From: Nadeem Ansari (nadeem.ansari574@gmail.com)
Date: Wed Mar 18 2009 - 07:02:13 ART
The next is to shutdown all your interfaces :) juzz kiddin
Regards
Nadeem
On Wed, Mar 18, 2009 at 3:30 PM, Tharak Abraham <tharakabraham@gmail.com>wrote:
> Thanks Nadeem, i understood your point ! Though not a straightforward
> filtering, its an option too !
>
> I wonder if distribute-list and offset-list are the only two methods?
>
>
> Best Regards,
> Tharak Abraham
>
>
>
> On Wed, Mar 18, 2009 at 10:44 AM, Nadeem Ansari <
> nadeem.ansari574@gmail.com> wrote:
>
>> offset-list will manipulate the metric by incrementing hop count
>> you can have multiple options with offset-list either you can use that
>> route as a backup (higher metric) or you can permanently restrict it from
>> entering in to routing table by manipulating its hop count as 16
>> (unreachable) :)
>>
>> Finally all depends on the question asked and person's ease
>>
>> Regards
>> Nadeem
>>
>> On Wed, Mar 18, 2009 at 3:33 AM, Tharak Abraham <
>> tharakabraham@gmail.com> wrote:
>>
>>>
>>> Yes !
>>>
>>> @ Backbone and Naveed :- I tried out the options with access lists and
>>> prefix lists with the distribute list under the routing process
>>> to make it work.
>>> Are there more methods ? Basically i wanted to explore all other
>>> possibilities.
>>>
>>> @ Nadeem :- Dint really understand how offset list would help here as the
>>> objective is to deny the routes being sourced?
>>> If you could explain your point?
>>>
>>> Thanks a lot ppl.
>>>
>>> BR,
>>> Tharak.
>>>
>>>
>>>
>>>
>>> On Tue, Mar 17, 2009 at 11:21 AM, Nadeem Ansari <
>>> nadeem.ansari574@gmail.com> wrote:
>>>
>>>> Yeah but if you wanna use that route as a backup path then you wont be
>>>> able to achieve that, on the other hand offset-list gives you that option
>>>> also :)
>>>>
>>>> Regards
>>>> Nadeem
>>>>
>>>> On Tue, Mar 17, 2009 at 3:11 PM, backbone systems <
>>>> backbone.systems@gmail.com> wrote:
>>>>
>>>>> U can use distribute list in router mode to deny a particular route
>>>>> from a particular interface.....
>>>>>
>>>>> router rip
>>>>> distribute-list 1 out serial 1/0
>>>>> distribute-list 2 out serial 2/0
>>>>>
>>>>> access-list 1 deny 3.0.0.0 0.255.255.255
>>>>> access-list 1 permit any
>>>>> access-list 2 deny 33.0.0.0 0.255.255.255
>>>>> access-list 2 permit any
>>>>>
>>>>> HTH
>>>>>
>>>>> On Tue, Mar 17, 2009 at 11:20 AM, Nadeem Ansari
>>>>> <nadeem.ansari574@gmail.com> wrote:
>>>>> > Hi,
>>>>> >
>>>>> > 1) You can use offset-list while increasing hop count for a
>>>>> perticular route
>>>>> > learned from an interface.
>>>>> >
>>>>> > Regards
>>>>> > Nadeem
>>>>> > On Tue, Mar 17, 2009 at 3:31 AM, Tharak Abraham <
>>>>> tharakabraham@gmail.com>wrote:
>>>>> >
>>>>> >> Router R3 advertising RIPv2 routes 3.0.0.0/8 and 33.0.0.0/8 out two
>>>>> >> interfaces s1/0 (frame relay) and s2/0(serial)
>>>>> >> As Both these interfaces are connected to the same router, theres a
>>>>> need to
>>>>> >> filter redundant routes !
>>>>> >>
>>>>> >> What are the available methods by which i could permit 3.0.0.0/8out of
>>>>> >> s2/0
>>>>> >> and 33.0.0.0/8 out of s1/0 respectively and selectively ?
>>>>> >> Please refer the diag below.
>>>>> >>
>>>>> >> 33.0.0.0/8 (lo1)
>>>>> >> |
>>>>> >> (13.0.0.3) s2/0 -------- R3 (RIPv2)------- s1/0 (12.0.0.3)
>>>>> >> |
>>>>> >> 3.0.0.0/8 (lo2)
>>>>> >>
>>>>> >>
>>>>> >> BR,
>>>>> >> Tharak.
>>>>> >>
>>>>> >>
>>>>> >> Blogs and organic groups at http://www.ccie.net
>>>>> >>
>>>>> >>
>>>>> _______________________________________________________________________
>>>>> >> Subscription information may be found at:
>>>>> >> http://www.groupstudy.com/list/CCIELab.html
>>>>> >
>>>>> >
>>>>> > Blogs and organic groups at http://www.ccie.net
>>>>> >
>>>>> >
>>>>> _______________________________________________________________________
>>>>> > Subscription information may be found at:
>>>>> > http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Mon Apr 06 2009 - 06:44:05 ART