doesn't support wildcard nor subnet mask, i've just checked:

Router(config)#router odr
Router(config-router)#network ?
  A.B.C.D Network number
Router(config-router)#network 10.0.0.0 ?
  <cr>
Router(config-router)#

On Mon, May 11, 2009 at 9:52 PM, Dwi Chandra <dc_at_dwichandra.info> wrote:
> I remember trying it before, if I recall correctly, ODR supports wildcards
> (classless?) if you configured it.
>
> The reason that default route goes through ODR is for several (past)
> implementation where a common ODR spoke router is the 'stub'. Thus, instead
> of putting default route via static, ODR was one of the flavor to go for.
> Besides, using ODR in cisco-only environment would speed up deployment and
> let those boxes chat by themselves on which default route to hop on to.
>
> Hope that helps :)
>
> DC
>
> On Mon, May 11, 2009 at 10:48 AM, Scott Morris <
> smorris_at_internetworkexpert.com> wrote:
>
>> Great question. B I have no idea. B :) B If it accepts wildcards, then
>> you have your answer! B I would assume so, but I haven't tried it!
>>
>>
>>
>>
>> *Scott Morris*, CCIE/x4/ (R&S/ISP-Dial/Security/Service Provider) #4713,
>>
>> JNCIE-M #153, JNCIS-ER, CISSP, et al.
>>
>> JNCI-M, JNCI-ER
>>
>> smorris_at_internetworkexpert.com
>>
>>
>> Internetwork Expert, Inc.
>>
>> http://www.InternetworkExpert.com
>>
>> Toll Free: 877-224-8987
>>
>> Outside US: 775-826-4344
>>
>>
>> Knowledge is power.
>>
>> Power corrupts.
>>
>> Study hard and be Eeeeviiiil......
>>
>>
>>
>> Ryan West wrote:
>> > Thanks Scott. Is it still in a classful format only or can wildcards
>> > be added?
>> >
>> > Sent from handheld.
>> >
>> > On May 11, 2009, at 10:39 AM, "Scott Morris"
>> > <smorris_at_internetworkexpert.com
>> > <mailto:smorris_at_internetworkexpert.com>> wrote:
>> >
>> >> I've both used one and and not used one, but never had any problem
>> >> with functionality....
>> >>
>> >> You use the network statement to DIRECT which interfaces you are
>> >> sending the 0/0 to. B Otherwise with just "router odr" you'll blast
>> >> that out to all your CDP interfaces/neighbors which may not be what
>> >> you want.
>> >>
>> >> HTH,
>> >>
>> >>
>> >>
>> >>
>> >> *Scott Morris*, CCIE/x4/ (R&S/ISP-Dial/Security/Service Provider) #4713,
>> >>
>> >> JNCIE-M #153, JNCIS-ER, CISSP, et al.
>> >>
>> >> JNCI-M, JNCI-ER
>> >>
>> >> smorris_at_internetworkexpert.com <mailto:smorris_at_internetworkexpert.com>
>> >>
>> >>
>> >> Internetwork Expert, Inc.
>> >>
>> >> http://www.InternetworkExpert.com
>> >>
>> >> Toll Free: 877-224-8987
>> >>
>> >> Outside US: 775-826-4344
>> >>
>> >>
>> >> Knowledge is power.
>> >>
>> >> Power corrupts.
>> >>
>> >> Study hard and be Eeeeviiiil......
>> >>
>> >>
>> >>
>> >>
>> >>
>> >> Ryan West wrote:
>> >>> Hello,
>> >>>
>> >>> I had my last short session on the ASET labs last night for some final
>> >>> warm-ups. B And I ran into an issue with ODR. B It seems the correct
>> answer was
>> >>> to include a network statement on the hub router. B The configuration
>> guide
>> >>> would leave you to believe that feature doesn't even exist. B As far as
>> syntax
>> >>> and timers go, it's very RIP like, so I can understand the desire to
>> want to
>> >>> include a network statement. B However, the spoke router was getting its
>> >>> default route via o... B Any idea why a network statement would be used?
>> >>>
>> >>> Thanks
>> >>>
>> >>> -ryan

Blogs and organic groups at http://www.ccie.net
Received on Sun May 17 2009 - 14:03:14 ART