From: Julian Rodriguez (jumaroyu@gmail.com)
Date: Sat Aug 11 2007 - 09:14:53 ART
Thanks Brian,
But that's not it, I verified it again, here you go:
BB2#sh run | in CISCO $
BB2#
12:44:22: RIP: sending v2 update to 224.0.0.9 via FastEthernet0/24 (
192.10.1.8)
12:44:22: RIP: build update entries - suppressing null update
Rack1SW2#
12:44:50: RIP: sending v2 update to 224.0.0.9 via FastEthernet0/24 (
192.10.1.8)
12:44:50: RIP: build update entries - suppressing null update
Rack1SW2#sh run | in RIP $
Rack1SW2#sh run | in $
12:47:09: RIP: sending v2 update to 224.0.0.9 via FastEthernet0/24 (
192.10.1.8)
12:47:09: RIP: build update entries - suppressing null update
Rack1SW2#sh run | in CISCO $
Rack1SW2#
On 8/10/07, Brian Dennis <bdennis@internetworkexpert.com> wrote:
>
> As an FYI you can also accidently put a space on the end of the key chain
> name when it's applied to an interface. This will of course cause problems.
>
>
> Rack4R1(config-if)#ip rip authentication key-chain RIP <-- no space added
> Rack4R1(config-if)#do sho run | in RIP $
> Rack4R1(config-if)#do sho run | in RIP$
> key chain RIP
> ip rip authentication key-chain RIP
> Rack4R1(config-if)#ip rip authentication key-chain RIP <-- space added
> Rack4R1(config-if)#do sho run | in RIP$
> key chain RIP
> Rack4R1(config-if)#do sho run | in RIP $
> ip rip authentication key-chain RIP
> Rack4R1(config-if)#
>
>
> Brian Dennis, CCIE4 #2210 (R&S/ISP-Dial/Security/SP)
> *bdennis@internetworkexpert.com*** <bdennis@internetworkexpert.com>
>
>
> Internetwork Expert, Inc.
> *http://www.InternetworkExpert.com*** <http://www.internetworkexpert.com/>
> Toll Free: 877-224-8987
> Direct: 775-745-6404 (Outside the US and Canada)
>
>
>
> On Aug 10, 2007, at 2:13 PM, Julian Rodriguez wrote:
>
> On 8/10/07, Julian Rodriguez <jumaroyu@gmail.com> wrote:
>
>
>
> Answers between lines...
>
>
>
>
> On 8/10/07, Jorge Martinez <jorge_bgp@yahoo.com> wrote:
>
>
>
> Hello Julian,
>
>
> - have you tried getting rid on both sides of the
> authentication over RIP?
>
>
>
>
>
> Yes I did, same result
>
>
> - have you tried using a different key-string on both
>
> sides, just as a test?
>
>
>
>
>
> Yes, did that too, using plain text mode as well.
>
>
> Sometimes one leave a space at the end of the password
>
> and that will also be counted as a character ...
>
>
>
>
>
> that was the first test, no luck.
>
>
>
>
>
> Hope any of this clues can help you ...
>
>
>
>
> --- Julian Rodriguez < jumaroyu@gmail.com> wrote:
>
>
>
> This one has been killing me for the past couple of
> days, I am working on
> IEWB Core Lab 1 Task 4.5, following are the configs
> on both BB2 and SW2,
> which are supposed to use md5 to exchange RIP. I
> verified the solution
> because I couldn't find out what the problem was,
> can't see the RIP routes
> on SW2 anyways, but to my surprise my config was
> exactly what the solution
> stated. Any clues? I really don't see a way to put
> the routes into SW2
> routing table without changing the current config.
>
>
> BB2:
>
>
> interface FastEthernet0/0
> description Ethernet to SW2 Fa0/24
> ip address 192.10.1.254 255.255.255.0
> ip rip authentication mode md5
> ip rip authentication key-chain RIP
> duplex auto
> speed auto
> ipv6 address 2001:192:10:1::254/64
> ipv6 rip RIPng enable
> ipv6 ospf 1 area 0
>
>
>
>
> key chain RIP
> key 1
> key-string CISCO
>
>
> SW2:
>
>
> interface Vlan82
> ip address 192.10.1.8 255.255.255.0
> ip rip authentication mode md5
> ip rip authentication key-chain RIP
>
>
> interface FastEthernet0/24
> switchport access vlan 82
>
>
> key chain RIP
> key 1
> key-string CISCO
>
>
>
>
> Troubleshooting OUPUTS:
>
>
>
>
> Rack1SW2#ping 192.10.1.254
>
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 192.10.1.254 ,
> timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip
> min/avg/max = 1/2/8 ms
> Rack1SW2#
>
>
> Rack1SW2#
> 01:19:04: RIP: sending v2 update to 224.0.0.9 via
> Vlan82 ( 192.10.1.8)
> 01:19:04: RIP: build update entries - suppressing
> null update
> Rack1SW2#
> 01:19:32: RIP: sending v2 update to 224.0.0.9 via
> Vlan82 (192.10.1.8)
> 01:19:32: RIP: build update entries - suppressing
> null update
> Rack1SW2#
> Mar 1 01:25:45.707: %TCP-6-BADAUTH: No MD5 digest
> from 192.10.1.8(179) to
> 192.10.1.254(14382) (RST)
> Mar 1 01:25:49.707: %TCP-6-BADAUTH: No MD5 digest
> from 192.10.1.8(179) to
> 192.10.1.254(14382) (RST)
> Mar 1 01:25: 57.499: RIP: sending v2 update to
> 224.0.0.9 via
> FastEthernet0/0 ( 192.10.1.254)
> Mar 1 01:25:57.499: RIP: build update entries -
> suppressing null update
>
>
>
>
>
> _______________________________________________________________________
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> ____________________________________________________________________________________
> Yahoo! oneSearch: Finally, mobile search
> that gives answers, not web links.
> http://mobile.yahoo.com/mobileweb/onesearch?refer=1ONXIC
>
>
>
>
>
>
>
>
>
> --
> MCSE-MCSA 2K & 2K3: Security-Messaging
> MCDST, MCDBA, MCT, CEH, CISSP
> CCNA, CCSP, CNA 6, CCA, HP MASE
> Server+, I-Net+, Security+, Network+, A+
>
>
>
>
>
>
>
>
>
> --
> MCSE-MCSA 2K & 2K3: Security-Messaging
> MCDST, MCDBA, MCT, CEH, CISSP
> CCNA, CCSP, CNA 6, CCA, HP MASE
> Server+, I-Net+, Security+, Network+, A+
>
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
-- MCSE-MCSA 2K & 2K3: Security-Messaging MCDST, MCDBA, MCT, CEH, CISSP CCNA, CCSP, CNA 6, CCA, HP MASE Server+, I-Net+, Security+, Network+, A+
This archive was generated by hypermail 2.1.4 : Sat Sep 01 2007 - 11:32:10 ART