From: Serhat Aslan (serhatworks@gmail.com)
Date: Fri Aug 10 2007 - 14:38:14 ART
I check the bug again, and "p-t-mp nb" it doesn't work either, and you can
find the bug id, case issue, etc.. last weeks archives.
On 8/10/07, NITIN NITIN <ccie_study_123@yahoo.com> wrote:
>
> CAN ANYBODY ALSO CONFIRM IS THIS BUG ANY ONE FACED ,
> COZ MY BACBONE NOT COMING UP DUE TO THIS
>
> Regard
>
> *Serhat Aslan <serhatworks@gmail.com>* wrote:
>
> One of the previous letters (probably last week) written about this
> problem.
> * An active "ip ospf non-broadcast" + "virtual-link" statement, after
> that applying a neighbor statement had been rejected, due to ios bug.
> * AFAIK, when using p-t-mp nonbroadcast, neighbor statement hasn't give
> any error.
>
> Serhat Aslan
>
>
> On 8/10/07, NITIN NITIN < ccie_study_123@yahoo.com> wrote:
> >
> > Hi ,
> >
> > Thanks for havving a look --
> >
> > COMMANDS ASKED ARE PASTED BELOW
> >
> >
> > interface Serial2/0
> > ip address 190.1.135.3 255.255.255.0
> > encapsulation frame-relay
> > ip ospf network point-to-multipoint non-broadcast
> > serial restart-delay 0
> > no frame-relay inverse-arp IP 302
> > no frame-relay inverse-arp IP 304
> > no frame-relay inverse-arp IP 311
> > no frame-relay inverse-arp IP 312
> > no frame-relay inverse-arp IP 314
> > no frame-relay inverse-arp IP 315
> > !
> >
> > Rack1R3# sh ip ospf interface serial 2/0
> > Serial2/0 is up, line protocol is up
> > Internet Address 190.1.135.3/24, Area 135
> > Process ID 1, Router ID 150.1.3.3, Network Type POINT_TO_MULTIPOINT,
> > Cost: 64
> > Transmit Delay is 1 sec, State POINT_TO_MULTIPOINT,
> > Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5
> > oob-resync timeout 120
> > Hello due in 00:00:13
> > Index 1/7, flood queue length 0
> > Next 0x0(0)/0x0(0)
> > Last flood scan length is 0, maximum is 0
> > Last flood scan time is 0 msec, maximum is 0 msec
> > Neighbor Count is 0, Adjacent neighbor count is 0
> > Suppress hello for 0 neighbor(s)
> >
> > router ospf 1
> > router-id 150.1.3.3
> > log-adjacency-changes
> > area 34 nssa no-summary
> > area 135 virtual-link 150.1.5.5 authentication message-digest
> > area 135 virtual-link 150.1.5.5 message-digest-key 1 md5 CISCO
> > area 135 virtual-link 150.1.1.1 authentication message-digest
> > area 135 virtual-link 150.1.1.1 message-digest-key 1 md5 CISCO
> > redistribute rip subnets
> > network 150.1.3.3 0.0.0.0 area 0
> > network 190.1.34.3 0.0.0.0 area 34
> > network 190.1.135.3 0.0.0.0 area 135
> >
> >
> >
> > MY ISSUE BEFORE GOING TO AUTHENTICATION IS COMING IS NOW IN
> > NEIGHBOURSHIP
> >
> > I PUT NEIGHBOUR COMMAND ROUTER SAYS
> >
> > Rack1R3(config-router)# neighbor 190.1.135.5
> > > OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> > > networks
> >
> > AND WHEN I PUT NEIGHBOUR COMMNAD AND
> > network 190.1.135.3 0.0.0.0 area 135
> >
> > ROUTER TAKES IT
> >
> > after putting rest commands in router ospf neighbor command get
> > removed
> >
> > PLEASE SUGGEST , STUCK SINCE WHOLE DAY
> >
> >
> >
> > Regard
> >
> > Herbert Maosa < asawilunda@googlemail.com> wrote:
> > Can you send a dump of
> >
> > show run interface < the-trouble-some-interface >. as well as a dump of
> > show ip ospf interface < the-trouble-some-interface >
> >
> >
> >
> > Herbert.
> >
> >
> > On 8/10/07, NITIN NITIN wrote:
> > >
> > > Hi experts,
> > >
> > > PLEASE SUGGEST BADLY STUCK IN A ISSUE ......
> > >
> > >
> > > I'm trying OPSF AUTHENTICATION on SERIAL INT
> > >
> > > WITH TWO DIFFRENT KEYS FOR SPOKES
> > >
> > >
> > > ON physican int I have given
> > >
> > > ip ospf network point-to-multipoint non-broadcast
> > >
> > > still it gives me error when putting
> > >
> > >
> > > Rack1R3(config-router)# neighbor 190.1.135.1
> > > OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> > > networks<<<<
> > > Rack1R3(config-router)# neighbor 190.1.135.5
> > > OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> > > networks
> > >
> > >
> > > ALSO -- WHEN I
> > >
> > > see
> > > SH IP OSPF INT SE 2/0
> > >
> > > I SEE ONLY YOUNG KEY as 35
> > >
> > > NO ROLBACK KEY 13 <<<<<<<<<<<<<<<<<<
> > >
> > >
> > > HUB ROUTER R3----
> > >
> > >
> > > Enter configuration commands, one per line. End with CNTL/Z.
> > > Router(config)#version 12.3
> > > Router(config)#service timestamps debug datetime msec
> > > Router(config)#service timestamps log datetime msec
> > > Router(config)#no service password-encryption
> > > Router(config)#!
> > > Router(config)#hostname Rack1R3
> > > Rack1R3(config)#!
> > > Rack1R3(config)#boot-start-marker
> > > Rack1R3(config)#boot-end-marker
> > > Rack1R3(config)#!
> > > Rack1R3(config)#enable password cisco
> > > Rack1R3(config)#!
> > > Rack1R3(config)#no aaa new-model
> > > Rack1R3(config)#ip subnet-zero
> > > Rack1R3(config)#!
> > > Rack1R3(config)#!
> > > Rack1R3(config)#no ip domain lookup
> > > Rack1R3(config)#!
> > > Rack1R3(config)#ip cef
> > > Rack1R3(config)#!
> > > Rack1R3(config)#!
> > > Rack1R3(config)#key chain RIP
> > > Rack1R3(config-keychain)# key 1
> > > Rack1R3(config-keychain-key)# key-string CISCO
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#!
> > > Rack1R3(config-keychain-key)#interface Loopback0
> > > Rack1R3(config-if)# ip address 150.1.3.3 255.255.255.0
> > > Rack1R3(config-if)#!
> > > Rack1R3(config-if)#
> > > Rack1R3(config-if)#!
> > > Rack1R3(config-if)#interface FastEthernet0/0
> > > Rack1R3(config-if)# ip address 192.10.1.3 255.255.255.0
> > > Rack1R3(config-if)# ip rip authentication mode md5
> > > Rack1R3(config-if)# ip rip authentication key-chain RIP
> > > Rack1R3(config-if)# duplex full
> > > Rack1R3(config-if)#!
> > > Rack1R3(config-if)#interface FastEthernet1/0
> > > Rack1R3(config-if)# ip address 190.1.3.3 255.255.255.0
> > > Rack1R3(config-if)# duplex auto
> > > Rack1R3(config-if)# speed auto
> > > Rack1R3(config-if)#!
> > > Rack1R3(config-if)#interface FastEthernet1/1
> > > Rack1R3(config-if)# no ip address
> > > Rack1R3(config-if)# shutdown
> > > Rack1R3(config-if)# duplex auto
> > > Rack1R3(config-if)# speed auto
> > > Rack1R3(config-if)#!
> > > Rack1R3(config-if)#interface Serial2/0
> > > Rack1R3(config-if)# ip address 190.1.135.3 255.255.255.0
> > > Rack1R3(config-if)# encapsulation frame-relay
> > > Rack1R3(config-if)# ip ospf authentication message-digest
> > > Rack1R3(config-if)# ip ospf message-digest-key 13 md5 CISCO13
> > > Rack1R3(config-if)# ip ospf message-digest-key 35 md5 CISCO35
> > > Rack1R3(config-if)# ip ospf network point-to-multipoint non-broadcast
> > > Rack1R3(config-if)# serial restart-delay 0
> > > Rack1R3(config-if)# no frame-relay inverse-arp IP 302
> > > Rack1R3(config-if)# no frame-relay inverse-arp IP 304
> > > Rack1R3(config-if)# no frame-relay inverse-arp IP 311
> > > Rack1R3(config-if)# no frame-relay inverse-arp IP 312
> > > Rack1R3(config-if)# no frame-relay inverse-arp IP 314
> > > Rack1R3(config-if)# no frame-relay inverse-arp IP 315
> > > Rack1R3(config-if)#!
> > > Rack1R3(config-if)#interface Serial2/1
> > > Rack1R3(config-if)# no ip address
> > > Rack1R3(config-if)# encapsulation frame-relay
> > > Rack1R3(config-if)# serial restart-delay 0
> > > Rack1R3(config-if)# frame-relay interface-dlci 314 ppp
> > Virtual-Template1
> > > Rack1R3(config-fr-dlci)# no frame-relay inverse-arp
> > > Rack1R3(config-if)#!
> > > Rack1R3(config-if)#interface Serial2/2
> > > Rack1R3(config-if)# no ip address
> > > Rack1R3(config-if)# shutdown
> > > Rack1R3(config-if)# serial restart-delay 0
> > > Rack1R3(config-if)#!
> > > Rack1R3(config-if)#interface Serial2/3
> > > Rack1R3(config-if)# no ip address
> > > Rack1R3(config-if)# shutdown
> > > Rack1R3(config-if)# serial restart-delay 0
> > > Rack1R3(config-if)#!
> > > Rack1R3(config-if)#interface Virtual-Template1
> > > Rack1R3(config-if)# ip address 190.1.34.3 255.255.255.0
> > > Rack1R3(config-if)# no peer neighbor-route
> > > Rack1R3(config-if)#!
> > > Rack1R3(config-if)#router ospf 1
> > > Rack1R3(config-router)# router-id 150.1.3.3
> > > Rack1R3(config-router)# log-adjacency-changes
> > > Rack1R3(config-router)# area 34 nssa no-summary
> > > Rack1R3(config-router)#$irtual-link 150.1.5.5 authentication
> > > message-digest
> > > Rack1R3(config-router)#$irtual-link 150.1.5.5 message-digest-key 1 md5
> > > CISCO
> > > Rack1R3(config-router)#$irtual-link 150.1.1.1 authentication
> > > message-digest
> > > Rack1R3(config-router)#$irtual-link 150.1.1.1 message-digest-key 1 md5
> > > CISCO
> > > Rack1R3(config-router)# redistribute rip subnets
> > > Rack1R3(config-router)# network 150.1.3.3 0.0.0.0 area 0
> > > Rack1R3(config-router)# network 190.1.34.3 0.0.0.0 area 34
> > > Rack1R3(config-router)# network 190.1.135.3 0.0.0.0 area 135
> > > Rack1R3(config-router)# neighbor 190.1.135.1
> > > OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> > > networks<<<<
> > > Rack1R3(config-router)# neighbor 190.1.135.5
> > > OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> >
> > > networks
> > > Rack1R3(config-router)#!
> > > Rack1R3(config-router)#router rip
> > > Rack1R3(config-router)# version 2
> > > Rack1R3(config-router)# passive-interface default
> > > Rack1R3(config-router)# redistribute os 1 route-map OSPF>>RIP
> > > Rack1R3(config-router)# no passive-interface FastEthernet0/0
> > > Rack1R3(config-router)# no passive-interface FastEthernet1/0
> > > Rack1R3(config-router)# network 190.1.0.0
> > > Rack1R3(config-router)# network 192.10.1.0
> > > Rack1R3(config-router)# default-information originate route-map DR
> > > Rack1R3(config-router)# distribute-list 122 in FastEthernet0/0
> > > Rack1R3(config-router)# no auto-summary
> > > Rack1R3(config-router)#!
> > > Rack1R3(config-router)#ip classless
> > > Rack1R3(config)#no ip http server
> > > Rack1R3(config)#!
> > > Rack1R3(config)#!
> > > Rack1R3(config)#!
> > > Rack1R3(config)#ip prefix-list /24 seq 5 permit 190.1.0.0/24
> > > Rack1R3(config)#$ 122 deny ip host 192.10.1.254 222.22.2.0 0.0.0.255
> > > Rack1R3(config)#$ 122 permit ip host 192.10.1.253 222.22.2.0 0.0.0.255
> >
> > > Rack1R3(config)#access-list 122 deny ip host 192.10.1.253 any
> > > Rack1R3(config)#access-list 122 permit ip any any
> > > Rack1R3(config)#!
> > > Rack1R3(config)#route-map DR permit 10
> > > Rack1R3(config-route-map)# set interface FastEthernet0/0
> > > Rack1R3(config-route-map)#!
> > > Rack1R3(config-route-map)#route-map OSPF>>RIP permit 10
> > > Rack1R3(config-route-map)# match ip address prefix-list /24
> > > Rack1R3(config-route-map)# set metric 10
> > > Rack1R3(config-route-map)#!
> > > Rack1R3(config-route-map)#route-map OSPF>>RIP permit 20
> > > Rack1R3(config-route-map)# set metric 1
> > > Rack1R3(config-route-map)#!
> > > Rack1R3(config-route-map)#!
> > > Rack1R3(config-route-map)#!
> > > Rack1R3(config-route-map)#!
> > > Rack1R3(config-route-map)#!
> > > Rack1R3(config-route-map)#!
> > > Rack1R3(config-route-map)#!
> > > Rack1R3(config-route-map)#gatekeeper
> > > Rack1R3(config-gk)# shutdown
> > > Rack1R3(config-gk)#!
> > > Rack1R3(config-gk)#!
> > > Rack1R3(config-gk)#line con 0
> > > Rack1R3(config-line)# exec-timeout 0 0
> > > Rack1R3(config-line)# privilege level 15
> > > Rack1R3(config-line)# logging synchronous
> > > Rack1R3(config-line)# stopbits 1
> > > Rack1R3(config-line)#line aux 0
> > > Rack1R3(config-line)# exec-timeout 0 0
> > > Rack1R3(config-line)# privilege level 15
> > > Rack1R3(config-line)# stopbits 1
> > > Rack1R3(config-line)#line vty 0 4
> > > Rack1R3(config-line)# password cisco
> > > Rack1R3(config-line)# login
> > > Rack1R3(config-line)#!
> > > Rack1R3(config-line)#!
> > > Rack1R3(config-line)#end
> > > Rack1R3#
> > >
> > >
> > >
> > >
> > >
> > > ---------------------------------
> > > Be a better Globetrotter. Get better travel answers from someone who
> > > knows.
> > > Yahoo! Answers - Check it out.
> > >
> > >
> > _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> > >
> >
> >
> >
> > --
> > Kindest regards,
> > hm
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> >
> > ---------------------------------
> > Be a better Heartthrob. Get better relationship answers from someone who
> > knows.
> > Yahoo! Answers - Check it out.
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
>
>
> ------------------------------
> Yahoo! oneSearch: Finally, mobile search that gives answers<http://us.rd.yahoo.com/evt=48252/*http://mobile.yahoo.com/mobileweb/onesearch?refer=1ONXIC>,
> not web links.
>
> ------------------------------
> Be a better Globetrotter. Get better travel answers
> <http://us.rd.yahoo.com/evt=48254/*http://answers.yahoo.com/dir/_ylc=X3oDMTI5MGx2aThyBF9TAzIxMTU1MDAzNTIEX3MDMzk2NTQ1MTAzBHNlYwNCQUJwaWxsYXJfTklfMzYwBHNsawNQcm9kdWN0X3F1ZXN0aW9uX3BhZ2U-?link=list&sid=396545469>from
> someone who knows.
> Yahoo! Answers - Check it out.
This archive was generated by hypermail 2.1.4 : Sat Sep 01 2007 - 11:32:10 ART