From: srinivas pv (vsrinivas.paturi@gmail.com)
Date: Fri Nov 02 2007 - 07:47:20 ART
Hi,
Please check whether following ans. helps.
Thanks,
Srinivas
========================
Go to univercd
on the network security drop down select "Cisco ASA 5500"
click on "Cisco ASA 5500 Series Adaptive Security Appliance Software"
click on "Version 7.2"
click on "Cisco Security Appliance Command Line Configuration Guide, Version
7.2"
click on "Reference"
click on "Addresses, Protocols, and Ports"
click on "TCP and UDP Ports"
ctrl-f to find the protocol you're looking for
This exact location also has RFC 1918 space if you're suddenly panic'd on
whether or not your memory is exactly right for private address space.
hope this helps,
Dave
============================
On 11/2/07, George Goglidze <goglidze@gmail.com> wrote:
>
> Hi David,
>
> I know the list that comes in access-list command line,
> I didn't need that ones, as I call that well-known ports.
>
> I said telnet, just to say an example in begining, but what I ment was
> SNA,
> SAP and thigs like that.
> you will notice that neither of these come in the list of tcp/udp ports in
> access-list command line.
>
> Thank you very much anyway.
>
> Scott, that was what I needed exactly. not the ESP(50)/AH(51) thing.
>
> Thanks a lot and regards,
>
>
> On 11/2/07, David Prall <dcp@dcptech.com> wrote:
> >
> > If everyone gets use to the command line, and the feel for where things
> > are,
> > IOS can be mastered. It took me less then an hour to get acquainted with
> > IOS
> > XR, and everything is in a different place. I still like J's space
> > completion though.
> >
> > David
> >
> > --
> > http://dcp.dcptech.com
> >
> >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
> > > Behalf Of Scott Vermillion
> > > Sent: Thursday, November 01, 2007 8:37 PM
> > > To: 'David Prall'; 'George Goglidze'; 'Cisco certification'
> > > Subject: RE: doccd question
> > >
> > > Hi David,
> > >
> > > Well, to put it in Joe Brunner parlance, that's why you're a
> > > three-star (or
> > > is it four by now?) general and I'm still a private!
> > >
> > > Thanks much,
> > >
> > > Scott
> > >
> > > -----Original Message-----
> > > From: David Prall [mailto:dcp@dcptech.com]
> > > Sent: Thursday, November 01, 2007 6:11 PM
> > > To: 'Scott Vermillion'; 'George Goglidze'; 'Cisco certification'
> > > Subject: RE: doccd question
> > >
> > > Hell,
> > > conf t
> > > access-list 100 permit ?
> > > <0-255> An IP protocol number
> > > ahp Authentication Header Protocol
> > > eigrp Cisco's EIGRP routing protocol
> > > esp Encapsulation Security Payload
> > > gre Cisco's GRE tunneling
> > > icmp Internet Control Message Protocol
> > > igmp Internet Gateway Message Protocol
> > > ip Any Internet Protocol
> > > ipinip IP in IP tunneling
> > > nos KA9Q NOS compatible IP over IP tunneling
> > > ospf OSPF routing protocol
> > > pcp Payload Compression Protocol
> > > pim Protocol Independent Multicast
> > > tcp Transmission Control Protocol
> > > udp User Datagram Protocol
> > >
> > >
> > > Put the number in and see what "sh access-list 100" displays.
> > > If you are
> > > guessing and sort of have a clue you will be very good to go.
> > >
> > > David
> > >
> > > --
> > > http://dcp.dcptech.com
> > >
> > >
> > > > -----Original Message-----
> > > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
> > > > Behalf Of Scott Vermillion
> > > > Sent: Thursday, November 01, 2007 7:55 PM
> > > > To: 'George Goglidze'; 'Cisco certification'
> > > > Subject: RE: doccd question
> > > >
> > > > I've seen links posted here several times but save yourself a
> > > > few seconds
> > > > and do it from the command line:
> > > >
> > > > 'sh ip port-map' (fairly extensive list) or 'sh ip port-map
> > > > telnet' or 'sh
> > > > ip port-map | inc blah'
> > > >
> > > > I don't think that this works for any IP protocols. In other
> > > > words, if you
> > > > try to do a 'sh ip port-map esp' it isn't going to work, as
> > > > this isn't a
> > > > port number but rather a protocol number. If you needed to
> > > > know that, I
> > > > guess you'd still have to go to the DocCD. But if it was a
> > > > port number I
> > > > was after, I'd try this approach first.
> > > >
> > > > -----Original Message-----
> > > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
> > > > Behalf Of
> > > > George Goglidze
> > > > Sent: Thursday, November 01, 2007 4:48 PM
> > > > To: Cisco certification
> > > > Subject: doccd question
> > > >
> > > > Hi all,
> > > >
> > > > Can anyone tell me please, if you know where on DOCCD can I
> > > > find information
> > > > about application ports.
> > > > for example, ports like telnet, ftp and many other that are
> > > > not well known.
> > > >
> > > > Many thanks,
> > > >
> > > > ______________________________________________________________
> > > > _________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > > >
> > > > ______________________________________________________________
> > > > _________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > > ______________________________________________________________
> > > _________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Dec 01 2007 - 06:37:27 ART