From: Tony Schaffran (groupstudy@cconlinelabs.com)
Date: Sat Aug 25 2007 - 07:29:35 ART
If your R5 fa1/1 is physically connected to SW2 fa0/5, then I would say you
are looking at a cable issue.
Have you swapped the Ethernet cable between the two devices?
Tony Schaffran
Network Analyst
CCIE #11071
CCNP, CCNA, CCDA,
NNCDS, NNCSS, CNE, MCSE
www.cconlinelabs.com
Your #1 choice for online Cisco rack rentals.
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
NITIN NITIN
Sent: Friday, August 24, 2007 3:47 PM
To: groupstudy@cconlinelabs.com; ccielab@groupstudy.com
Subject: RE: ethernet link not comming up
Hi ,
again same issue
SW2#sh run int fastEthernet 0/5
Building configuration...
Current configuration : 110 bytes
!
interface FastEthernet0/5
no switchport
ip address 150.100.3.4 255.255.255.0
speed 100
duplex full
end
R5#sh run int fastEthernet 1/1
Building configuration...
Current configuration : 95 bytes
!
interface FastEthernet1/1
ip address 150.100.3.1 255.255.255.0
duplex full
speed 100
end
FastEthernet1/0 110.1.145.5 YES NVRAM up
down
FastEthernet1/1 150.100.3.1 YES manual up
down
Loopback0 110.1.5.1 YES NVRAM up
up
R5#
SW2 line protocol up
R5 down
doing on real routers
R5-----------SW2
Regards
Tony Schaffran <groupstudy@cconlinelabs.com> wrote:
I see that you do not have an IP address configured on your router
interface.
Could that be a problem?
Tony Schaffran
Network Analyst
CCIE #11071
CCNP, CCNA, CCDA,
NNCDS, NNCSS, CNE, MCSE
www.cconlinelabs.com
Your #1 choice for online Cisco rack rentals.
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
NITIN NITIN
Sent: Monday, August 20, 2007 7:19 AM
To: ccielab@groupstudy.com
Subject: ethernet link not comming up
Hi ,
I have a issue which i strange for me
R5 fa1/0--------------F0/5 -SW1
R5#sh run int fa 1/0
Building configuration...
Current configuration : 72 bytes
!
interface FastEthernet1/0
no ip address
duplex full
speed 100
end
R5#sh isp inh it p inbrt br | i| i 1/10
/0
FastEthernet1/0 unassigned YES NVRAM up
down<<<
SW1#sh run int fa 0/5
Building configuration...
Current configuration : 110 bytes
!
interface FastEthernet0/5
switchport access vlan 2005
switchport mode access
speed 100
duplex full
end
SW1#sh ip int brief | i 0/5
FastEthernet0/5 unassigned YES unset up
up<<<<<<<
If I shut interface on R5 =====
R5(config-if)#
*Aug 20 14:10:58.411: %LINK-5-CHANGED: Interface FastEthernet1/0, changed
state to administratively down
port on SW1 goes down 0-=-----
Aug 20 14:10:14: %LINK-3-UPDOWN: Interface FastEthernet0/5, changed state
to down
Regard
---------------------------------
Choose the right car based on your needs. Check out Yahoo! Autos new Car
Finder tool.
This archive was generated by hypermail 2.1.4 : Sat Sep 01 2007 - 11:32:13 ART