Re: CCIE Security : Dynamips

From: Muhammad Nasim (muhammad.nasim@gmail.com)
Date: Tue Dec 09 2008 - 19:45:47 ARST

nPlease look into the following links
http://www.andersonalves.net/tutorials/

Very helpful tutorials for someone who want to start with dynamips

HTH

2008/12/9 Fred Reimer <freimer@ctiusa.com>

> nio_linux_eth:eth0.x
>
> where x is the sub-interface on your Linux box. You'd then configure
> VMware
> to bridge to this same network. As far as the dynamips setup, it is all in
> the manuals / tutorials on hacki.at.
>
>
> Fred Reimer
> Senior Network Engineer
> Coleman Technologies, Inc.
> 954-298-1697
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> jockey wearer
> Sent: Tuesday, December 09, 2008 10:35 AM
> To: Oz
> Cc: Muhammad Nasim; GS CCIE-Lab; security@groupstudy.com
> Subject: Re: CCIE Security : Dynamips
>
> Dear Mr.Nasim,
>
> Thanks for your reply but could you tell me how i can connect VMWARE
> server to dynamips switch as I am new with VMWARE.
> I tried it but it doesnot work .
> Thanks and have a nice day !
>
> Prashnat
>
> On 12/8/08, Oz <oz4xxx@gmail.com> wrote:
> > Prashant,
> >
> > You may wanna check this out
> >
>
> http://www.internetworkpro.org/wiki/CCIE_Security_Home_Lab_with_dynamips_%26
> _Co
> >
> > Cheers,
> > Oz
> >
> > On Mon, Dec 8, 2008 at 4:08 AM, Muhammad Nasim
> > <muhammad.nasim@gmail.com>wrote:
> >
> >> Not a difficult thing, connect your pix udp interface on port of the
> 3640
> >> (16port switch) and connect the vmware interface on another port of the
> >> switch and put both of them in one vlan.
> >> HTH
> >>
> >>
> >> 2008/12/7 jockey wearer <jockeywearer@gmail.com>
> >>
> >> > Dear All,
> >> >
> >> > Good Day !!
> >> >
> >> > I am using dynamiops for my CCIE security studies.
> >> > I have Installed and configured ACS on VMWARe and it is working fine .
> >> > I have prepared other scenerios with Pix and IPs seems to be working
> >> > fine
> >> .
> >> > But I stucked in one issue .I am preparing for Internetwork Expert Lab
> >> and
> >> > I
> >> > want to connect my ACS(Which is installed on Vmware ) to Pix DMZ1
> >> Interface
> >> > .
> >> > What I need to do ?
> >> > Any output really appereciate
> >> >
> >> > Thanks
> >> > Prashant
> >> >
> >> >
> >> > Blogs and organic groups at http://www.ccie.net
> >> >
> >> >
> _______________________________________________________________________
> >> > Subscription information may be found at:
> >> > http://www.groupstudy.com/list/CCIELab.html
> >> >
> >> >
> >> >
> >> >
> >> >
> >> >
> >> >
> >> >
> >>
> >>
> >> --
> >> Muhammad Nasim
> >> Network Engineer
> >> Saudi Arabia
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
>
> 

-- 
Muhammad Nasim
Network Engineer
Saudi Arabia

Blogs and organic groups at http://www.ccie.net

This archive was generated by hypermail 2.1.4 : Thu Jan 01 2009 - 12:53:08 ARST