From: Narbik Kocharians (narbikk@gmail.com)
Date: Mon May 12 2008 - 22:03:09 ART
One question that you have to ask yourself is "AM I READY? DO I KNOW WHAT I
THINK A CCIE SHOULD KNOW? DO I HAVE THE KNOWLEDGE TO PASS?
If your answers to all questions are "YES 100 percent", then you have done
the right training and you are ready.
What I think you should do is as follows:
Take a section, like Switching, go through the entire 3550/3560
configuration guide, and summarize it, then, do the switching labs from your
vendor and see if you understand it, and know it like the back of your hand,
THIS IS WHY I ALWAYS LIKE THE PROTOCOL SPECIFIC LABS VERSUS THE MOCK LABS. I
DON'T THINK THAT THEY BENEFIT YOU AS MUCH AS PROTOCOL SPECIFIC LABS.
Repeat the same steps for the rest of the protocols, but the trick is to do
one protocol at a time and do not let go until you know it.
After you go through what I just mentioned, you should be ready to do some
Mock labs, you will see that the mock labs are getting easier and easier,
because if you completely know each protocol in the blueprint, WHAT CAN THEY
ASK TO SURPRISE YOU???????? Most of all be honest with yourself.
I want you guys to think about what I am recommending, if it makes sense,
hey, do it, but if it does not make sense, then don't take the
recommendation.
On 5/12/08, Bill Eyer <beyer@optonline.net> wrote:
>
> Brian,
>
> I think you recommended taking one lab and doing it over and over again to
> develop speed, but it wasn't the entire workbook.
>
> Bill
>
> Brian Dennis wrote:
>
> > Carlos,
> > It's not recommended to do all 20 Vol II labs 6 or 7 times. That would
> > be crazy ;-) There are different approaches that we recommend but it is
> > based upon the individual candidate.
> >
> > Brian Dennis, CCIE4 #2210 (R&S/ISP-Dial/Security/SP)
> > bdennis@internetworkexpert.com
> >
> > Internetwork Expert, Inc.
> > http://www.InternetworkExpert.com <http://www.internetworkexpert.com/>
> > Toll Free: 877-224-8987
> > Direct: +1-775-544-1653 (Outside the US and Canada)
> >
> >
> >
> > > ----- Original Message -----
> > >
> > >
> > Subject: Re: what to do next?
> > Date: Mon, May 12, 2008 9:54
> > From: "Carlos Trujillo" <carlos.trujillo.jimenez@gmail.com>
> >
> >
> >
> > > Yes, after finishing a vendor workbook you may know your weak areas,
> > > and do
> > > all once again, but focusing in your weak areas, then its better to
> > > try
> > >
> > >
> > mock
> >
> >
> > > labs.
> > >
> > > Internetworkexpert guys, recommend doing their workbook around 6 or 7
> > >
> > >
> > times!
> >
> >
> > > I think its too much, but it depends in the candidate.
> > >
> > >
> > > 2008/5/11, ahmed badr <eng.ahmedbadr@gmail.com>:
> > >
> > >
> > > > After finishing the WB for one vendor, is it recommended to solve it
> > > > once
> > > > again or go and solve the WB of another vendor?
> > > >
> > > >
> > > >
> > > > _______________________________________________________________________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > > >
> > > >
> > >
> > > _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > >
> >
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
>
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
-- Narbik Kocharians CCSI#30832, CCIE# 12410 (R&S, SP, Security) www.Net-Workbooks.com Sr. Technical Instructor
This archive was generated by hypermail 2.1.4 : Mon Jun 02 2008 - 06:59:16 ART