From: davidytk (davidytk@netvigator.com)
Date: Mon Sep 22 2008 - 12:49:46 ART
It is only ccbootcamp environment.
I haven't assign SRST default pool to RS site phone. I have attached the log
file. For 5001 (with AAR configuration), it cannot dial, for 5002 it can
dial.
Thanks
Best Regards
David
_____
From: Radioactive Frog [mailto:pbhatkoti@gmail.com]
Sent: 2008-09-22 22:48
To: davidytk
Cc: ccielab@groupstudy.com
Subject: Re: Voice Question about AAR configuration
see my answer below;
On Mon, Sep 22, 2008 at 9:56 PM, davidytk <davidytk@netvigator.com> wrote:
Hi Frog
For your questions.
1. I cannot phone 1 and phone 2 or vice-versa during 4 digit number.
Check the right device-pool is assigned to the phone1 and phone2
also check your SRST config - MGCP or H323 whatever it is.
this is the first condition that they shud be able to dial each other
locally.
2. I try to forward-digit 4 on PSTN, but it still cannot ring up at RS1.
but u said PSTN is forwarding the digits to RS1, never mind, I believe the
issue is SRST config is not okay. Both phones shud be able to ring.
IS it the lab environment or its real life scenario?
-=frog
Thanks
Best Regards
David
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Radioactive Frog
Sent: 2008-09-22 14:04
To: davidytk
Cc: ccielab@groupstudy.com
Subject: Re: Voice Question about AAR configuration
David,
Can you try a few things;
1. at RS1 - can you call from phone1 to phone 2 or vice-versa using 4 digit
numbers when SRST kicks in?
2. Try grabing some debugs from RS1 router - 'debug isdn q931' output and
post them here.
3. Make sure you've translation profile to slash down pstn digits to 4
digits so that when it hits your RS1 router it will know 4 digit phone.
Again debug isdn q931 will tell ya that whats happening at RS1 router.
HTH,
frog
On Mon, Sep 22, 2008 at 1:54 AM, davidytk <davidytk@netvigator.com> wrote:
> Dear friend
>
>
>
> I have tried to configure AAR between both site (HQ and RS1). I have
> created
> 2 locations (1 for HQ - unlimited bandwidth, 1 for RS1 - with 24kps). I
> tried to call a number (RS1 DN) from HQ phone, it has some strange thing
> happen.
>
>
>
> 1. The call has been routed to PSTN and Pass to Remote
> router, but the phone is remote site cannot ring. I checked all the
> dial-plan is correct, if I remove the location on RS, the phone ring up
> immediately.
>
> 2. For AAR concept, it is mean that if the WAN link does
> not have enough bandwidth, it will route to PSTN (Backup). When I tried to
> phone from Remote Site(not enough bandwidth) to HQ, it cannot dial, it
show
> "not enough bandwidth". I am sure I have already configured AAR group, AAR
> CSS and Location to Phone device and Gateway.
>
>
>
> Can anyone help to know what my problem faces.
>
>
>
> Thanks
>
>
>
> Best Regards
>
> David
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Sat Oct 04 2008 - 09:26:19 ART