From: GAURAV MADAN (gauravmadan1177@gmail.com)
Date: Wed Dec 24 2008 - 11:47:36 ARST
just to point out that NM-16ESW is no where a comparison to a cat based L3
switch ... it just adds L2 (which can be changed to L3 ports as well) on a
router chassis .
However some thigs like vlan addition from conf mode etc etc wont show in
"?" help .. but if you go ahead and complete the CLI ; it will be accepted .
But from my view point ; not a good NM to practice for ur exam . Because
there are many thing unavailable
On Wed, Dec 24, 2008 at 5:45 AM, Jonny English <redkidneybeans@gmail.com>wrote:
> no worries.
>
> I'd suggest you hire some rack time to get all the switching stuff done.
>
> On Wed, Dec 24, 2008 at 4:23 AM, <lovnish.sharma@bt.com> wrote:
>
> > Jonny,
> >
> > Thanks for your reply.
> >
> > Are these typical issues with dynamips/Dynagen listed somewhere.
> >
> > Because its becoming very hard working on IEWB Dynamips version finding
> the
> > faults & at last problem comes out with Dynagen/Dynamip bug.
> >
> > Can anyone please advice common Dynamips bugs/issues faced while working
> on
> > IEWB Dynamips version. So that to keep in mind while working on dynamips.
> >
> > I am asking this to save some time wastage happens in finding the
> > unnecessary issues.
> >
> > Many thanks once again !!!
> >
> > Thanks,
> > Lovnish
> >
> > ________________________________
> >
> > From: Jonny English [mailto:redkidneybeans@gmail.com]
> > Sent: Tue 23/12/2008 14:46
> > To: Sharma,L,Lovnish,JPGA4X C
> > Cc: ccielab@groupstudy.com
> > Subject: Re: Configuring Etherchannel negotiation with PAgP/LAcP - NM16
> > Etherwwitch card
> >
> >
> > its not supported on dynamips. Only on mode is supported. You need to
> get
> > some real switches or rack rent them.
> >
> >
> > On Wed, Dec 24, 2008 at 3:10 AM, <lovnish.sharma@bt.com> wrote:
> >
> >
> > Hi,
> >
> > Can anybody confirm if we can configure etherchannel with
> > negotiation protocol PAgP/LAcP on 3640 Switch with NM-16ESW= card on
> > dynamips.
> >
> > I am not able to find dynamic desirable mode on it. Neither I am
> > able to configure trunk encapsulation ISL.
> >
> > I am getting the only option as ON in case of etherchannel.
> >
> > Rack1SW2(config-if)#channel-group 1 mode ?
> > on Enable Etherchannel only
> > Rack1SW2(config-if)#channel-group 1 mode
> >
> > can anyone advice on this please.
> >
> > Many thanks.
> >
> > Regards,
> > Lovnish
> >
> >
> > Blogs and organic groups at http://www.ccie.net <
> > http://www.ccie.net/>
> >
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Thu Jan 01 2009 - 12:53:09 ARST