RE: service policy inbound does not work...........

From: subodh.rawat@wipro.com
Date: Sun Jan 20 2008 - 13:27:24 ARST

• Next message: Akhtar Rasool: "Re: Protocol not in the image"
• Previous message: neo: "request for dynamips .net file"
• Maybe in reply to: subodh.rawat@wipro.com: "service policy inbound does not work..........."
• Next in thread: shiran guez: "Re: service policy inbound does not work..........."
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

But IP Precedence is Layer 2.

Thanks
Subodh

________________________________

From: Monica Belluci [mailto:mpls1979@gmail.com]
Sent: Sunday, January 20, 2008 6:19 PM
To: Subodh Singh Rawat (WT01 - TELECOM SERVICE PROVIDER); Cisco
certification
Subject: Re: service policy inbound does not work...........

Hi Subodh,
I implement same scenerio with Dynamips and found same error
%Error: FastEthernet1/8 Service Policy Configuration Failed.Only Police
Action S
upported.
Even though I did not use police command in policy-map .
One thing I marked if I changed port to layer 3 port by "no switchport"
it accept the command.Require more investigation !

Thanks
Monica

On Jan 20, 2008 2:52 PM, <subodh.rawat@wipro.com> wrote:

        Thanks Monica for reply.....I am setting up precedence value to
5. I am neither doing policing nor shaping.

        Pls help.

        Thanks
        Subodh

________________________________

        From: Monica Belluci [mailto:mpls1979@gmail.com]
        Sent: Sunday, January 20, 2008 12:09 PM
        To: Subodh Singh Rawat (WT01 - TELECOM SERVICE PROVIDER); Cisco
certification
        Subject: Re: service policy inbound does not work...........

        Hi Subodh ,

        As per of my Knowledge Police can apply on Inbound as well as
outbound
                                             Shaping can apply only on
outbound .
        Can you re-check are you doing policing rather than shaping ?

        Thanks

        Nalini Roy.

        On Jan 19, 2008 7:03 PM, <subodh.rawat@wipro.com> wrote:

                Hi,

                Can we apply service policy as inbound on 3550 switch?

                This policy map is setting the ip precedence to 5 for
WEB traffic.

                When I applied this on Dynamips (Switch) on inbound at
one of the
                Fastethernet port, it said that only police is allowed
inbound.

                I am asking this question because same scenario is given
in one of the
                CCIE book. However, as far as i have knowledge, we can
not apply any
                queueuing mechanism inbound.

                Thanks
                Subodh

                The information contained in this electronic message and
any attachments to
                this message are intended for the exclusive use of the
addressee(s) and may
                contain proprietary, confidential or privileged
information. If you are not
                the intended recipient, you should not disseminate,
distribute or copy this
                e-mail. Please notify the sender immediately and destroy
all copies of this
                message and any attachments.

                WARNING: Computer viruses can be transmitted via email.
The recipient should
                check this email and any attachments for the presence of
viruses. The company
                accepts no liability for any damage caused by any virus
transmitted by this
                email.

                www.wipro.com <http://www.wipro.com/>

• Next message: Akhtar Rasool: "Re: Protocol not in the image"
• Previous message: neo: "request for dynamips .net file"
• Maybe in reply to: subodh.rawat@wipro.com: "service policy inbound does not work..........."
• Next in thread: shiran guez: "Re: service policy inbound does not work..........."
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

This archive was generated by hypermail 2.1.4 : Fri Feb 01 2008 - 10:38:00 ARST