From: Nick Matthews (matthn@gmail.com)
Date: Sat Oct 18 2008 - 14:05:09 ART
The 2500 might predate this command. Surprise!
Nick
On Sat, Oct 18, 2008 at 12:50 PM, Reza Toghraee <reza@toghraee.com> wrote:
> Thanks, but I don't have this command "isdn protocol-emulate network"
>
>
>
> FR-BB1(config-if)#do show run int bri 0
> Building configuration...
>
> Current configuration : 37 bytes
> !
> interface BRI0
> no ip address
> end
>
> FR-BB1(config)#isdn ?
> gateway-max-interworking set if gateway has to be transparent.
> leased-line Sets a BRI interface to support leased lines on
> B &
> D channels
> silent-boot Ignore ISDN lines while booting
> switch-type Select the ISDN switch type
> tei-negotiation Set when ISDN TEI negotiation should occur
> (global)
> voice-call-failure Specify what cause code to emit when a voice
> call
> fails with no specific cause code
>
>
> FR-BB1(config)#interface brI 0
> FR-BB1(config-if)#isdn ?
> T306 Specify Timer T306 in milliseconds
> T310 Specify Timer T310 in milliseconds
> all-incoming-calls-v120 Answer all incoming calls as V.120
> answer1 Specify Called Party number and subaddress
> answer2 Specify Called Party number and subaddress
> autodetect Enable the automatic spid detection
> caller Specify incoming telephone number to be verified
> calling-number Specify Calling Number included for outgoing
> calls
> conference-code Specify a Conference Code
> disconnect-cause Specify cause code to return in call rejection to
> the switch
> fast-rollover-delay Delay between fastrollover dials
> guard-timer timer to complete the call.
> ie Informational Elements
> incoming Process incoming calls
> incoming-voice Specify options for incoming calls.
> map Specify E.164 address to numbering plan/type
> mapping
> nfas-order specify nfas DSL search order
> not-end-to-end Specify speed when calls received are not isdn
> end
> to end
> outgoing Options for outgoing IEs and messages
> outgoing-voice Specify information transfer capability for voice
> calls
> overlap-receiving Specify if the interface will do Overlap
> Receiving
> piafs_enabled enable PIAFS (Personal Handy Phone System)
> reject Reject incoming calls
> send-alerting Specify if Alerting message to be sent out before
> Connect message
> sending-complete Specify if Sending Complete included in outgoing
> SETUP message
> snmp SNMP subcommands
> spid1 Specify Service Profile IDentifier
> spid2 Specify Service Profile IDentifier
> static-tei Specify a Static TEI for ISDN BRI
> switch-type Select the Interface ISDN switch type
> tei-negotiation Set when ISDN TEI negotiation should occur
> timeout-signaling Flush D channel if a signaling packet can't be
> transmitted in 1 second
> timer Specify ISDN Timer values to be changed
> transfer-code Specify a Transfer Code (Default 61)
> transition-delay Delay before bringing D channel up
> transparent Pass Cause Values transparently
> twait-disable Delay National ISDN BRI switchtype from
> activating
> interface on powerup
> v110 Specify V.110 over ISDN
> voice-priority Specify Voice Priority
> x25 Configure x25 over the D channel
>
>
>
>
>
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Nick
> Matthews
> Sent: Saturday, October 18, 2008 8:41 PM
> To: Scott M Vermillion
> Cc: Radioactive Frog; Reza Toghraee; Cisco certification
> Subject: Re: OT: is it possible to have BRI back2back connection?
>
> Yes, you can do both PRI and BRI back-to-back. T1 Crossover with
> emulate-network on one side.
>
>
> Nick
>
> On Sat, Oct 18, 2008 at 12:20 PM, Scott M Vermillion <
> scott_ccie_list@it-ag.com> wrote:
>
> > Hey Frog,
> >
> > I didn't see your reply before posting about the need for an ISDN
> > simulator.
> > This work for BRIs too? Way cool if so...
> >
> > Scott
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> > Radioactive Frog
> > Sent: Saturday, October 18, 2008 6:37 AM
> > To: Reza Toghraee
> > Cc: Cisco certification
> > Subject: Re: OT: is it possible to have BRI back2back connection?
> >
> > yes u can do that, real easy one :)
> >
> > r1---isdn pri------------r2
> >
> > just use a isdn crossover cable. remember its not E1 crsoss over, neither
> > ethernet crossover.
> >
> >
> > router1 =>isdn protocol-emulate network
> > router2 =>isdn protocol-emulate user
> >
> > confirm it using show isdn status.
> >
> > thats all.
> >
> > -frog
> >
> >
> > On Sat, Oct 18, 2008 at 8:40 PM, Reza Toghraee <reza@toghraee.com>
> wrote:
> >
> > > Hi
> > >
> > >
> > >
> > > Is there any way to connect 2 cisco 25xx routers with their BRI
> interface
> > > without any isdn switch?
> > >
> > >
> > >
> > > Thanks
> > >
> > > Reza
> > >
> > >
> > > Blogs and organic groups at http://www.ccie.net
> > >
> > > _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Sat Nov 01 2008 - 15:35:21 ARST