From: Fang Gao (fanggao@gmail.com)
Date: Sat Jan 12 2008 - 17:47:01 ARST
Try 12.4(13a) IOS. It is the only latest version, which can fit 32M flash.
It solved my problem. I believe it will solve your problem too.
Thanks
On Jan 12, 2008 12:38 PM, Gupta, Gopal (NWCC) <gopal.gupta@hp.com> wrote:
> my router is also 3640 with ver Version 12.4(10a).
>
> Thanks
> Gops
>
> ------------------------------
> *From:* Fang Gao [mailto:fanggao@gmail.com]
> *Sent:* Saturday, January 12, 2008 19:49
> *To:* Gupta, Gopal (NWCC)
> *Cc:* ccielab@groupstudy.com
> *Subject:* Re: OSPF Neighbor Command Issue
>
> Gops,
>
> I had the same problem in 3640 old 12.4 release before. It is an IOS
> bug. I resolved it by downloading newer IOS 12.4 release.
>
> Which IOS release do you have?
>
> HTH
>
> Frank
>
> On Jan 10, 2008 2:00 PM, Gupta, Gopal (NWCC) <gopal.gupta@hp.com> wrote:
>
> > Hi experts,
> >
> > I am facing the issue with OSPF
> > R2 is connected to R3 with Ethernet(Broadcast Mode) and with 2 serial
> > links to R1 (NBMA Mode)
> > i am not allowed to enter neighbor command under the router ospf 1
> >
> > when i give this command :-
> >
> > router ospf 1
> > neighbor 2.2.12.1
> >
> > it gives the error --->
> >
> > "OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> > networks"
> > "OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> > networks"
> >
> > is this the default behavior or i am missing something here????
> >
> > It takes the neighbor command before i give the ethernet link network
> > command. but when i reload it...it again generates the above error
> > message and neighbor commands are automatically removed from the Router
> > ospf configuration...following is the output after i reloaded the Router
> > and it disregarded the neighbor commands.....
> >
> > My question is "does the router not take the neighbor command for NBMA
> > under router ospf, when it has ethernet link also for ospf, on the same
> > router???"
> > I have the following config :---
> >
> > router ospf 1
> > router-id 2.2.2.2
> > log-adjacency-changes
> > network 2.2.2.2 0.0.0.0 area 2
> > network 2.2.12.2 0.0.0.0 area 2
> > network 2.2.12.6 0.0.0.0 area 2
> >
> > neighbor 2.2.12.1 <----------Missing here
> > neighbor 2.2.12.5 <----------Missing here
> >
> > interface Serial2/2
> > ip address 2.2.12.6 255.255.255.252
> > encapsulation frame-relay
> > serial restart-delay 0
> > clock rate 64000
> > frame-relay map ip 2.2.12.5 211 broadcast
> > frame-relay map ip 2.2.12.6 211
> > no frame-relay inverse-arp
> >
> >
> > interface Ethernet0/1
> > ip address 2.2.28.2 255.255.255.0
> > ip pim sparse-dense-mode
> > ip ospf priority 0
> > half-duplex
> > end
> > !
> > interface Serial2/1
> > ip address 2.2.12.2 255.255.255.252
> > encapsulation frame-relay
> > serial restart-delay 0
> > frame-relay map ip 2.2.12.1 201 broadcast
> > frame-relay map ip 2.2.12.2 201
> > no frame-relay inverse-arp
> > end
> >
> > Thanks,
> > Gops
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Feb 01 2008 - 10:37:59 ARST