From: Sidda6 (sidda6@gmail.com)
Date: Wed Feb 11 2009 - 10:11:28 ARST
Exactly. It is working in that way.
On Mon, Feb 9, 2009 at 5:50 AM, NET HE <he_net@hotmail.com> wrote:
> To be honest, I have thought that I had known it very well until your
> question caught me off-guard.
>
> I knew that a dynamic routing protocol was needed, so I enabled IPV6 RIP in
> the tunnel interface, but I didn't enable IPV6 RIP in the unnumbered
> interface. Then I checked ipv6 routing table, there was no remote network. I
> puzzled, why. Then I enabled IPV6 ospf in the tunnel interface too without
> unnumbered interface enabled, IPV6 ospf adjacency was established, but still
> no remote network.
>
> At this moment, I realized I had to enable dynamic routing protocol under
> the unnumbered interface in order to advertise it out. I did it, then the
> remote network came to the ipv6 routing table. I pinged it successfully.
>
> Best Regards,
> Net (Xin) He
>
>
>
>
>> Date: Sun, 8 Feb 2009 19:01:06 +0100
>> Subject: Re: ipv6 unnumbered
>> From: slidersv@gmail.com
>> To: sidda6@gmail.com
>> CC: ccielab@groupstudy.com
>>
>> Well, Is your FE0/0 enabled for ipv6 and has an ipv6 address assigned?
>>
>>
>> On Sun, Feb 8, 2009 at 6:51 PM, Sidda6 <sidda6@gmail.com> wrote:
>>
>> > Hi Gs,
>> >
>> > I am trying to make manual ipv6 tunneling over ipv4. Configs are
>> >
>> > Router Z#
>> > interface Tunnel0
>> > no ip address
>> > ipv6 unnumbered FastEthernet0/0
>> > tunnel source 7.7.7.7
>> > tunnel destination 8.8.8.8
>> > tunnel mode ipv6ip
>> > end
>> >
>> > Router X#
>> > interface Tunnel0
>> > no ip address
>> > ipv6 unnumbered FastEthernet0/0
>> > tunnel source 8.8.8.8
>> > tunnel destination 7.7.7.7
>> > tunnel mode ipv6ip
>> > end
>> >
>> >
>> > =>Tunnel destination/source on each router is loopbacks addresses.
>> > => configured ipv6 address on fastethernet 0/0 of each router.
>> > => Tunnel interface status is as follows
>> > X#show ip inter brief | in Tunn|IP-A
>> > Interface IP-Address OK? Method Status
>> > Protocol
>> > Tunnel0 unassigned YES manual up
>> > up
>> >
>> > Z#show ip inter brief | in Tunn|IP-A
>> > Interface IP-Address OK? Method Status
>> > Protocol
>> > Tunnel0 unassigned YES manual up
>> > up
>> >
>> > What should I do to ping other side of ipv6 interface of router X and Z.
>> >
>> > What is wrong with my config, can some one guide me..
>> >
>> >
>> > Blogs and organic groups at http://www.ccie.net
>> >
>> > _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html
>> >
>> >
>> >
>> >
>> >
>> >
>> >
>> >
>>
>>
>> --
>> Pavel Bykov
>> ----------------
>> Don't forget to help stopping the braindumps, use of which reduces value
>> of
>> your certifications. Sign the petition at http://www.stopbraindumps.com/
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>
>
> ________________________________
> Twice the fun Share photos while you chat with Windows Live Messenger.
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Sun Mar 01 2009 - 09:44:10 ARST