From: Pierre-Alex Guanel (paguanel@gmail.com)
Date: Fri Dec 12 2008 - 10:59:10 ARST
Understood, but if they give you global IP addresses for the frame-relay
interfaces you will need to map these too ..
PA
On Fri, Dec 12, 2008 at 12:27 PM, Pavel Bykov <slidersv@gmail.com> wrote:
> In the LAB I would not recommend it.
> One of the very first requirements and limitations in the lab:
> "Do not create any additional subnets, unless explicitly allowed"
>
> This is in ASET labs at least. So by providing addresses to ping, you'll
> break the rule
>
> You can always ping link local addresses on the link.
> Or you can check end-to-end connectivity
> Or you can check the routing protocol status.
>
>
> On Thu, Dec 11, 2008 at 9:31 PM, Rick Mur <rick@rickmur.com> wrote:
>
>> I'd say yes, because R1 and R2 wouldn't be able to ping each other across
>> the link, so that breaks any 'full-reachability' requirement of your lab.
>>
>> Rick Mur
>> CCIE #21946
>>
>> Sent from my iPhone
>>
>>
>> On 11 dec 2008, at 21:22, <antonygrooves@gmail.com> wrote:
>>
>> Do you still recommend to double map in frame relay between two routers,
>>> not a hub and spoke network. Only R1 ---- R2
>>>
>>> Thanks again.
>>>
>>>
>>> Tony.
>>>
>>> Pierre-Alex Guanel wrote:
>>>
>>>> Yes, sure the maping at the Global level is needed for hub / spoke L3
>>>> reacheability , but not for IPv6 RIP....
>>>>
>>>> PA
>>>>
>>>>
>>>> On Thu, Dec 11, 2008 at 8:42 AM, Rick Mur <rick@rickmur.com <mailto:
>>>> rick@rickmur.com>> wrote:
>>>>
>>>> It's enough to only map the link-local in this case, although for
>>>> my feeling
>>>> I configure also a mapping to the global address. I guess it's just a
>>>> feeling, but link-local is enough :)
>>>>
>>>>
>>>> Rick Mur
>>>> CCIE #21946 (R&S)
>>>> CCNP, CCIP, JNCIA-ER, MCSE
>>>> rick@rickmur.com <mailto:rick@rickmur.com>
>>>>
>>>> On Wed, 10 Dec 2008 18:59:13 -0200
>>>> antonygrooves <antonygrooves@gmail.com
>>>> <mailto:antonygrooves@gmail.com>> wrote:
>>>> Hi Guys.
>>>>
>>>> I have a doubt regarding RIP IPV6 over Frame realy.
>>>> If its necessary to do the frame relay map for the link local and
>>>> link global, Like in OSPFV3 or just to the link local.
>>>>
>>>> In both cases y can see the routes behind the frame relay cloud,
>>>> thats why im little confused.
>>>>
>>>> Thanks a lot.
>>>>
>>>> Tony.
>>>>
>>>>
>>>> Blogs and organic groups at http://www.ccie.net
>>>>
>>>>
>>>> _______________________________________________________________________
>>>>
>>>
>>
>> Subscription information may be found at:
>>>> http://www.groupstudy.com/list/CCIELab.html
>>>>
>>>>
>>>> Blogs and organic groups at http://www.ccie.net
>>>>
>>>>
>>>> _______________________________________________________________________
>>>>
>>>
>>
>> Subscription information may be found at:
>>>> http://www.groupstudy.com/list/CCIELab.html
>>>>
>>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
>
>
> --
> Pavel Bykov
> ----------------
> Don't forget to help stopping the braindumps, use of which reduces value of
> your certifications. Sign the petition at http://www.stopbraindumps.com/
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Thu Jan 01 2009 - 12:53:08 ARST