From: Scott Morris (smorris@ipexpert.com)
Date: Mon Jan 28 2008 - 14:12:52 ARST
If it's already on the local router though, would that help? And would it
be better to know before you leave, or have it happen after you left? :)
_____
From: Ahsan Mohiuddin [mailto:ahsan.mohiuddin@yahoo.com]
Sent: Monday, January 28, 2008 10:56 AM
To: Scott Morris; 'James Wilson'; 'Bill Burns'; 'Monica Belluci'; 'Cisco
certification'
Subject: RE: CCIE LAB - Troubleshooting
will it not be a good idea to pwsd-protect console and tty lines when going
into lunch break? is it allowed?
Scott Morris <smorris@ipexpert.com> wrote:
Did you ask the proctor about it? Could it be anything more entertaining
like kron or eem?
"show run" on all your devices can assist you with that. Checking the logs
can also be good.
Oct 28 20:41:05.025 UTC: %SYS-5-CONFIG_I: Configured from console by console
Oct 28 20:41:05.029 UTC: %HA_EM-5-LOG: eemCfgEvLog: Configuration event
detected
Oct 28 21:09:29.120 UTC: %SYS-5-CONFIG_I: Configured from console by console
Oct 28 21:09:29.120 UTC: %HA_EM-5-LOG: eemCfgEvLog: Configuration event
detected
Or something similar may show up.
An event set could even telnet from one device to another. So if it's on
your equipment, check it out. If it's on a BB device, well... Hmmm...
Read the security section ahead of time and do that first? :)
It's an amusing concept that something like this would be built in, and
certainly no rules against it. But I'd believe this (or self-induced
things) far more than I'd believe the proctor came in to do that...
Just my opinion!
Scott Morris, CCIE4 (R&S/ISP-Dial/Security/Service Provider) #4713, JNCIE-M
#153, JNCIS-ER, CISSP, et al.
CCSI/JNCI-M/JNCI-ER
VP - Technical Training - IPexpert, Inc.
IPexpert Sr. Technical Instructor
A Cisco Learning Partner - We Accept Learning Credits!
Telephone: +1.810.326.1444
Fax: +1.810.454.0130
http://www.ipexpert.com
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
James Wilson
Sent: Sunday, January 27, 2008 3:08 AM
To: Bill Burns; 'Monica Belluci'; 'Cisco certification'
Subject: RE: CCIE LAB - Troubleshooting
When I got back from lunch I found that someone (I assume a proctor) removed
vlan assignments on ports for three routers.
-- James D. Wilson Sr. Network/Security Engineer "non sunt multiplicanda entia praeter necessitatem" William of Ockham (1285-1347/49)-----Original Message----- From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of Bill Burns Sent: Friday, January 25, 2008 8:19 PM To: 'Monica Belluci'; 'Cisco certification' Subject: RE: CCIE LAB - Troubleshooting
Hi Monica,
I would think that #7 is referring to a section later in the lab workbook that might affect an earlier section. If you config XYZ in a section late in the day it could break section ABC that you configured early in the morning. You will get points for XYZ but you will lose your points for ABC. That is why Cisco tells you in tip #1 to read the whole lab. I would doubt that any proctor would break your config while you are at lunch unless you are wearing a Juniper shirt. : )
Thank you,
Bill Burns CCIE #12464, CCSI Rack Time Rentals www.racktimerentals.com
-----Original Message----- From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of Monica Belluci Sent: Thursday, January 24, 2008 8:52 AM To: Cisco certification Subject: CCIE LAB - Troubleshooting
http://www.cisco.com/web/learning/le3/ccie/rs/lab_exam_tips.html
*TEN TIPS FOR TAKING THE LAB EXAM*
1. Read the entire exam first and check for addressing issues. Do not skip any details or sections.
2. Manage your time. Make a plan to cover all the sections in the time provided. Work out how much time you will spend on each section, keeping in mind the point value of the questions. Don't forget to allow time at the end to verify your solutions.
3. Clarify the requirements of each question. Don't assume requirements that aren't mentioned in the question. During the lab, if you are in any doubt, verify your understanding of the question with the proctor.
4. Do each question as a unit. Configure and verify before moving to the next question. You may want to redraw the topology with all the details available. This will help you visualize and map the network.
5. Troubleshoot. You must know how to troubleshoot using the tools available. Although troubleshooting is important, don't lose too much time working on a 2- or 3-point question. If you're caught off-guard by an unfamiliar topic, don't let it absorb too much time. Work on the things you are more comfortable with and go back to difficult items later.
6. Keep a list. During the exam, make notes on configurations and settings as you move through the exam. Make a separate list for items you have not been able to address or where you have not achieved the desired result which you'll need to revisit.
7. Test your work. *Never rely on a configuration done in the early hours of the exam.* *There is a possibility that an item you configured a few sections earlier can become broken and non-functional *. Keep in mind that points are awarded for working configuration only.
8. Save your configurations often.
9. Don't make any drastic changes in the last half hour of the exam.
10. Speed is vital on the exam. Review and practice core material the week before the exam to ensure you can move quickly through the less challenging questions.
Can anyone Understood what Cisco says on 7th tip
Is it engage troubleshooting part which fashioned by CISCO ?
People says you will analyze your configuration difference before BREAK and AFTER break ? Is it ?
I hope, by this email I am not going to break NDA rule.........
**
*What you say?*
Thanks
Monica ** **
This archive was generated by hypermail 2.1.4 : Fri Feb 01 2008 - 10:38:02 ARST