From: Azher Amin (azheramin@gmail.com)
Date: Sun May 25 2008 - 13:20:25 ART
http://www.cisco.com/en/US/docs/ios/12_2/qos/command/reference/qrfcmd4.html#wp1098678
Usage Guidelines
Up to eight IP DSCP values can be matched in one match statement. For
example, if you wanted the IP DCSP values of 0, 1, 2, 3, 4, 5, 6, or 7 (note
that only one of the IP DSCP values must be a successful match criterion,
not all of the specified IP DSCP values), enter the *match ip dscp 0 1 2 3 4
5 6 7* command.
-Azher
On Sun, May 25, 2008 at 7:33 AM, Jonathan Greenwood II <gwood83@gmail.com>
wrote:
> You are correct my mistake had to do a little review myself.
>
> On Sun, May 25, 2008 at 9:21 AM, dara tomar <wish2ie@gmail.com> wrote:
>
> > "The 3rd has the match all which would require it to match CS3 & AF31"
> >
> > We have match-all but only a single condition with multiple dscp values,
> > these would surely OR between all the dscp values supplied.
> >
> >
> > Regards,
> > Dara
> >
> >
> > On Sun, May 25, 2008 at 7:44 PM, Jonathan Greenwood II <
> gwood83@gmail.com>
> > wrote:
> >
> >> I believe the 1st and 2nd examples are correct. The 3rd has the match
> all
> >> which would require it to match CS3 & AF31 which is similar to the 1st
> >> example but you can place them in 1 line.
> >>
> >> On Sun, May 25, 2008 at 9:00 AM, dara tomar <wish2ie@gmail.com> wrote:
> >>
> >>> *I am sure,
> >>>
> >>>
> >>> The first one is incorrect !!!
> >>>
> >>> How can we match two dscp values in a single packet ??
> >>>
> >>> Regards,
> >>> Dara*
> >>>
> >>> On Sun, May 25, 2008 at 6:43 PM, ccievoice1 <ccievoice1@gmail.com>
> >>> wrote:
> >>>
> >>> > YES
> >>> >
> >>> > On Sun, May 25, 2008 at 8:22 PM, Radioactive Frog <
> pbhatkoti@gmail.com
> >>> >
> >>> > wrote:
> >>> >
> >>> > > *Example#1
> >>> > > *Class-map *match-all* test1
> >>> > > match ip dscp CS3
> >>> > > match ip dscp AF31
> >>> > >
> >>> > > result# the test1 class - must match CS3+AF31, otherwise this
> class
> >>> will
> >>> > > not work.
> >>> > >
> >>> > > *Example#2
> >>> > > *Class-map *match-any* test1
> >>> > > match ip dscp CS3
> >>> > > match ip dscp AF31
> >>> > >
> >>> > > result# the test1 class will can match either CS3 or AF31
> >>> > >
> >>> > > *Example#3
> >>> > > *Class-map *match-all* test1
> >>> > > match ip dscp CS3 AF31
> >>> > >
> >>> > > result# the test1 class will can match either CS3 or AF31
> >>> > >
> >>> > > According to my understanding Example 2 and example 3 are the same.
> >>> > >
> >>> > > Am I right?
> >>> > >
> >>> > > -Frog
> >>> > >
> >>> > >
> >>> > >
> >>> _______________________________________________________________________
> >>> > > Subscription information may be found at:
> >>> > > http://www.groupstudy.com/list/CCIELab.html
> >>> >
> >>> >
> >>> >
> _______________________________________________________________________
> >>> > Subscription information may be found at:
> >>> > http://www.groupstudy.com/list/CCIELab.html
> >>>
> >>>
> >>> _______________________________________________________________________
> >>> Subscription information may be found at:
> >>> http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Mon Jun 02 2008 - 06:59:18 ART