From: Fahad Khan (fahad.khan@gmail.com)
Date: Thu Aug 14 2008 - 15:09:07 ART
Yes dude, this is normal, Cmd "no frame-relay inverse-arp" blocks the
request only. plz go through the archives, this topic had been dicussed in
details.
On 8/14/08, cciestudy <cciestudy@mid-world.net> wrote:
>
> According to the Cisco DocCD, using "no frame inverse-arp" should disable
> ARP on the interface.
>
>
>
> "...disable Inverse ARP for all protocols supported on an interface, use
> the
> no frame-relay inverse-arp command without arguments."
>
>
>
> However, I have seen it where it does not.
>
>
>
> Given this example, I have 3 routers:
>
>
>
> R1 -----FR SW --- R3
>
> |
>
> R2
>
>
>
> DLCI map: R1 DLCI 103 >>> R3 DLCI 301
>
> R2 DLCI 102 >>>R2 DLCI 201
>
>
>
> If I do "no frame inverse-arp" on R1, but do enable it on R3.
>
> The Frame packet debug shows R3 sending the Inarp, R1 receiving and R1
> sending.
>
>
>
> If I do a "no frame inverse-arp" on both R1 and R2 DLCI's, I see no INARP
> at
> all.
>
>
>
> So, it appears that the command "no frame inverse-arp" only prevents you
> from actively sending, but the router will still send if it receives an
> INARP.
>
>
>
> Is this normal or something funky with the version of code I am using?
>
>
>
> Thanks.
>
>
>
> -----------------------------------
>
> Here is the configs and debugs:
>
>
>
>
>
> R1#
>
>
>
> interface Serial0/0
>
> ip address 192.168.1.1 255.255.255.0
>
> encapsulation frame-relay
>
> clock rate 2000000
>
> no frame-relay inverse-arp
>
> end
>
>
>
>
>
>
>
> R1#debug frame-relay packet
>
>
>
> *Mar 1 00:01:39.183: %SYS-5-CONFIG_I: Configured from console by console
>
> *Mar 1 00:01:39.187: %LINK-3-UPDOWN: Interface Serial0/0, changed state to
> up
>
> *Mar 1 00:01:40.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> Serial0/0, changed state to up
>
> *Mar 1 00:02:04.183: Serial0/0(i): dlci 103(0x1871), pkt encaps 0x0300
> 0x8000 0x0000 0x806 (ARP), datagramsize 34
>
> *Mar 1 00:02:04.191: Serial0/0: frame relay INARP received
>
> *Mar 1 00:02:04.195: FR: Sending INARP Reply on interface Serial0/0 dlci
> 103 for link 7(IP)
>
>
>
>
>
> R1#sh frame-relay map
>
> Serial0/0 (up): ip 192.168.1.3 dlci 103(0x67,0x1870), dynamic,
>
> broadcast,, status defined, active
>
>
>
> >>>> Notice I have an dynamic MAP even though it is "disabled" on the
> interface?
>
>
>
>
>
> =====
>
>
>
> R3#debug frame-relay packet
>
>
>
> *Mar 1 00:01:33.595: %LINK-3-UPDOWN: Interface Serial0/0, changed state to
> up
>
> *Mar 1 00:01:34.595: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> Serial0/0, changed state to up
>
> *Mar 1 00:02:03.607: Serial0/0(o): dlci 301(0x48D1), pkt encaps 0x0300
> 0x8000 0x0000 0x806 (ARP), datagramsize 34
>
> *Mar 1 00:02:03.607: FR: Sending INARP Request on interface Serial0/0 dlci
> 301 for link 7(IP)
>
> *Mar 1 00:02:03.631: broadcast dequeue
>
> *Mar 1 00:02:03.631: Serial0/0(o):Pkt sent on dlci 301(0x48D1), pkt encaps
> 0x300 0x8000 0x0 0x806 (ARP), datagramsize 34
>
> *Mar 1 00:02:03.703: Serial0/0(i): dlci 301(0x48D1), pkt encaps 0x0300
> 0x8000 0x0000 0x806 (ARP), datagramsize 34
>
> *Mar 1 00:02:03.707: Serial0/0: frame relay INARP received
>
>
>
> R3#sh frame-relay map
>
> Serial0/0 (up): ip 192.168.1.1 dlci 301(0x12D,0x48D0), dynamic,
>
> broadcast,, status defined, active
>
>
>
> >>>. Note I see INARP even though R1 should not be sending? Right?
>
>
>
> R3#
>
>
>
> interface Serial0/0
>
> ip address 192.168.1.3 255.255.255.0
>
> encapsulation frame-relay
>
> clock rate 2000000
>
> end
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
>
-- *FAHAD KHANBE Computer Systems NED,
CCNA,CCDA,CCNP,FOUNDFE,CLSE,QOS,JNCIA,JNCIS,MCP,CCIE (Written)
Systems Support Engineer, Premier Systems (Pvt) limited,
Karachi, Pakistan
92-321-2370510.*
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Mon Sep 01 2008 - 08:15:30 ART