From: Anthony Sequeira (Anthony_Sequeira@skillsoft.com)
Date: Sat Jun 28 2008 - 11:30:48 ART
1. In the lab you will end up troubleshooting - that is for sure. It
will either be one of your own configurations that is not quite right,
or it will be something they pre-configured incorrectly. Or - it will be
both! As far as someone's claim that it is always 6 points of built-in
troubleshooting - I say that is a myth. Each lab exam is quite different
from the next.
2. You will not be penalized for "over-configuration". So if I notice
they kind of forgot about an interface and it does not live in a
protocol domain - I would indeed add it to the domain that makes sense -
after asking the proctor about the interface. Be sure that no lab task
actually does give you a clue about what to do with the interface. Also,
be sure not to violate the initial lab instructions, this is often
things like you cannot add interface addressing or static routes.
Anthony J. Sequeira
#15626
www.freeiestuff.com
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
akyccie
Sent: Saturday, June 28, 2008 10:20 AM
To: 'Amir.Tahir/Wateen/Lahore'; 'Almog Ohayon'; ccielab@groupstudy.com
Subject: RE: Real Lab Exam Questions
I would like to add few more points to get clarified here.
1. I have heard there will be 6 marks for troubleshooting like vlan name
defined wrong, interface port is set for half duplex, subnet mask etc
???. I
that true ????
2. IGP full reachability - If they didn't ask to configure any routing
protocols on a particular interface so does it required to redistribute
into
IGP to have full reachability or if you redistribute will loose the
point
because they didn't ask for that.
aky
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Amir.Tahir/Wateen/Lahore
Sent: Wednesday, June 25, 2008 6:36 PM
To: Almog Ohayon; ccielab@groupstudy.com
Subject: RE: Real Lab Exam Questions
Dear Almog,
With reference to your query all I would like to inform you that
Technology won't change. Yes topology defiantly will change lab to lab
but it won't affect you if you prepared the stuff
Secondly, Cisco will give you a clue but at the same time try to confuse
you as well.. If you know the stuff you will analyze what he is trying
to tell u....with do & don't in the Qs
I failed CCIE R&S lab last week only because I did not follow best
practices...Trust me when I saw the lab I know all the stuff but somehow
mess-up due to last min changes in Switching section at 7th hr. Too much
pressure was built up and I was trying to fix the mess I had created for
only 3 marks...
Now we have to ask Experts for best practices.... If Cisco won't ask
you..... you have to do it. One of them is to avoid FR dynamic mapping
on Hub & spoke.... and there will be a lot more to discover....lets put
hands together to find them....
Regards
AT
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Almog Ohayon
Sent: Wednesday, June 25, 2008 4:49 PM
To: ccielab@groupstudy.com
Subject: Real Lab Exam Questions
Hi Everyone,
i have couple of questions for the real lab exam :
1. if in the start of the lab all the trunks are up and the bridging and
switching tasks tell me to configure some of trunks - what to do with
the
rest of the trunks ??
2. how similar is the real ccie lab exam to internetworkexpert Version 4
labs or ipexpert version 9 labs ?
3. if in the tasks frame relay inverse arp is not asked - should i need
to
configure it ??
4. what does it mean speaking devices , transit devices which routers to
refer ??
5. there is no consistent configuration in my training labs
(Internetworkexpert v4) of bgp next-hop-self - when exactly do i need to
configure it ??
-- Best ,Almog Ohayon.
This archive was generated by hypermail 2.1.4 : Tue Jul 01 2008 - 06:23:23 ART