From: Scott Morris (smorris@ipexpert.com)
Date: Tue Jan 01 2008 - 00:02:03 ARST
I'm more interested in what's up with VLAN 136, whether it's just a timing
thing or what's up. The VLAN is allowed on both trunks and one port SHOULD
be forwarding it unless you have something else going on on switch 3. :)
Show spanning-tree on Cat3. Also "show run | in interface|spanning-tree" to
see what we've done.
From Cat2's perspective, there's something else going on as well. As a root
bridge for all VLANs, you should see all ports as designated.
Perhaps do those two same commands on Cat2 (and Cat1?).
Scott Morris, CCIE4 (R&S/ISP-Dial/Security/Service Provider) #4713, JNCIE-M
#153, JNCIS-ER, CISSP, et al.
CCSI/JNCI-M/JNCI-ER
VP - Technical Training - IPexpert, Inc.
IPexpert Sr. Technical Instructor
A Cisco Learning Partner - We Accept Learning Credits!
Telephone: +1.810.326.1444
Fax: +1.810.454.0130
http://www.ipexpert.com
-----Original Message-----
From: Jeffrey Biggs [mailto:j.biggs@myactv.net]
Sent: Monday, December 31, 2007 8:51 PM
To: 'Scott Morris'; 'Cisco certification'
Subject: RE: IPEXPERT LAB 26: STANDBY Interface on CAT3560
Cat-2#sh int trun
Port Mode Encapsulation Status Native vlan
Fa0/19 on 802.1q trunking 1
Fa0/20 on 802.1q trunking 1
Po12 on 802.1q trunking 1
Port Vlans allowed on trunk
Fa0/19 1-4094
Fa0/20 1-4094
Po12 1-4094
Port Vlans allowed and active in management domain
Fa0/19 1,12,40,100,136,200,300,567
Fa0/20 1,12,40,100,136,200,300,567
Po12 1,12,40,100,136,200,300,567
Port Vlans in spanning tree forwarding state and not pruned
Fa0/19 1
Fa0/20 1,567
Po12 1,12,100,567
Cat-2#
Cat-3#sh int trun
Port Mode Encapsulation Status Native vlan
Fa0/19 on 802.1q trunking 1
Fa0/20 on 802.1q trunking 1
Port Vlans allowed on trunk
Fa0/19 1-4094
Fa0/20 1-4094
Port Vlans allowed and active in management domain
Fa0/19 1,12,40,100,136,200,300,567
Fa0/20 1,12,40,100,136,200,300,567
Port Vlans in spanning tree forwarding state and not pruned
Fa0/19 none
Fa0/20 1,12,40,100,200,300,567
Cat-3#
This one really has me baffled...
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Scott Morris
Sent: Monday, December 31, 2007 3:41 PM
To: 'Jeffrey Biggs'; 'Cisco certification'
Subject: RE: IPEXPERT LAB 26: STANDBY Interface on CAT3560
It would appear that you have no link participating in spanning tree between
Cat3 and other switches.
How does "show interface trunk" look?
Scott Morris, CCIE4 (R&S/ISP-Dial/Security/Service Provider) #4713, JNCIE-M
#153, JNCIS-ER, CISSP, et al.
CCSI/JNCI-M/JNCI-ER
VP - Technical Training - IPexpert, Inc.
IPexpert Sr. Technical Instructor
A Cisco Learning Partner - We Accept Learning Credits!
Telephone: +1.810.326.1444
Fax: +1.810.454.0130
http://www.ipexpert.com
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Jeffrey Biggs
Sent: Monday, December 31, 2007 12:27 PM
To: 'Cisco certification'
Subject: IPEXPERT LAB 26: STANDBY Interface on CAT3560
I have setup the required "standby interface" on the 3560 but for some
reason, the 3560 is not seeing the 3550 (switch 2) as the root. But it is
learning all the vlans via VTP and is forwarding traffic, which really
baffles me. I am running MST on the switches with switch 2 as the root and
switch 1 as the VTP server:
(switch 1)=====po12======(switch 2)-----------Fa0/19 (fa0/20 in
standby)------(switch 3)
All switches running MST and switch 1 sees switch 2 as root, but 3 don't:
Cat-2>sh span
MST0
Spanning tree enabled protocol mstp
Root ID Priority 24576
Address 000e.d799.3f00
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 24576 (priority 24576 sys-id-ext 0)
Address 000e.d799.3f00
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Interface Role Sts Cost Prio.Nbr Type
---------------- ---- --- --------- --------
--------------------------------
Fa0/1 Desg FWD 200000 128.1 P2p
Fa0/6 Desg FWD 200000 128.6 P2p
Fa0/7 Desg FWD 2000000 128.7 P2p
Fa0/8 Desg FWD 2000000 128.8 P2p
Fa0/9 Desg FWD 200000 128.9 P2p
Fa0/12 Desg FWD 2000000 128.12 P2p
Fa0/13 Desg FWD 2000000 128.13 P2p
Fa0/19 Desg FWD 200000 128.19 P2p
Fa0/20 Desg FWD 200000 128.20 P2p
Interface Role Sts Cost Prio.Nbr Type
---------------- ---- --- --------- --------
--------------------------------
Po12 Desg FWD 20000 128.65 P2p
Cat-2>
Cat-3#sh spanning-tree
MST0
Spanning tree enabled protocol mstp
Root ID Priority 32768
Address 0011.bb1c.f000
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768 (priority 32768 sys-id-ext 0)
Address 0011.bb1c.f000
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Interface Role Sts Cost Prio.Nbr Type
---------------- ---- --- --------- --------
--------------------------------
Fa0/5 Desg FWD 200000 128.7 P2p
Cat-3#
This archive was generated by hypermail 2.1.4 : Fri Feb 01 2008 - 10:37:57 ARST