From: Wisit Phatchoo (Wisit.P@dcs.premier.co.th)
Date: Mon Sep 24 2007 - 03:26:30 ART
Dear Eric
I got it, Thank you very much for your advice.
Best regards
Wisit
________________________________
From: Eric Leung [mailto:eric.lwc@gmail.com]
Sent: Sunday, September 23, 2007 11:20 PM
To: Wisit Phatchoo
Cc: Joseph Brunner; ccielab@groupstudy.com
Subject: Re: Difference between "police" and "police cir"
Hi Wisit,
When you take a closer look to the command reference, "police cir" can
be used to specify a 2-rate token bucket policing, i.e. the conforming
bucket and exceeding bucket rates are not the same. For "police" command
only, the 2 buckets are operating with the same rate.
police -
http://www.cisco.com/univercd/cc/td/doc/product/software/ios124/124cr/hq
os_r/qos_o1h.htm#wp1084068
police cir pir -
http://www.cisco.com/univercd/cc/td/doc/product/software/ios124/124cr/hq
os_r/qos_o1h.htm#wp1084420
<http://www.cisco.com/univercd/cc/td/doc/product/software/ios124/124cr/h
qos_r/qos_o1h.htm#wp1084068>
HTH,
Eric.
- Thanks for the question coz I can learn more.
2007/9/24, Wisit Phatchoo <Wisit.P@dcs.premier.co.th>:
Dear Joseph
I see no difference; these means both two commands are same, do I
understand correct?
-----------------------------------
policy-map Test2
class class-default
police cir 1000000
policy-map Test1
class class-default
police 1000000
interface Ethernet1/2
ip address 2.2.2.2 255.255.255.0
half-duplex
ipv6 enable
ipv6 ospf 1 area 1
service-policy input Test1
!
interface Ethernet1/3
ip address 3.3.3.3 255.255.255.0
half-duplex
ipv6 enable
ipv6 ospf 1 area 0
service-policy input Test2
R1#sh policy-map interface e1/2
Ethernet1/2
Service-policy input: Test1
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
police:
cir 1000000 bps, bc 31250 bytes
conformed 0 packets, 0 bytes; actions:
transmit
exceeded 0 packets, 0 bytes; actions:
drop
conformed 0 bps, exceed 0 bps
R1#sh policy-map interface e1/3
Ethernet1/3
Service-policy input: Test2
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
police:
cir 1000000 bps, bc 31250 bytes
conformed 0 packets, 0 bytes; actions:
transmit
exceeded 0 packets, 0 bytes; actions:
drop
conformed 0 bps, exceed 0 bps
Best regards
Wisit Phatchoo
-----Original Message-----
From: Joseph Brunner [mailto: joe@affirmedsystems.com]
Sent: Sunday, September 23, 2007 10:45 PM
To: Wisit Phatchoo; ccielab@groupstudy.com
Subject: RE: Difference between "police" and "police cir"
Lab it up...
Verify with show policy-map int sX/X
Do some home work for us...
-----Original Message-----
From: nobody@groupstudy.com [mailto: nobody@groupstudy.com
<mailto:nobody@groupstudy.com> ] On Behalf Of
Wisit Phatchoo
Sent: Monday, September 24, 2007 1:44 AM
To: ccielab@groupstudy.com
Subject: Difference between "police" and "police cir"
Dear All
I have some confused about how different between "police" and "police
cir" command under policy map. Can anyone tell me please? Thank you very
much.
Best regards
Wisit
This archive was generated by hypermail 2.1.4 : Sat Oct 06 2007 - 12:01:15 ART