Re: pls help, easy ospf question

when you do a show cdp nei does it show the neighbors?

On Fri, May 1, 2009 at 2:12 PM, belletjetrekken
<belletjetrekken_at_gmail.com>wrote:

> yea. i havent gotten to the frame relay sections. i just figured i would
> start on ospf lab 1.
>
> On Fri, May 1, 2009 at 3:55 PM, Ryan West <rwest_at_zyedge.com> wrote:
>
> > You're using Narbik's Soup to Nuts, right? Did you start on the
> > Frame-Relay section? I think it would be a bad idea to start on the most
> > complicated IGP for the R&S as your first IGP before verifying your
> > Frame-Relay sections.
> >
> > -----Original Message-----
> > From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> > belletjetrekken
> > Sent: Friday, May 01, 2009 4:46 PM
> > To: Bryan Bartik
> > Cc: Baik, Chan; Cisco certification
> > Subject: Re: pls help, easy ospf question
> >
> > frame relay
> >
> > R1 can't ping R2 and R3 can't ping R4.
> >
> > R1#sh ip ospf nei
> >
> > R1#
> >
> > R2#sh ip ospf nei
> >
> > Neighbor ID Pri State Dead Time Address
> Interface
> > 3.3.3.3 1 FULL/BDR 00:00:32 131.1.23.3
> > FastEthernet0/0
> > R2#
> > R3#sh ip ospf nei
> >
> > Neighbor ID Pri State Dead Time Address
> Interface
> > 2.2.2.2 1 FULL/DR 00:00:34 131.1.23.2
> > FastEthernet0/0
> > R3#
> > R4#sh ip ospf nei
> >
> > R4#
> >
> >
> >
> >
> >
> > R1#siib
> > Interface IP-Address OK? Method Status
> > Protocol
> > FastEthernet0/0 unassigned YES NVRAM up
> > up
> > Serial0/0 unassigned YES manual down
> > down
> > Serial0/0.12 131.1.12.1 YES manual down
> > down
> > FastEthernet0/1 unassigned YES NVRAM administratively
> down
> > down
> > Serial0/1 unassigned YES unset administratively
> down
> > down
> > Loopback0 1.1.1.1 YES manual up
> > up
> > R1#
> > R2#siib
> > Interface IP-Address OK? Method Status
> > Protocol
> > FastEthernet0/0 131.1.23.2 YES manual up
> > up
> > Serial0/0 unassigned YES manual down
> > down
> > Serial0/0.21 131.1.12.2 YES manual down
> > down
> > FastEthernet0/1 unassigned YES unset administratively
> down
> > down
> > Serial0/1 unassigned YES unset administratively
> down
> > down
> > Loopback0 2.2.2.2 YES manual up
> > up
> > R2#
> > R3#siib
> > Interface IP-Address OK? Method Status
> > Protocol
> > FastEthernet0/0 131.1.23.3 YES manual up
> > up
> > Serial0/0 unassigned YES manual down
> > down
> > Serial0/0.34 131.1.34.3 YES manual down
> > down
> > FastEthernet0/1 unassigned YES unset administratively
> down
> > down
> > Serial0/1 unassigned YES unset administratively
> down
> > down
> > Loopback0 3.3.3.3 YES manual up
> > up
> > R3#
> > R4#siib
> > Interface IP-Address OK? Method Status
> > Protocol
> > FastEthernet0/0 unassigned YES unset administratively
> down
> > down
> > Serial0/0 unassigned YES manual down
> > down
> > Serial0/0.43 131.1.34.3 YES manual down
> > down
> > FastEthernet0/1 unassigned YES unset administratively
> down
> > down
> > Loopback0 4.4.4.4 YES manual up
> > up
> > R4#
> >
> >
> > On Fri, May 1, 2009 at 3:07 PM, Bryan Bartik <bbartik_at_ipexpert.com>
> wrote:
> >
> > > I thought you said you could not ping between R1 and R2. Is the
> interface
> > > up/up between them? Are you using PPP or Frame-relay?
> > >
> > >
> > > On Fri, May 1, 2009 at 2:01 PM, belletjetrekken <
> > belletjetrekken_at_gmail.com
> > > > wrote:
> > >
> > >> what do i do now ?
> > >>
> > >> R1(config-subif)#frame-relay map ip 131.1.12.2 16
> > >> Only frame-relay interface-dlci command should beused on
> point-to-point
> > >> interfaces not frame-relay map
> > >>
> > >> On Fri, May 1, 2009 at 10:41 AM, Baik, Chan <Chan.Baik_at_viacom.com>
> > wrote:
> > >>
> > >> > You need to configure something like this:
> > >> >
> > >> > interface serial s0/0
> > >> > encap frame-relay
> > >> >
> > >> > interface serial s0/0.12
> > >> > frame-relay map ip <ip addr of other side> <dlci>
> > >> >
> > >> > ------------------------------
> > >> > *From:* belletjetrekken [mailto:belletjetrekken_at_gmail.com]
> > >> > *Sent:* Friday, May 01, 2009 8:38 AM
> > >> > *To:* Baik, Chan
> > >> >
> > >> > *Subject:* Re: pls help, easy ospf question
> > >> >
> > >> > frame-relay
> > >> >
> > >> > On Fri, May 1, 2009 at 10:31 AM, Baik, Chan <Chan.Baik_at_viacom.com>
> > >> wrote:
> > >> >
> > >> >> Are you supposed to use frame-relay encapsulation on serial 0/0 or
> > >> hdlc?
> > >> >>
> > >> >> ------------------------------
> > >> >> *From:* belletjetrekken [mailto:belletjetrekken_at_gmail.com]
> > >> >> *Sent:* Friday, May 01, 2009 8:28 AM
> > >> >> *To:* Ryan West
> > >> >> *Cc:* Abraham, Tharak; Baik, Chan; Cisco certification
> > >> >>
> > >> >> *Subject:* Re: pls help, easy ospf question
> > >> >>
> > >> >> here is some more layout info attached
> > >> >>
> > >> >> On Fri, May 1, 2009 at 10:23 AM, Ryan West <rwest_at_zyedge.com>
> wrote:
> > >> >>
> > >> >>> Can you ping 12.1, I don t see any hello s in that direction.
> > Also,
> > >> >>> can turn off the other debugs once you can ping and deb ip os adj
> > ?
> > >> >>>
> > >> >>>
> > >> >>>
> > >> >>> -ryan
> > >> >>>
> > >> >>>
> > >> >>>
> > >> >>> *From:* belletjetrekken [mailto:belletjetrekken_at_gmail.com]
> > >> >>> *Sent:* Friday, May 01, 2009 11:14 AM
> > >> >>> *To:* Abraham, Tharak
> > >> >>> *Cc:* Ryan West; Baik, Chan; Cisco certification
> > >> >>>
> > >> >>> *Subject:* Re: pls help, easy ospf question
> > >> >>>
> > >> >>>
> > >> >>>
> > >> >>>
> > >> >>>
> > >> >>> On Fri, May 1, 2009 at 10:08 AM, Abraham, Tharak <
> > >> >>> tharakabraham_at_gmail.com> wrote:
> > >> >>>
> > >> >>> Were the adjacencies formed before turning on authentication?
> > >> >>>
> > >> >>> Could you disable the authentication and give a shot?
> > >> >>>
> > >> >>>
> > >> >>>
> > >> >>>
> > >> >>>
> > >> >>>
> > >> >>> On Fri, May 1, 2009 at 5:03 PM, Ryan West <rwest_at_zyedge.com>
> wrote:
> > >> >>>
> > >> >>> Post debugs.
> > >> >>>
> > >> >>>
> > >> >>> -----Original Message-----
> > >> >>> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On
> > Behalf
> > >> Of
> > >> >>> belletjetrekken
> > >> >>> Sent: Friday, May 01, 2009 10:57 AM
> > >> >>> To: Baik, Chan
> > >> >>> Cc: Cisco certification
> > >> >>> Subject: Re: pls help, easy ospf question
> > >> >>>
> > >> >>> i just turned enabled the serial interfaces..but still the routes
> > are
> > >> not
> > >> >>> showing up
> > >> >>>
> > >> >>> On Fri, May 1, 2009 at 9:49 AM, Baik, Chan <Chan.Baik_at_viacom.com>
> > >> wrote:
> > >> >>>
> > >> >>> > It looks like your serial interfaces are shut down.
> > >> >>> >
> > >> >>> > -----Original Message-----
> > >> >>> > From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On
> > >> Behalf
> > >> >>> Of
> > >> >>> > junk mail
> > >> >>> > Sent: Friday, May 01, 2009 7:24 AM
> > >> >>> > To: Cisco certification
> > >> >>> > Subject: pls help, easy ospf question
> > >> >>> >
> > >> >>> > studying for my r & s, i configured 4 routers for ospf and for
> > some
> > >> >>> > reason R1's ospf routes are not showing up in the routing table,
> > can
> > >> >>> > somebody help me figure out why the routes are not showing up ?
> i
> > >> >>> > attached sh run's here..
> > >> >>> >
> > >> >>> > thanks
> > >> >>> >
> > >> >>> > belletjetrekken
> > >> >>> > R1#sh run
> > >> >>> > Building configuration...
> > >> >>> >
> > >> >>> > Current configuration : 1838 bytes
> > >> >>> > !
> > >> >>> > version 12.4
> > >> >>> > service timestamps debug datetime msec
> > >> >>> > service timestamps log datetime msec
> > >> >>> > no service password-encryption
> > >> >>> > !
> > >> >>> > hostname R1
> > >> >>> > !
> > >> >>> > boot-start-marker
> > >> >>> > boot-end-marker
> > >> >>> > !
> > >> >>> > !
> > >> >>> > no aaa new-model
> > >> >>> > !
> > >> >>> > resource policy
> > >> >>> > !
> > >> >>> > no network-clock-participate slot 1
> > >> >>> > no network-clock-participate wic 0
> > >> >>> > ip subnet-zero
> > >> >>> > ip cef
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > no ip domain lookup
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > interface Loopback0
> > >> >>> > ip address 1.1.1.1 255.0.0.0
> > >> >>> > !
> > >> >>> > interface FastEthernet0/0
> > >> >>> > no ip address
> > >> >>> > duplex auto
> > >> >>> > speed auto
> > >> >>> > !
> > >> >>> > interface Serial0/0
> > >> >>> > no ip address
> > >> >>> > no dce-terminal-timing-enable
> > >> >>> > !
> > >> >>> > interface Serial0/0.12
> > >> >>> > ip address 131.1.12.1 255.255.255.0
> > >> >>> > ip ospf message-digest-key 1 md5 Cisco12 !
> > >> >>> > interface FastEthernet0/1
> > >> >>> > no ip address
> > >> >>> > shutdown
> > >> >>> > duplex auto
> > >> >>> > speed auto
> > >> >>> > !
> > >> >>> > interface Serial0/1
> > >> >>> > no ip address
> > >> >>> > shutdown
> > >> >>> > no dce-terminal-timing-enable
> > >> >>> > !
> > >> >>> > router ospf 1
> > >> >>> > router-id 1.1.1.1
> > >> >>> > log-adjacency-changes
> > >> >>> > area 2 authentication message-digest
> > >> >>> > network 0.0.0.0 255.255.255.255 area 2
> > >> >>> > !
> > >> >>> > ip classless
> > >> >>> > !
> > >> >>> > !
> > >> >>> > no ip http server
> > >> >>> > no ip http secure-server
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > control-plane
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > alias exec siib show ip int br
> > >> >>> > alias exec scn show cdp neighbors
> > >> >>> > alias exec scnd show cdp neighbors detail alias exec svb show
> vlan
> > >> >>> brief
> > >> >>> > alias exec svs show vtp stat alias exec sion show ip ospf nei
> > alias
> > >> >>> exec
> > >> >>> > siond show ip ospf nei det alias exec siodr show ip ospf
> database
> > >> >>> router
> > >> >>> > alias exec sioi show ip ospf int alias exec sen show eigrp nei
> > alias
> > >> >>> > exec send show eigrp nei det alias exec ss show spanning-tree
> > alias
> > >> >>> exec
> > >> >>> > sss show spanning-tree summary alias exec ssd show spanning-tree
> > >> detail
> > >> >>> > alias exec ssm show spanning-tree mst alias exec ssr show
> > >> spanning-tree
> > >> >>> > root alias exec ssb show spanning-tree blockedports alias exec
> sv
> > >> show
> > >> >>> > version alias exec sir show ip route !
> > >> >>> > line con 0
> > >> >>> > exec-timeout 0 0
> > >> >>> > logging synchronous
> > >> >>> > line aux 0
> > >> >>> > line vty 0 4
> > >> >>> > login
> > >> >>> > !
> > >> >>> > !
> > >> >>> > end
> > >> >>> >
> > >> >>> > R1#
> > >> >>> > R2#sh run
> > >> >>> > Building configuration...
> > >> >>> >
> > >> >>> > Current configuration : 1974 bytes
> > >> >>> > !
> > >> >>> > version 12.4
> > >> >>> > service timestamps debug datetime msec
> > >> >>> > service timestamps log datetime msec
> > >> >>> > no service password-encryption
> > >> >>> > !
> > >> >>> > hostname R2
> > >> >>> > !
> > >> >>> > boot-start-marker
> > >> >>> > boot-end-marker
> > >> >>> > !
> > >> >>> > !
> > >> >>> > no aaa new-model
> > >> >>> > !
> > >> >>> > resource policy
> > >> >>> > !
> > >> >>> > no network-clock-participate slot 1
> > >> >>> > no network-clock-participate wic 0
> > >> >>> > ip subnet-zero
> > >> >>> > ip cef
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > no ip domain lookup
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > interface Loopback0
> > >> >>> > ip address 2.2.2.2 255.0.0.0
> > >> >>> > !
> > >> >>> > interface FastEthernet0/0
> > >> >>> > ip address 131.1.23.2 255.255.255.0
> > >> >>> > duplex auto
> > >> >>> > speed auto
> > >> >>> > !
> > >> >>> > interface Serial0/0
> > >> >>> > no ip address
> > >> >>> > no dce-terminal-timing-enable
> > >> >>> > !
> > >> >>> > interface Serial0/0.21
> > >> >>> > ip address 131.1.12.2 255.255.255.0
> > >> >>> > ip ospf message-digest-key 1 md5 Cisco12 !
> > >> >>> > interface FastEthernet0/1
> > >> >>> > no ip address
> > >> >>> > shutdown
> > >> >>> > duplex auto
> > >> >>> > speed auto
> > >> >>> > !
> > >> >>> > interface Serial0/1
> > >> >>> > no ip address
> > >> >>> > shutdown
> > >> >>> > no dce-terminal-timing-enable
> > >> >>> > !
> > >> >>> > router ospf 1
> > >> >>> > router-id 2.2.2.2
> > >> >>> > log-adjacency-changes
> > >> >>> > area 1 virtual-link 3.3.3.3
> > >> >>> > area 2 authentication message-digest
> > >> >>> > network 2.2.2.2 0.0.0.0 area 2
> > >> >>> > network 22.2.2.2 0.0.0.0 area 1
> > >> >>> > network 131.1.12.2 0.0.0.0 area 2
> > >> >>> > network 131.1.23.2 0.0.0.0 area 1
> > >> >>> > !
> > >> >>> > ip classless
> > >> >>> > !
> > >> >>> > !
> > >> >>> > ip http server
> > >> >>> > no ip http secure-server
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > control-plane
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > alias exec siib show ip int br
> > >> >>> > alias exec scn show cdp neighbors
> > >> >>> > alias exec scnd show cdp neighbors detail alias exec svb show
> vlan
> > >> >>> brief
> > >> >>> > alias exec svs show vtp stat alias exec sion show ip ospf nei
> > alias
> > >> >>> exec
> > >> >>> > siond show ip ospf nei det alias exec siodr show ip ospf
> database
> > >> >>> router
> > >> >>> > alias exec sioi show ip ospf int alias exec sen show eigrp nei
> > alias
> > >> >>> > exec send show eigrp nei det alias exec ss show spanning-tree
> > alias
> > >> >>> exec
> > >> >>> > sss show spanning-tree summary alias exec ssd show spanning-tree
> > >> detail
> > >> >>> > alias exec ssm show spanning-tree mst alias exec ssr show
> > >> spanning-tree
> > >> >>> > root alias exec ssb show spanning-tree blockedports alias exec
> sv
> > >> show
> > >> >>> > version alias exec sir show ip route !
> > >> >>> > line con 0
> > >> >>> > exec-timeout 0 0
> > >> >>> > logging synchronous
> > >> >>> > line aux 0
> > >> >>> > line vty 0 4
> > >> >>> > !
> > >> >>> > !
> > >> >>> > end
> > >> >>> >
> > >> >>> > R2#
> > >> >>> > R3#sh run
> > >> >>> > Building configuration...
> > >> >>> >
> > >> >>> > Current configuration : 1897 bytes
> > >> >>> > !
> > >> >>> > version 12.4
> > >> >>> > service timestamps debug datetime msec
> > >> >>> > service timestamps log datetime msec
> > >> >>> > no service password-encryption
> > >> >>> > !
> > >> >>> > hostname R3
> > >> >>> > !
> > >> >>> > boot-start-marker
> > >> >>> > boot-end-marker
> > >> >>> > !
> > >> >>> > !
> > >> >>> > no aaa new-model
> > >> >>> > !
> > >> >>> > resource policy
> > >> >>> > !
> > >> >>> > no network-clock-participate slot 1
> > >> >>> > no network-clock-participate wic 0
> > >> >>> > ip subnet-zero
> > >> >>> > ip cef
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > no ip domain lookup
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > interface Loopback0
> > >> >>> > ip address 3.3.3.3 255.0.0.0
> > >> >>> > !
> > >> >>> > interface FastEthernet0/0
> > >> >>> > ip address 131.1.23.3 255.255.255.0
> > >> >>> > duplex auto
> > >> >>> > speed auto
> > >> >>> > !
> > >> >>> > interface Serial0/0
> > >> >>> > no ip address
> > >> >>> > no dce-terminal-timing-enable
> > >> >>> > !
> > >> >>> > interface Serial0/0.34
> > >> >>> > ip address 131.1.34.3 255.255.255.0
> > >> >>> > !
> > >> >>> > interface FastEthernet0/1
> > >> >>> > no ip address
> > >> >>> > shutdown
> > >> >>> > duplex auto
> > >> >>> > speed auto
> > >> >>> > !
> > >> >>> > interface Serial0/1
> > >> >>> > no ip address
> > >> >>> > shutdown
> > >> >>> > no dce-terminal-timing-enable
> > >> >>> > !
> > >> >>> > router ospf 1
> > >> >>> > router-id 3.3.3.3
> > >> >>> > log-adjacency-changes
> > >> >>> > area 1 virtual-link 2.2.2.2
> > >> >>> > network 3.3.3.3 0.0.0.0 area 1
> > >> >>> > network 33.3.3.3 0.0.0.0 area 0
> > >> >>> > network 131.1.23.3 0.0.0.0 area 1
> > >> >>> > network 131.1.34.3 0.0.0.0 area 0
> > >> >>> > !
> > >> >>> > ip classless
> > >> >>> > !
> > >> >>> > !
> > >> >>> > no ip http server
> > >> >>> > no ip http secure-server
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > control-plane
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > alias exec siib show ip int br
> > >> >>> > alias exec scn show cdp neighbors
> > >> >>> > alias exec scnd show cdp neighbors detail alias exec svb show
> vlan
> > >> >>> brief
> > >> >>> > alias exec svs show vtp stat alias exec sion show ip ospf nei
> > alias
> > >> >>> exec
> > >> >>> > siond show ip ospf nei det alias exec siodr show ip ospf
> database
> > >> >>> router
> > >> >>> > alias exec sioi show ip ospf int alias exec sen show eigrp nei
> > alias
> > >> >>> > exec send show eigrp nei det alias exec ss show spanning-tree
> > alias
> > >> >>> exec
> > >> >>> > sss show spanning-tree summary alias exec ssd show spanning-tree
> > >> detail
> > >> >>> > alias exec ssm show spanning-tree mst alias exec ssr show
> > >> spanning-tree
> > >> >>> > root alias exec ssb show spanning-tree blockedports alias exec
> sv
> > >> show
> > >> >>> > version alias exec sir show ip route !
> > >> >>> > line con 0
> > >> >>> > exec-timeout 0 0
> > >> >>> > logging synchronous
> > >> >>> > line aux 0
> > >> >>> > line vty 0 4
> > >> >>> > !
> > >> >>> > !
> > >> >>> > end
> > >> >>> >
> > >> >>> > R3#
> > >> >>> > R4#sh run
> > >> >>> > Building configuration...
> > >> >>> >
> > >> >>> > Current configuration : 1683 bytes
> > >> >>> > !
> > >> >>> > version 12.4
> > >> >>> > service timestamps debug datetime msec
> > >> >>> > service timestamps log datetime msec
> > >> >>> > no service password-encryption
> > >> >>> > !
> > >> >>> > hostname R4
> > >> >>> > !
> > >> >>> > boot-start-marker
> > >> >>> > boot-end-marker
> > >> >>> > !
> > >> >>> > !
> > >> >>> > no aaa new-model
> > >> >>> > !
> > >> >>> > resource policy
> > >> >>> > !
> > >> >>> > no network-clock-participate slot 1
> > >> >>> > no network-clock-participate wic 0
> > >> >>> > ip subnet-zero
> > >> >>> > ip cef
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > no ip domain lookup
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > interface Loopback0
> > >> >>> > ip address 4.4.4.4 255.0.0.0
> > >> >>> > !
> > >> >>> > interface FastEthernet0/0
> > >> >>> > no ip address
> > >> >>> > shutdown
> > >> >>> > duplex auto
> > >> >>> > speed auto
> > >> >>> > !
> > >> >>> > interface Serial0/0
> > >> >>> > no ip address
> > >> >>> > no dce-terminal-timing-enable
> > >> >>> > !
> > >> >>> > interface Serial0/0.43
> > >> >>> > ip address 131.1.34.3 255.255.255.0
> > >> >>> > !
> > >> >>> > interface FastEthernet0/1
> > >> >>> > no ip address
> > >> >>> > shutdown
> > >> >>> > duplex auto
> > >> >>> > speed auto
> > >> >>> > !
> > >> >>> > router ospf 1
> > >> >>> > router-id 4.4.4.4
> > >> >>> > log-adjacency-changes
> > >> >>> > network 0.0.0.0 255.255.255.255 area 0
> > >> >>> > !
> > >> >>> > ip classless
> > >> >>> > !
> > >> >>> > !
> > >> >>> > no ip http server
> > >> >>> > no ip http secure-server
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > control-plane
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > !
> > >> >>> > alias exec siib show ip int br
> > >> >>> > alias exec scn show cdp neighbors
> > >> >>> > alias exec scnd show cdp neighbors detail alias exec svb show
> vlan
> > >> >>> brief
> > >> >>> > alias exec svs show vtp stat alias exec sion show ip ospf nei
> > alias
> > >> >>> exec
> > >> >>> > siond show ip ospf nei det alias exec siodr show ip ospf
> database
> > >> >>> router
> > >> >>> > alias exec sioi show ip ospf int alias exec sen show eigrp nei
> > alias
> > >> >>> > exec send show eigrp nei det alias exec ss show spanning-tree
> > alias
> > >> >>> exec
> > >> >>> > sss show spanning-tree summary alias exec ssd show spanning-tree
> > >> detail
> > >> >>> > alias exec ssm show spanning-tree mst alias exec ssr show
> > >> spanning-tree
> > >> >>> > root alias exec ssb show spanning-tree blockedports alias exec
> sv
> > >> show
> > >> >>> > version alias exec sir show ip route !
> > >> >>> > line con 0
> > >> >>> > exec-timeout 0 0
> > >> >>> > logging synchronous
> > >> >>> > line aux 0
> > >> >>> > line vty 0 4
> > >> >>> > !
> > >> >>> > !
> > >> >>> > end
> > >> >>> >
> > >> >>> > R4#
> > >> >>> >
> > >> >>> >
> > >> >>> > Blogs and organic groups at http://www.ccie.net
> > >> >>> >
> > >> >>> >
> > >>
> _______________________________________________________________________
> > >> >>> > Subscription information may be found at:
> > >> >>> > http://www.groupstudy.com/list/CCIELab.html
> > >> >>>
> > >> >>>
> > >> >>> Blogs and organic groups at http://www.ccie.net
> > >> >>>
> > >> >>>
> > >>
> _______________________________________________________________________
> > >> >>> Subscription information may be found at:
> > >> >>> http://www.groupstudy.com/list/CCIELab.html
> > >> >>>
> > >> >>>
> > >> >>> Blogs and organic groups at http://www.ccie.net
> > >> >>>
> > >> >>>
> > >>
> _______________________________________________________________________
> > >> >>> Subscription information may be found at:
> > >> >>> http://www.groupstudy.com/list/CCIELab.html
> > >>
> > >>
> > >> Blogs and organic groups at http://www.ccie.net
> > >>
> > >>
> _______________________________________________________________________
> > >> Subscription information may be found at:
> > >> http://www.groupstudy.com/list/CCIELab.html
> > >>
> > >>
> > >>
> > >>
> > >>
> > >>
> > >>
> > >>
> > >
> > >
> > > --
> > > Bryan Bartik
> > > CCIE #23707, CCNP
> > > Sr. Support Engineer - IPexpert, Inc.
> > > URL: http://www.IPexpert.com
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Fri May 01 2009 - 14:29:27 ART