Re: IS-IS issue over ethernet subinterface

Firstly I assume hardware issue... but its not. configured OSPF over the
link and adjacencies formed no issue.

R1#
*Mar 1 00:18:22.567: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on
FastEthernet0/0.12 from LOADING to FULL, Loading Done
R1#

R1#sh ip ospf neighbor

Neighbor ID Pri State Dead Time Address Interface
2.2.2.2 1 FULL/DR 00:00:35 10.10.10.2
FastEthernet0/0.12
R1#

On Wed, Apr 8, 2009 at 2:45 PM, Dishan Gamage <dishanlg_at_gmail.com> wrote:

> seems that its sending but not receiving any agj-packets from remote router
>
>
>
> On Wed, Apr 8, 2009 at 3:40 PM, Dheven <dheven_at_gmail.com> wrote:
>
>> R1#ping 10.10.10.2
>>
>> Type escape sequence to abort.
>> Sending 5, 100-byte ICMP Echos to 10.10.10.2, timeout is 2 seconds:
>> !!!!!
>> Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms
>>
>> R1#sh isis neighbors
>>
>> System Id Type Interface IP Address State Holdtime Circuit Id
>> R1#
>>
>>
>> On Wed, Apr 8, 2009 at 2:29 PM, Ernest Wambari <ewambari_at_gmail.com>wrote:
>>
>>> Hello Dheven,
>>>
>>> Please provide the following:
>>>
>>> 1.sh clns nei
>>> 2.debug isis adj-packet
>>>
>>> Regards,
>>>
>>> W.
>>>
>>> On Wed, Apr 8, 2009 at 2:57 PM, Dheven <dheven_at_gmail.com> wrote:
>>>
>>>> Hi GS,
>>>> I am having a issue setting up IS-IS over ethernet subinterfaces.
>>>>
>>>> here is my setup:
>>>>
>>>> R1 (trunk) ---(trunk) SW1 (trunk) ----(trunk) SW2 (trunk) ----- (trunk)
>>>> R2
>>>>
>>>>
>>>> R1 Configs:
>>>>
>>>> int fa0/0.12
>>>> encapsulation dot1q 12
>>>> ip address 10.10.10.1 255.255.255.0
>>>> ip router isis
>>>>
>>>> router isis
>>>> net 47.0001.0000.0000.0001.00
>>>>
>>>>
>>>> SW1 configs:
>>>>
>>>> fa0/1
>>>> switchport trunk encap dot1q
>>>> switch port trunk allowed vlan 12
>>>> switch mode trunk
>>>>
>>>> vlan 12 is carried across the trunk link between SW1 and SW2
>>>>
>>>> R2 configs:
>>>>
>>>> Int fa0/0.12
>>>> encapsulation dot1q 12
>>>> ip address 10.10.10.2 255.255.255.0
>>>> ip router isis
>>>>
>>>> router isis
>>>> net 49.0001.0000.0000.0002.00
>>>>
>>>> SW2 configs:
>>>> int fa0/2
>>>> switchport trunk encap dot1q
>>>> switch port trunk allowed vlan 12
>>>> switch mode trunk
>>>>
>>>>
>>>> Please help.
>>>>
>>>> Regards
>>>>
>>>> Dheven
>>>>
>>>>
>>>> Blogs and organic groups at http://www.ccie.net
>>>>
>>>> _______________________________________________________________________
>>>> Subscription information may be found at:
>>>> http://www.groupstudy.com/list/CCIELab.html
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>
>>
>>
>> --
>> Always forgive your enemies - Nothing annoys them so much.
>>
>>
>>
>

-- 
Always forgive your enemies - Nothing annoys them so much.
Blogs and organic groups at http://www.ccie.net