From: sajid mavani (sajidmavani@gmail.com)
Date: Thu Jan 15 2009 - 03:37:25 ARST
Hi,
Thanks a lot for replying back.. This is a practice secanrio , I have
simulated on the practice lab rack Its not the real lab.. I just want to be
sure whether my con figs are rite..
As i am planning to give my lab exams soon.
So seniors please guide me if u think i could do anything to get this
resolved.
As I am planning to give my lab soon..
Would appreciate if you' ll could guide me ..
Thanks once again for your speedy post.
Regards
Sam
On Thu, Jan 15, 2009 at 10:54 AM, Hobbs <deadheadblues@gmail.com> wrote:
> who says it was a real lab? its a practice lab
>
>
> On Wed, Jan 14, 2009 at 10:20 PM, Darby Weaver <ccie.weaver@gmail.com>wrote:
>
>> If he did he might be breaking the NDA...
>>
>> That's why Cisco says it is a troubleshooting exam and not just a
>> configuration exam.
>>
>>
>> Sorry man you are touching dangerous territory there.
>>
>>
>>
>>
>>
>>
>>
>>
>> On 1/14/09, Hobbs <deadheadblues@gmail.com> wrote:
>>>
>>> show us the IP addresses
>>>
>>> On Wed, Jan 14, 2009 at 9:23 PM, sajid mavani <sajidmavani@gmail.com>
>>> wrote:
>>>
>>> > Seniors,
>>> >
>>> >
>>> > I was doing a lab & got stuck as I could not get reachibilty to my
>>> Backbone
>>> > Routes (BB2 & BB3)
>>> >
>>> > In spite of knowing the complete practice Lab i could not complete it.
>>> >
>>> >
>>> > Scenario.
>>> >
>>> > R6 --- Trunk to bb1 & bb2
>>> >
>>> > BB1 - vlan 10
>>> > bb2 - vlan 20
>>> >
>>> > Configuration I did.
>>> >
>>> > R6
>>> >
>>> > Gig 0/1
>>> > no ip address
>>> > duplex full
>>> > speed 100
>>> >
>>> > int gig0/1.1
>>> > encapsulation dot1q 10
>>> > ip add .X.X.X>X/24
>>> >
>>> > int gig0/1.2
>>> > encapsulation dot1q 20
>>> > ip add X.X.X>X/24
>>> >
>>> > the port Gig 0/1 is connected to Switch 2 -- Fas 0/6
>>> >
>>> > configuration
>>> >
>>> > int fas 0/6
>>> > switch port trunk encapsulation dot1q
>>> > switch port mode trunk
>>> > switch port allowed vlan 10,20
>>> >
>>> > BB1& bb2 -- connected to SW2 & SW3 fas 0/0
>>> >
>>> > *SW2*
>>> >
>>> > conf t
>>> >
>>> > int fas 0/0
>>> > switchport mode access
>>> > switchport access vlan 10
>>> >
>>> > *SW3*
>>> >
>>> > int fas 0/0
>>> > switchport mode access
>>> > switch port access vlan 20
>>> >
>>> > Please guide me .. I fail to understand .. I have done this many times
>>> but
>>> > some how this time It was not working.. I checked my configuration at
>>> least
>>> > 10 times.
>>> >
>>> > Apart from that the trunk links were up between all the switches &
>>> ether
>>> > channel was up .
>>> >
>>> > Later I released that the BB2 router CPU utilization reached 99% in no
>>> > time..
>>> >
>>> > I don't have any other configuration saved.. But the configuration I
>>> have
>>> > posted is the same that I have done while configuring.
>>> >
>>> > Senior please guide me, Thanks for all the support given so far.
>>> >
>>> > Awaiting your reply.
>>> >
>>> > Regards
>>> >
>>> > Sam
>>> >
>>> >
>>> > Blogs and organic groups at http://www.ccie.net
>>> >
>>> > _______________________________________________________________________
>>> > Subscription information may be found at:
>>> > http://www.groupstudy.com/list/CCIELab.html
>>>
>>>
>>> Blogs and organic groups at http://www.ccie.net
>>>
>>> _______________________________________________________________________
>>> Subscription information may be found at:
>>> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Sun Mar 01 2009 - 09:43:38 ARST