From: shiran guez (shiranp3@gmail.com)
Date: Fri Sep 28 2007 - 10:17:06 ART
the only difference between LAN to FR is the LAN is a Broadcast Domain and
FR is NBMA non broadcast domain and when you are using a NBMA you need to do
resolve of Layer 3 to 2 but when working with Point To Point you do not need
to resolve Layer 3 to 2 so the only diff is that you do not support
broadcast.
so I do not think this is a valid explanation bridging is not expecting IP
bridging is layer 2 and is independent from layer 3.
On 9/28/07, hadek.el-ayachi@nsn.com <hadek.el-ayachi@nsn.com> wrote:
>
> I thinks the explanation is that your hub router is expecting IPoLANoFR
> packets, not IPoFR . Hence, you have to enable Bridging in spokes
> routers
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> ext shiran guez
> Sent: vendredi 28 septembre 2007 12:33
> To: Ben
> Cc: Cisco certification
> Subject: Re: Bridging over FR
>
> Thanks Ben, but what is the explanation to this?
>
> as i see it when I bridge the 2 interface together why do i need to
> include also the other side of the serial link on the bridging in
> Broadcast Domain like Ethernet I do not need to do it so why in NBMA
> with Point to Point as it should not have a problem with Layer 3 to 2
> resolution.
>
>
>
>
> On 9/28/07, Ben <bmunyao@gmail.com> wrote:
> >
> >
> >
> > Hi Shiran,
> >
> > You need to use "bridge irb" on R2/R3, and move the IP addresses from
> > the serial interfaces to BVIs. That way, and with "bridge-group ..."
> > on the serial interface, it will work.
> >
> > HTH
> >
> > Ben
> >
> > On 9/28/07, shiran guez <shiranp3@gmail.com> wrote:
> >
> > > R3-------
> > > |-----R1
> > > R2-------
> > >
> > >
> > > R1 is used as FR Hub for R2 and R3
> > > I am trying to set R1 as Bridge between R2 and R3 I used R1 /2/3
> > > Point to Point Interface
> > >
> > > R1
> > >
> > >
> > > !
> > > interface Serial1/0
> > > no ip address
> > > encapsulation frame-relay
> > > no ip route-cache
> > > serial restart-delay 0
> > > !
> > > interface Serial1/0.1 point-to-point no ip route-cache frame-relay
> > > interface-dlci 102 bridge-group 1 !
> > > interface Serial1/0.2 point-to-point no ip route-cache frame-relay
> > > interface-dlci 103 bridge-group 1 no ip routing bridge 1 protocol
> > > ieee end
> > >
> > > R1#sh bridge 1 group
> > >
> > > Bridge Group 1 is running the IEEE compatible Spanning Tree protocol
> > >
> > > Port 12 (Serial1/0.1 Frame Relay) of bridge group 1 is forwarding
> > > Port 13 (Serial1/0.2 Frame Relay) of bridge group 1 is forwarding
> > >
> > > R1#sh spanning-tree 1 brief
> > >
> > > Bridge group 1
> > > Spanning tree enabled protocol ieee
> > > Root ID Priority 32768
> > > Address 0000.0c45.dae8
> > > This bridge is the root
> > > Hello Time 2 sec Max Age 20 sec Forward Delay 15
> sec
> > >
> > > Bridge ID Priority 32768
> > > Address 0000.0c45.dae8
> > > Hello Time 2 sec Max Age 20 sec Forward Delay 15
> sec
> > > Aging Time 300
> > >
> > > Interface Designated
> > > Name Port ID Prio Cost Sts Cost Bridge
> > > ID Port
> > > ID
> > > -------------------- ------- ---- ----- --- -----
> --------------------
> > > -------
> > > Serial1/0.1 128.12 128 647 FWD 0 32768
> 0000.0c45.dae8
> > > 128.12
> > > Serial1/0.2 128.13 128 647 FWD 0 32768
> 0000.0c45.dae8
> > > 128.13
> > >
> > > R2
> > >
> > > R2#sh run int ser1/0.1
> > > Building configuration...
> > >
> > > Current configuration : 119 bytes
> > > !
> > > interface Serial1/0.1 point-to-point
> > > ip address 182.158.123.2 255.255.255.0
> > > frame-relay interface-dlci 201
> > >
> > > R3
> > >
> > > R3#sh run int ser1/0.1
> > > Building configuration...
> > >
> > > Current configuration : 119 bytes
> > > !
> > > interface Serial1/0.1 point-to-point
> > > ip address 182.158.123.3 255.255.255.0
> > > frame-relay interface-dlci 301
> > >
> > > but I do not understand why i cant ping between R2 to R3 as it look
> like
> > > the
> > > bridge is FWD and working ok all the interface are point to point so
> > > there
> > > should not be a encapsulation error of resolving layer 2 to 3 or
> layer 2
> > > to
> > > 2 on the bridge
> > >
> > > R2#debug ip packet detail
> > > IP packet debugging is on (detailed)
> > > R2#ping 182.158.123.3 re 1
> > >
> > > Type escape sequence to abort.
> > > Sending 1, 100-byte ICMP Echos to 182.158.123.3, timeout is 2
> seconds:
> > >
> > > *Mar 1 00:36: 11.215: IP: tableid=0, s=182.158.123.2 (local), d=
> > > 182.158.123.3 (Serial1/0.1), routed via FIB
> > > *Mar 1 00:36:11.219: IP: s= 182.158.123.2 (local),
> > > d=182.158.123.3(Serial1/0.1), len 100, sending
> > > *Mar 1 00:36:11.219: ICMP type=8, code=0.
> > > Success rate is 0 percent (0/1)
> > >
> > >
> > >
> > > R3#debug ip packet detail
> > > IP packet debugging is on (detailed)
> > > R3#ping 182.158.123.2 re 1
> > >
> > > Type escape sequence to abort.
> > > Sending 1, 100-byte ICMP Echos to 182.158.123.2, timeout is 2
> seconds:
> > >
> > > *Mar 1 00:36: 57.651: IP: tableid=0, s=182.158.123.3 (local), d=
> > > 182.158.123.2 (Serial1/0.1), routed via FIB
> > > *Mar 1 00:36:57.655: IP: s= 182.158.123.3 (local),
> > > d=182.158.123.2(Serial1/0.1), len 100, sending
> > > *Mar 1 00:36:57.655: ICMP type=8, code=0.
> > > Success rate is 0 percent (0/1)
> > >
> > > so you see there is no problem sending on both sides
> > >
> > > also I am getting on the DLCI 0x4242 Spaning tree frames
> > >
> > > R3#debug frame-relay packet
> > > Frame Relay packet debugging is on
> > > *Mar 1 00:40:34.571: Serial1/0(i): dlci 301(0x48D1), pkt type
> 0x4242,
> > > datagramsize 39
> > > R3#
> > > *Mar 1 00:40:40.575: Serial1/0(i): dlci 301(0x48D1), pkt type
> 0x4242,
> > > datagramsize 39
> > > R3#
> > > *Mar 1 00:40:42.571: Serial1/0(i): dlci 301(0x48D1), pkt type
> 0x4242,
> > > datagramsize 39
> > > R3#
> > >
> > >
> > >
> > > I am missing here something stupid for sure
> > >
> > >
> > > --
> > > Shiran Guez
> > > MCSE CCNP NCE1
> > > http://cciep3.blogspot.com
> > >
> > >
> _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> > >
> >
> >
>
>
> --
> Shiran Guez
> MCSE CCNP NCE1
> http://cciep3.blogspot.com
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
-- Shiran Guez MCSE CCNP NCE1 http://cciep3.blogspot.com
This archive was generated by hypermail 2.1.4 : Sat Oct 06 2007 - 12:01:16 ART