From: Antonio Soares (amsoares@netcabo.pt)
Date: Wed Sep 03 2008 - 13:34:20 ART
It should work. I've loaded you config and i get the desired output:
++++++++++++++++++++++++++
P2#sh policy-map interface
Serial1/0
Service-policy input: EXP5
Class-map: EXP5 (match-all)
10 packets, 1120 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: mpls experimental topmost 5
QoS Set
qos-group 5
Packets marked 10
Class-map: class-default (match-any)
594 packets, 41199 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
Serial1/1
Service-policy output: MPtoMP
Class-map: MPtoMP (match-all)
10 packets, 1120 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: qos-group 5
QoS Set
mpls experimental topmost 5
Packets marked 10
Class-map: class-default (match-any)
770 packets, 52869 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
P2#
++++++++++++++++++++++++++
Which IOS release and platform are you using ?
Regards,
Antonio Soares, CCIE #18473 (R&S)
amsoares@netcabo.pt
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
backbone systems
Sent: quarta-feira, 3 de Setembro de 2008 12:57
To: Cisco certification
Cc: SP Ccie
Subject: MPLS QOS P Router Issue
Hi,
Below is the config from my P routers. On the Ingress i am marking the
traffic to qos-group 5
and on the Egress seting the mpls qos topmost to 5
All the marking is done for telnet traffic .
When i do the show policy-map on the ingress interface i can see the
the traffic marked,
R3#sh policy-map int ser2/2
Serial2/2
Service-policy input: EXP5
Class-map: EXP5 (match-all)
86 packets, 4586 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: mpls experimental topmost 5
QoS Set
qos-group 5
Packets marked 86
Class-map: class-default (match-any)
815 packets, 56475 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
But when i try to see my Egress interface , it is not setting the MPLS
EXP bit to 5
R3#sh policy-map int ser2/1
Serial2/1
Service-policy output: MPtoMP
Class-map: MPtoMP (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: qos-group 5
QoS Set
mpls experimental topmost 5
Packets marked 0
Class-map: class-default (match-any)
74 packets, 3978 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
Below is the config of my router,
R3#sh run
Building configuration...
Current configuration : 1948 bytes
!
upgrade fpd auto
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R3
!
boot-start-marker
boot-end-marker
!
logging message-counter syslog
!
no aaa new-model
ip source-route
ip cef
!
!
!
!
no ipv6 cef
!
multilink bundle-name authenticated
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
archive
log config
hidekeys
!
!
!
!
!
!
class-map match-all MPtoMP
match qos-group 5
class-map match-all EXP5
match mpls experimental topmost 5
!
!
policy-map MPtoMP
class MPtoMP
set mpls experimental topmost 5
policy-map EXP5
class EXP5
set qos-group 5
!
!
!
!
!
interface Loopback0
ip address 3.3.3.3 255.255.255.255
!
interface FastEthernet0/0
no ip address
shutdown
duplex half
!
interface Serial2/0
no ip address
encapsulation frame-relay
serial restart-delay 0
!
interface Serial2/0.2 point-to-point
ip address 20.0.0.3 255.0.0.0
snmp trap link-status
mpls ip
frame-relay interface-dlci 302
!
interface Serial2/1
ip address 14.0.0.3 255.0.0.0
mpls ip
serial restart-delay 0
service-policy output MPtoMP
!
interface Serial2/2
ip address 13.0.0.3 255.0.0.0
mpls ip
serial restart-delay 0
service-policy input EXP5
!
interface Serial2/3
no ip address
shutdown
serial restart-delay 0
!
interface ATM3/0
no ip address
shutdown
no atm ilmi-keepalive
!
interface Serial4/0
no ip address
shutdown
serial restart-delay 0
!
interface Serial4/1
no ip address
shutdown
serial restart-delay 0
!
interface Serial4/2
no ip address
shutdown
serial restart-delay 0
!
interface Serial4/3
no ip address
shutdown
serial restart-delay 0
!
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
!
logging alarm informational
!
!
!
!
!
!
!
control-plane
!
!
!
!
!
!
!
gatekeeper
shutdown
!
!
line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
end
i seems i am doing some basic mistake!!!! Can someone identify that????
BB
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Sat Oct 04 2008 - 09:26:17 ART