From: Mounir Mohamed (mounir.mohamed@gmail.com)
Date: Sun Jan 27 2008 - 09:09:38 ARST
Sorry forget to say that also u can use the same test to make sure that some
routes are not advertised, also as workaround you can apply the same route
filters to any other interface that connected to internal router (EIGRP
enabled interface) to make sure the filters working fine, it's worst to be
tested durring you lab date.
On Jan 27, 2008 1:06 PM, Mounir Mohamed <mounir.mohamed@gmail.com> wrote:
> Dear Monica,
>
> In such case try to ping one of the BB address sourced by the interface
> you advertising via EIGRP, so now you will be sure that the BB received the
> route and install it on the routing table.
>
> On Jan 27, 2008 12:58 PM, Monica Belluci <mpls1979@gmail.com> wrote:
>
> > thanks for Reply
> > But munir if Router is connected to BB1 .On which we dont have control
> > in exam.And requirement is to send some specifics of routes to
> > backbone .Distribute-list with access-list OUT will send the routes
> > but How can i verify the sending routes to Backbone in EIGRP?
> > Verification .....
> > Thanks
> > Monica
> >
> >
> > On 1/27/08, Mounir Mohamed <mounir.mohamed@gmail.com> wrote:
> > > I tried to catch it with debug IP packet details attached with ACL for
> > > protocol# 88 but nothing appears, but I "Show IP EIGRP topology" on
> > the
> > > origin router will show you the routes that directly connected and
> > > advertised through EIGRP.
> > >
> > >
> > >
> > >
> > >
> > > *Origin Router*
> > >
> > > Rack1R3>show ip eigrp topology
> > >
> > > IP-EIGRP Topology Table for AS(100)/ID(150.1.3.3)
> > >
> > > Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
> > >
> > > r - reply Status, s - sia Status
> > >
> > >
> > >
> > > P 10.3.3.0/24, 1 successors, FD is 128256
> > >
> > > via Connected, Loopback3
> > >
> > > P 10.0.0.0/24, 1 successors, FD is 28160
> > >
> > > via Connected, FastEthernet0/0
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > > *Receiving router*
> > >
> > > Rack1R1#show ip eigrp topology
> > >
> > > IP-EIGRP Topology Table for AS(100)/ID(150.1.1.1)
> > >
> > >
> > >
> > > Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
> > >
> > > r - reply Status, s - sia Status
> > >
> > >
> > >
> > > P 10.3.3.0/24, 1 successors, FD is 156160
> > >
> > > via 10.0.0.3 (156160/128256), FastEthernet0/0
> > >
> > > P 10.0.0.0/24, 1 successors, FD is 28160
> > >
> > > via Connected, FastEthernet0/0
> > >
> > >
> > > On Jan 25, 2008 5:56 PM, Monica Belluci <mpls1979@gmail.com> wrote:
> > >
> > > > If I am running EIGRP with my backbone router .
> > > > How I will come to know that which routes I am going to advertise to
> > > > Backbone ?
> > > > In RIP you can know by Debug ip rip ( Sending update)
> > > > how you will come to know in EIGRP any Debug.
> > > >
> > > > Please suggest
> > > >
> > > > Thanks
> > > > Monica
> > > >
> > > >
> > _______________________________________________________________________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > > >
> > >
> > >
> > >
> > > --
> > > Best Reagrds,
> > > Mounir Mohamed, CCIE #19573
> > >
> >
>
>
>
> --
>
> Best Reagrds,
> Mounir Mohamed, CCIE #19573
>
-- Best Reagrds, Mounir Mohamed, CCIE #19573
This archive was generated by hypermail 2.1.4 : Fri Feb 01 2008 - 10:38:01 ARST