I'm using around 6 + USB NICs and connecting the switches directly to those
NICs, here is my config:
[[Router R1]]
model = 3725
console = 2001
autostart = False
slot1 = NM-4T
#To SW1 F0/1
F0/0 = NIO_gen_eth:mii1
S1/0 = FRSW 1
cnfg = /home/vkaranth/CCIE/labs/r1.txt
[[Router R2]]
model = 3725
console = 2002
autostart = False
slot1 = NM-4T
#To SW2 F0/2
F0/0 = NIO_gen_eth:mii2
S1/0 = FRSW 2
cnfg = /home/vkaranth/CCIE/labs/r2.txt
[[Router R3]]
model = 3725
console = 2003
autostart = False
slot1 = NM-4T
S1/0 = FRSW 3
S1/1 = FRSW 13
S1/2 = R1 S1/1
S1/3 = R2 S1/1
#To SW1 F0/3
F0/0 = NIO_gen_eth:mii3
#To SW3 F0/3
F0/1 = NIO_gen_eth:mii7
cnfg = /home/vkaranth/CCIE/labs/r3.txt
[[Router R4]]
model = 3725
console = 2004
autostart = False
slot1 = NM-4T
#To SW2 F0/4
F0/0 = NIO_gen_eth:mii4
#To SW4 F0/4
F0/1 = NIO_gen_eth:mii8
S1/0 = FRSW 4
S1/1 = R5 S1/1
cnfg = /home/vkaranth/CCIE/labs/r4.txt
[[Router R5]]
model = 3725
console = 2005
autostart = False
slot1 = NM-4T
#To SW1 F0/5
F0/0 = NIO_gen_eth:mii5
#To SW3 F0/5
F0/1 = NIO_gen_eth:mii9
S1/0 = FRSW 5
cnfg = /home/vkaranth/CCIE/labs/r5.txt
[[Router R6]]
model = 3725
console = 2006
autostart = False
slot1 = NM-4T
#To SW2 F0/6
F0/0 = NIO_gen_eth:mii6
#To SW4 F0/6
F0/1 = NIO_gen_eth:mii10
S1/0 = FRSW 6
cnfg = /home/vkaranth/CCIE/labs/r6.txt
Regards,
Vijay Karanth
2009/5/12 Anbu <ksanpu_at_gmail.com>
> Thanks Michael , I did all , but no use , earlier cdp worked fine but could
> not form the ip connectivity , once restarted the dynamips and switches .
> now nothing working , i found that pc NIC is sending traffic and not
> receiving any packets and Processor usage also gone more than 50 for two
> devices with better idlepc value.
>
> So i am thinking to get the remote lab and practice rather than spending
> time as i donot have much time to face the lab.
>
> Thanks & Regards,
> Anbu
>
>
> O Mon, May 11, 2009 at 4:12 PM, michael haynes <mghaynes_at_gmail.com> wrote:
>
> > Try taking a switchport that your virtual router is connected to on the
> > 3550 or 3560 and do a 'no switchport' and assign the port an IP address
> on
> > the same network as the router it is connected to. Just see if you can
> ping
> > back and forth across that link. If that works, put the switchport back
> > into l2 mode and try taking a 2nd virtual router on the same vlan and
> ping
> > between the two virtual routers.
> >
> > By vlan, I mean the vlan on the 3550/3560, NOT the vlan on your dynamips
> > switch/breakout switch.
> >
> > Looking over your .net, it looks ok to me assuming that 802.1q is enabled
> > and the network card identifier is correct as shown below. You might try
> > posting the config on your breakout switch too, but that should be pretty
> > straightforward - each port connected to your 3550/3560s should be an
> access
> > port and match up to the vlans in your .net file. The port connectd to
> your
> > laptop is in trunk mode, dot1q encap, and allows all the vlans that you
> are
> > using.
> >
> > Michael
> >
> > On Mon, May 11, 2009 at 6:27 AM, Anbu <ksanpu_at_gmail.com> wrote:
> >
> >> Hi Michael ,
> >> Thanks, I am using HP Laptop , here is a option int the advance
> >> configuration option to select the 802.1q , i did that.
> >>
> >> Yes me too in the same boat , i can see all the routers but the routers
> >> donot see any of the switches , So what i did was , i have assign ip
> address
> >> to routers and try to check the connectivity to routers from the
> switches ,
> >> that also not working.
> >>
> >> anyway i will check more.
> >>
> >> Regards,
> >> Anbu
> >>
> >>
> >>
> >> On Mon, May 11, 2009 at 3:24 PM, michael haynes <mghaynes_at_gmail.com
> >wrote:
> >>
> >>> What NIC are you using? Not all NIC cards support 802.1q. If yours
> >>> does, you'll probably need to download drivers and utility programs
> from the
> >>> vendor (Intel, Broadcom, etc...) rather than your OEM site or
> >>> WindowsUpdate. Different vendors have these settings in different
> places.
> >>> Intel, for instance, has them in the System properties for the nic card
> >>> while Broadcom makes you use their manager utility to change these
> advanced
> >>> settings.
> >>>
> >>> I'm using an intel pro 1000 under gento linux and I have 802.1q
> trunking
> >>> enabled - it's working well.
> >>> The only thing I'm having trouble with right now is CDP. The breakout
> >>> switch sees the routers but the routers don't see the switch;
> everything
> >>> else I've done with routing protocols works fine though.
> >>>
> >>> Michael
> >>>
> >>> On Mon, May 11, 2009 at 5:29 AM, Anbu <ksanpu_at_gmail.com> wrote:
> >>>
> >>>> i am testing the " Real switches connected with Dynamip server". i
> >>>> have set
> >>>> up according the advice in this mail chain.
> >>>>
> >>>> Here the problem i am facing is i can see all the routers in the
> Dynamip
> >>>> Server from the brackout Switch , from the Routers on the Dynamip
> Server
> >>>> i
> >>>> cannot see any Switches including the Breakout switch.
> >>>>
> >>>> I have one doubt , do i want to configure the pc nic as trunk ? if
> >>>> so....
> >>>> how can i configure the PC ( Dynamip Server) NIC as trunk port ?
> >>>>
> >>>> here with i am attaching the netfile below
> >>>>
> >>>>
> >>>> ##################################################
> >>>> #
> >>>> # Define global router parameters for instance 1
> >>>> #
> >>>> ##################################################
> >>>>
> >>>> autostart=false
> >>>> [localhost:7200]
> >>>>
> >>>> workingdir = D:\NEW.DYNAMIPS\working
> >>>>
> >>>> [[3640]]
> >>>> #
> >>>> # Specify 3640 IOS image on Windows here:
> >>>> image = C:\Program Files\Dynamips\images\c3640-ik9o3s-mz.124-13a.bin
> >>>> #
> >>>> # Specify 3640 IOS image on Linux here:
> >>>> #image = /ios/c3640-jk9o3s-mz.123-14.T7.extracted.bin
> >>>> #
> >>>> ram = 128
> >>>> disk0 = 0
> >>>> disk1 = 0
> >>>> # Choose an idlepc value from the below
> >>>> idlepc = 0x60530870
> >>>> # idlepc = 0x60530890
> >>>> # idlepc = 0x60530a58
> >>>> # idlepc = 0x60530abc
> >>>> # idlepc = 0x605310c4
> >>>> # idlepc = 0x605e92e8
> >>>> # idlepc = 0x605e9364
> >>>> # idlepc = 0x60531394
> >>>> # idlepc = 0x605313d0
> >>>> # idlepc = 0x605313ec
> >>>> mmap = true
> >>>> # ghostios = true
> >>>>
> >>>> ###########################
> >>>> #
> >>>> # Define router instances
> >>>> #
> >>>> ###########################
> >>>>
> >>>> [[Router R1]]
> >>>> model = 3640
> >>>> autostart = false
> >>>> slot0 = NM-1FE-TX
> >>>> slot1 = NM-4T
> >>>> F0/0 = SW1 1
> >>>> S1/0 = FRSW 1
> >>>> #cnfg = D:\NEW.DYNAMIPS\initial.configs\R1.initial.config.txt
> >>>>
> >>>> [[Router R2]]
> >>>> model = 3640
> >>>> autostart = false
> >>>> slot0 = NM-1FE-TX
> >>>> slot1 = NM-4T
> >>>> F0/0 = SW1 2
> >>>> S1/0 = FRSW 2
> >>>> #cnfg = D:\NEW.DYNAMIPS\initial.configs\R2.initial.config.txt
> >>>>
> >>>> [[Router R3]]
> >>>> model = 3640
> >>>> autostart = false
> >>>> slot0 = NM-4E
> >>>> slot1 = NM-4T
> >>>> S1/0 = FRSW 3
> >>>> S1/1 = FRSW 13
> >>>> S1/2 = R1 S1/1
> >>>> S1/3 = R2 S1/1
> >>>> E0/0 = SW1 3
> >>>> E0/1 = SW1 9
> >>>> #cnfg = D:\NEW.DYNAMIPS\initial.configs\R3.initial.config.txt
> >>>>
> >>>> [[Router R4]]
> >>>> model = 3640
> >>>> autostart = false
> >>>> slot0 = NM-4E
> >>>> slot1 = NM-4T
> >>>> E0/0 = SW1 4
> >>>> E0/1 = SW1 10
> >>>> S1/0 = FRSW 4
> >>>> S1/1 = R5 S1/1
> >>>> # cnfg = D:\NEW.DYNAMIPS\initial.configs\R4.initial.config.txt
> >>>>
> >>>> [[Router R5]]
> >>>> model = 3640
> >>>> autostart = false
> >>>> slot0 = NM-4E
> >>>> slot1 = NM-4T
> >>>> E0/0 = SW1 5
> >>>> E0/1 = SW1 11
> >>>> S1/0 = FRSW 5
> >>>> # cnfg = D:\NEW.DYNAMIPS\initial.configs\R5.initial.config.txt
> >>>>
> >>>> [[Router R6]]
> >>>> model = 3640
> >>>> autostart = false
> >>>> slot0 = NM-4E
> >>>> slot1 = NM-4T
> >>>> E0/0 = SW1 6
> >>>> E0/1 = SW1 12
> >>>> S1/0 = FRSW 6
> >>>> #cnfg = D:\NEW.DYNAMIPS\initial.configs\R6.initial.config.txt
> >>>>
> >>>> [[ETHSW SW1]]
> >>>> 1 = access 101
> >>>> 2 = access 102
> >>>> 3 = access 103
> >>>> 4 = access 104
> >>>> 5 = access 105
> >>>> 6 = access 106
> >>>> #7 = access 201
> >>>> #8 = access 202
> >>>> 9 = access 203
> >>>> 10 = access 204
> >>>> 11 = access 205
> >>>> 12 = access 206
> >>>> 13 = access 224
> >>>> 14 = access 124
> >>>> 15 = dot1q 1
> >>>> NIO_gen_eth:\Device\NPF_{273C79F8-685A-4A54-BB0D-E49B1171CD3B}
> >>>>
> >>>>
> >>>> ##################################################
> >>>> #
> >>>> # Define global router parameters for instance 2
> >>>> #
> >>>> ##################################################
> >>>>
> >>>> [localhost:7201] # Talk to the 2nd dynamips process on port 7201
> >>>> udp = 11000 # Change the base udp port to 11000 (the default is
> >>>> 10000)
> >>>>
> >>>> workingdir = D:\NEW.DYNAMIPS\working
> >>>>
> >>>> [[3640]]
> >>>> #
> >>>> # Specify 3640 IOS image on Windows here:
> >>>> image = C:\Program Files\Dynamips\images\c3640-ik9o3s-mz.124-13a.bin
> >>>> #
> >>>> # Specify 3640 IOS image on Linux here:
> >>>> #image = /ios/c3640-jk9o3s-mz.123-14.T7.extracted.bin
> >>>> #
> >>>> ram = 128
> >>>> disk0 = 0
> >>>> disk1 = 0
> >>>> # Choose an idlepc value from the below
> >>>> idlepc = 0x60530870
> >>>> # idlepc = 0x60530890
> >>>> # idlepc = 0x60530a58
> >>>> # idlepc = 0x60530abc
> >>>> # idlepc = 0x605310c4
> >>>> # idlepc = 0x605e92e8
> >>>> # idlepc = 0x605e9364
> >>>> # idlepc = 0x60531394
> >>>> # idlepc = 0x605313d0
> >>>> # idlepc = 0x605313ec
> >>>> mmap = true
> >>>> # ghostios = true
> >>>>
> >>>>
> >>>> ###########################
> >>>> #
> >>>> # Define router instances
> >>>> #
> >>>> ###########################
> >>>>
> >>>>
> >>>> [[Router BB1]]
> >>>> model = 3640
> >>>> console = 2008
> >>>> autostart = false
> >>>> slot1 = NM-4T
> >>>> S1/0 = BB3 S1/0
> >>>> S1/1 = FRSW 21
> >>>> #cnfg = D:\NEW.DYNAMIPS\initial.configs/BB1.initial.config.txt
> >>>>
> >>>> [[Router BB2]]
> >>>> model = 3640
> >>>> console = 2009
> >>>> autostart = false
> >>>> slot0 = NM-4E
> >>>> E0/0 = SW1 13
> >>>> # cnfg = D:\NEW.DYNAMIPS\initial.configs/BB2.initial.config.txt
> >>>>
> >>>> [[Router BB3]]
> >>>> model = 3640
> >>>> console = 2010
> >>>> autostart = false
> >>>> slot0 = NM-4E
> >>>> slot1 = NM-4T
> >>>> E0/0 = SW1 14
> >>>> #cnfg = D:\NEW.DYNAMIPS\initial.configs/BB3.initial.config.txt
> >>>>
> >>>> [[FRSW FRSW]]
> >>>>
> >>>> # R1 to FRSW
> >>>> 1:102 = 2:201
> >>>> 1:103 = 3:301
> >>>> 1:113 = 13:311
> >>>> 1:104 = 4:401
> >>>> 1:105 = 5:501
> >>>>
> >>>> # R2 to FRSW
> >>>> 2:203 = 3:302
> >>>> 2:213 = 13:312
> >>>> 2:204 = 4:402
> >>>> 2:205 = 5:502
> >>>>
> >>>> # R3 to FRSW
> >>>> 3:304 = 4:403
> >>>> 3:305 = 5:503
> >>>> 13:314 = 4:413
> >>>> 13:315 = 5:513
> >>>>
> >>>> # R4 to FRSW
> >>>> 4:405 = 5:504
> >>>>
> >>>> # R6 to FRSW
> >>>> 6:51 = 21:51
> >>>> 6:100 = 21:100
> >>>> 6:101 = 21:101
> >>>> 6:201 = 21:201
> >>>> 6:301 = 21:301
> >>>> 6:401 = 21:401
> >>>>
> >>>>
> >>>> I have configured the breackout switch with the following port vlan
> >>>> assignment.
> >>>>
> >>>>
> >>>> fa 0/1 = switchport access101
> >>>>
> >>>> fa 0/2 =switchport access 102
> >>>>
> >>>> fa 0/3 =switchport access 103
> >>>>
> >>>> fa 0/4 = switchport access104
> >>>>
> >>>> fa 0/5 = switchport access105
> >>>>
> >>>> fa 0/6 = switchport access106
> >>>>
> >>>> fa 0/7 =switchport access 201
> >>>>
> >>>> fa 0/8 =switchport access 202
> >>>>
> >>>> fa 0/9 =switchport access 203
> >>>>
> >>>> fa 0/10 =switchport access 204
> >>>>
> >>>> fa 0/11 =switchport access 205
> >>>>
> >>>> fa 0/12 = switchport access206
> >>>>
> >>>> fa 0/13 = switchport access224
> >>>>
> >>>> fa 0/14 = switchport access124
> >>>>
> >>>>
> >>>>
> >>>> Regards,
> >>>> Anbu
> >>>>
> >>>>
> >>>> Blogs and organic groups at http://www.ccie.net
> >>>>
> >>>>
> _______________________________________________________________________
> >>>> Subscription information may be found at:
> >>>> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
Received on Tue May 12 2009 - 10:13:02 ART
This archive was generated by hypermail 2.2.0 : Mon Jun 01 2009 - 07:04:42 ART