From: Farrukh Haroon (farrukhharoon@gmail.com)
Date: Mon Jul 30 2007 - 10:11:37 ART
why don't you put the following command on all voice ports:
caller-id alerting dsp-pre-allocate
also see debug voip ccapi inout (or something similar) to check if you are
getting CLI from provider
On 7/29/07, Kayode Oladipo <kayoladipo@hotmail.com> wrote:
>
> Viny,
>
> From the show diag, you're using a generation 2 VIC that's VIC2-4FXO which
> supports caller-ID.
>
> For caller-ID to be supported on the older VICs, you would require the
> VIC-2FXO-M1 or M2 as the case maybe.
>
> I believe the problem you're having is from the PSTN provider. Confirm if
> the
> PSTN is sending caller-ID.
>
> Regards,
>
> Kayode
>
>
>
> > Date: Sun, 29 Jul 2007 23:47:04 +0800> From: wilfred_thegr8@yahoo.co.in>
> Subject: Re: FXO Caller ID prb> To: vinygm@gmail.com> CC:
> ccielab@groupstudy.com> > I guess so...> > Wilfred> > viny gm
> <vinygm@gmail.com> wrote: i am not in US I am in Dubai, Still i need M1 or
> M2
> ??> > Viny> > > On 7/29/07, wilfred d'souza <wilfred_thegr8@yahoo.co.in>
> wrote: Your card will not support Caller ID. you need to have VIC-2FXO-M1
> if
> in US.> > Wilfred> > viny gm <vinygm@gmail.com> wrote: > Here is show
> diag> >
> 2nd generation - FXO Voice daughter card (4 port)> Hardware Revision : 5.0
> >
> Top Assy. Part Number : 800-21589-02> Board Revision : A0> Deviation
> Number :
> 0-0> Fab Version : 04 > PCB Serial Number : FOC10440NZ9> RMA Test History
> :
> 00> RMA Number : 0-0-0-0> RMA History : 00> Product (FRU) Number :
> VIC2-4FXO>
> Version Identifier : V01> CLEI Code : CNUIAPRAAA> EEPROM format version 4>
> EEPROM contents (hex):> 0x00: 04 FF 40 00 4C 41 05 00 C0 46 03 20 00 54 55
> 02>
> 0x10: 42 41 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31> 0x20: 30 34 34 30
> 4E 5A
> 39 03 00 81 00 00 00 00 04 00 > 0x30: CB 89 56 49 43 32 2D 34 46 58 4F 89
> 56
> 30 31 20> 0x40: C6 8A 43 4E 55 49 41 50 52 41 41 41 FF FF FF FF> 0x50: FF
> FF
> FF FF FF FF FF FF FF FF FF FF FF FF FF FF> 0x60: FF FF FF FF FF FF FF FF
> FF FF
> FF FF FF FF FF FF > 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF>
> >
> viny> > > On 7/29/07, wilfred d'souza <wilfred_thegr8@yahoo.co.in > wrote:
> can
> u also paste the show diag?> > viny gm < vinygm@gmail.com> wrote: Debug
> error
> msg> ----------------------> get_fxo_caller_id:Caller ID receive failed.
> parseCallerIDString:no data.> > > > config> --------------> voice-port
> 0/1/0>
> cptone GB> timeouts call-disconnect 3> timeouts wait-release 3> connection
> plar opx 300> impedance complex2> caller-id enable> !> voice-port 0/1/1>
> cptone GB> timeouts call-disconnect 3> timeouts wait-release 3> connection
> plar opx 300> impedance complex2> caller-id enable> !> voice-port 0/1/2>
> cptone GB> timeouts call-disconnect 3> timeouts wait-release 3> connection
> plar opx 300> impedance complex2> caller-id enable> !> voice-port 0/1/3>
> cptone GB> timeouts call-disconnect 3> timeouts wait-release 3> connection
> plar opx 300> impedance complex2> caller-id alerting dsp-pre-allocate> > >
> dial-peer voice 200 voip> tone ringback alert-no-PI> translation-profile
> outgoing addinPrefix> preference 1> destination-pattern 3..> voice-class
> h323
> 1> session target ipv4:xx.xx.xx.xx> dtmf-relay h245-alphanumeric> codec
> g711ulaw> no vad> > dial-peer voice 100 pots> preference 1>
> destination-pattern 9[2-9]......> port 0/1/0> !> dial-peer voice 101 pots>
> destination-pattern 9[2-9]......> port 0/1/1> !> dial-peer voice 102 pots>
> destination-pattern 9[2-9]......> port 0/1/2> !> dial-peer voice 103 pots>
> destination-pattern 9[2-9]......> > Viny> > > On 7/29/07, wilfred d'souza
> <wilfred_thegr8@yahoo.co.in > wrote: Also your FXO Interface needs to be
> VIC-2FXO-M1 or VIC-2FXO-M2 for Caller ID Support. > > Wilfred> > Mark Snow
> <msnow@ipexpert.com> wrote: Two things - 1 are you using MGCP? While the
> gateway clearly does > support Caller ID and FXO, CallManager only
> supports it
> through H323 > signaling. Also be sure that your FXO port has the
> "caller-id
> enable" > config on it.> > Mark Snow> Sr Technical Instructor> IPexpert,
> Inc.>
> > Sent from my iPhone> > On Jul 29, 2007, at 7:00 AM, "viny gm" wrote: > >
> >
> Hi,> >> >> >> > I am getting a problem regarding caller id my FXO port is
> not
> > > forwarding the> > caller id to IP phone. When I am using same phone
> line
> with analog > > phone the > > caller id is coming on that> >> >> >> > Can
> any
> body help on this regards> >> >> >> > Viny> >> >
> _______________________________________________________________________ >
> > >
> > Subscription information may be found at:> >
> http://www.groupstudy.com/list/CCIELab.html > >
> _______________________________________________________________________>
> Subscription information may be found at: >
> http://www.groupstudy.com/list/CCIELab.html> > > >
> ---------------------------------> Yahoo! Movies - Search movie info and
> celeb
> profiles and photos. > > > > > > > --------------------------------->
> Yahoo!
> Movies - Search movie info and celeb profiles and photos. > > > > > > > >
> >
> ---------------------------------> > Real people. Real questions. Real
> answers. Share what you know. > > > > > > >
> --------------------------------->
> Yahoo! Movies - Search movie info and celeb profiles and photos.> >
> _______________________________________________________________________>
> Subscription information may be found at: >
> http://www.groupstudy.com/list/CCIELab.html
> _________________________________________________________________
> See what you re getting into before you go there.
> http://newlivehotmail.com
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Aug 18 2007 - 08:17:42 ART