From: WorkerBee (ciscobee@gmail.com)
Date: Fri Oct 26 2007 - 23:49:54 ART
Thanks for the feedback. Yes, I really don't have ILS in all my 03 x
2811 routers.
It seems like getting ILS + HWIC-4ESW-PoE is still more cost effective
than owning 03 x 3560-24-PoE or 03 x 3560-8-PoE switches. I am not
getting the Cat6k so I am using
another router as the branch/hq router.
Is it really worth the trouble to go all out to make ISR inline power
capable? Does the Voice lab really test so much on inline power
configuration? If not, I will probably get some power injector which
is more cost effective.
On 10/27/07, Brian Dennis <bdennis@internetworkexpert.com> wrote:
> Do you have the inline power supply installed or a standard power
> supply? You'll need the inline power supply in addition to the PoE
> daughter card. You can tell what you have by issuing the show power
> inline (if you get output like below you have inline power) or by just
> looking at the back of the 2811. If it's an inline power supply the
> power supply will have a little black phone it.
>
> R1#show power inline
> PowerSupply SlotNum. Maximum Allocated Status
> ----------- -------- ------- --------- ------
> INT-PS 0 160.000 12.600 PS GOOD
> Interface Config Device Powered PowerAllocated
> --------- ------ ------ ------- --------------
> Fa0/1/0 auto Cisco On 6.300 Watts
> Fa0/1/1 auto Cisco On 6.300 Watts
> Fa0/1/2 auto Unknown Off 0.000 Watts
> Fa0/1/3 auto Unknown Off 0.000 Watts
> R1#
>
> HTH,
>
> Brian Dennis, CCIE4 #2210 (R&S/ISP-Dial/Security/SP)
> bdennis@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987
> Direct: 775-852-3995 (Outside the US and Canada)
>
> WorkerBee wrote:
> > Anyone knows how to make this PoE card work? I tried connecting an IP
> > Phone to the port, it shows as down and not supply power to the IP
> > Phone. It is up when I connect to another switch. I am getting rid of
> > 3560-PoE switches for space saving cards instead.
> >
> > I am running 12.4(15)T1 image but under the interface configuration
> > mode, I don't see anything related to command 'power inline....'.
> >
> > I am sure the card is recognize as follows:
> >
> > Yaka#show inventory
> > NAME: "4 Port FE Switch on Slot 0 SubSlot 3", DESCR: "4 Port FE Switch"
> > PID: HWIC-4ESW , VID: VN/A, SN: FOC09453V5Y
> >
> > NAME: "WIC/VIC/HWIC 3 Power Daughter Card", DESCR: "4-Port HWIC-ESW
> > Power Daughter Card"
> > PID: ILPM-4 , VID: VN/A, SN: FOC09454GU0
> >
> >
> > Yaka#show ip int brief
> > Interface IP-Address OK? Method Status
> > Protocol
> > FastEthernet0/3/0 unassigned YES unset up down
> > FastEthernet0/3/1 unassigned YES unset up down
> > FastEthernet0/3/2 unassigned YES unset up down
> > FastEthernet0/3/3 unassigned YES unset up down
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Nov 16 2007 - 13:11:18 ART