From: Greg Martin (justler@krweb.net)
Date: Tue Jul 15 2008 - 03:12:31 ART
Will try this when I get home. I couldn't get into bugtrack for the last
day or so to check... kept giving me a wierd error.
Thanks for the lead, Nick.
Regards,
Greg
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of Nick
Matthews
Sent: Monday, July 14, 2008 10:22 PM
To: Greg Martin
Cc: Cisco certification
Subject: Re: IAD 2431 w/ T1 ports and 12.4. Keep getting BERT messages when
configuring controller
You may want to try 12.4(20)T, just came out, has a fix for this bug:
CSCso22149
On Sun, Jul 13, 2008 at 12:32 PM, Greg Martin <justler@krweb.net> wrote:
> IADs have integrated T1/E1 ports and 1WIC slot. The ports i'm trying on
> different IADs are all integrated.
>
>
>
> _____
>
> From: Jason Madsen [mailto:madsen.jason@gmail.com]
> Sent: Sunday, July 13, 2008 11:57 AM
> To: Greg Martin
> Cc: ccielab@groupstudy.com
> Subject: Re: IAD 2431 w/ T1 ports and 12.4. Keep getting BERT messages
when
> configuring controller
>
>
>
> one more thought...have you tried physically removing your T1 module and
> replacing it...perhaps to a different slot if you have one available?
>
> On Sun, Jul 13, 2008 at 9:55 AM, Jason Madsen <madsen.jason@gmail.com>
> wrote:
>
> if this issue is on warranted devices, you may want to open a TAC case.
> i'm
> pretty sure many of us would be interested in finding out what the issue
> was, if any, or if it's a bug for that particular IOS and platform.
either
> way, good luck.
>
>
>
> On Sun, Jul 13, 2008 at 3:31 AM, Greg Martin <justler@krweb.net> wrote:
>
> Same here :). I am sure this issue is probably specific to either IADs or
> integrated T1 flex controllers. I've done many 1800 series, and 2800
> series
> with wic-1dsu-T1 and E1 modules and never ran into this :). I'll just run
> 12.3 on it!
>
>
>
> _____
>
> From: Jason Madsen [mailto:madsen.jason@gmail.com]
> Sent: Saturday, July 12, 2008 3:03 PM
> To: Greg Martin
> Cc: ccielab@groupstudy.com
> Subject: Re: IAD 2431 w/ T1 ports and 12.4. Keep getting BERT messages
when
> configuring controller
>
>
>
> that's really weird. i've used T1 modules in 7206s running 12.4 quite a
> bit
> and never had any issues such as this. i don't know what to say.
honestly
> i really prefer to stay away from T1s when i can :-)
>
>
>
>
> On Sat, Jul 12, 2008 at 12:55 PM, Greg Martin <justler@krweb.net> wrote:
>
> Didn't start a BERT test.
>
> This only happens on IOS 12.4. I load 12.3 and it's fine. I can't find
> any
> Cisco documentation to state why this change was made. There are no BERT
> commands under the t1 controller.
>
> The interfaces are integrated and not WIC modules. I've worked w/ BERT
> patterns on channelized OC modules before so i'm familiar with the syntax.
> I just can't figure this one out!
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Jason Madsen
> Sent: Saturday, July 12, 2008 12:48 PM
> To: Greg Martin
> Cc: ccielab@groupstudy.com
> Subject: Re: IAD 2431 w/ T1 ports and 12.4. Keep getting BERT messages
when
> configuring controller
>
> Did you guys start the T-1 BERT? Do a "show run" and look for any "t1
> bert" instances to negate. wish i had a T-1 module to test with really
> quick, but it sounds as though someone started a bert on at least one of
> your t1s. if you can't find the cmd to negate, you might be able to do
> "default" xxx global config' command to restore your t1 controller.
>
> show controllers t1 bert may give you some info' based on the bert if
> you're
> interested.
>
> Jason
>
> On Sat, Jul 12, 2008 at 4:29 AM, Greg Martin <justler@krweb.net> wrote:
>
> > Hey Guys,
> >
> >
> >
> > I've got an IAD 2431 2xT1/E1 router.
> >
> >
> >
> > I'm trying to configure the T1 ports but after I enable the card, I go
> into
> > the T1 controller and do a channel-group 0 timeslots 1-24 speed 64 and I
> > get
> > this message:
> >
> >
> >
> > %LINK-6-BERTMSGS: Configuration not accepted, BERT is running
> >
> >
> >
> > Google'd it and came back with nothing.
> >
> >
> >
> > Running 12.4.18 IP Plus/FW/VOICE
> >
> >
> >
> > Config:
> >
> >
> >
> > card type t1 1
> >
> > !
> >
> > controller t1 1/0
> >
> > framing esf
> >
> > linecode b8zs
> >
> > channel-group 0 timeslots 1-24 speed 64
> >
> >
> >
> > Then it prints:
> >
> >
> >
> > %LINK-6-BERTMSGS: Configuration not accepted, BERT is running
> >
> >
> >
> > It prints this message when I try to modify any commands on the
> controller.
> > I've tried plugging in a loop plug so the bert tests could finish, but
no
> > dice.
> >
> >
> >
> > Can anyone point me in the right direction? I've search over
> cisco.comand
> > i've configured hundreds of wic-1dsu-t1/e1/g703 dsu modules and have
> never
> > run into this...
> >
> >
> >
> > Regards,
> >
> >
> >
> > Greg
> >
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Mon Aug 04 2008 - 06:11:55 ART