From: Edouard Zorrilla (ezorrilla@tsf.com.pe)
Date: Thu Jun 21 2007 - 12:51:36 ART
Thanks David,
I have reimaged using a CD and now I just see one interface, the others are
not now.
bash-2.05b# ifconfig
ge0_1 Link encap:Ethernet HWaddr 00:0F:1F:65:8C:8C
inet addr:200.48.241.119 Bcast:200.48.241.127
Mask:255.255.255.128
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:252 errors:0 dropped:0 overruns:0 frame:0
TX packets:292 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:25490 (24.8 KiB) TX bytes:276956 (270.4 KiB)
Base address:0xdcc0 Memory:feb20000-feb40000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.255.255.255
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:308 (308.0 B) TX bytes:308 (308.0 B)
-bash-2.05b#
Please let me know if you overcome this problem,
Thanks a lot,
Regards
----- Original Message -----
From: "David Mitchell" <david.mitchell@centientnetworks.com>
To: "Edouard Zorrilla" <ezorrilla@tsf.com.pe>; "CCIE 2 B"
<doubleccie@yahoo.com>; "Steve Rue" <steve@ruehome.org>;
<ccielab@groupstudy.com>; <security@groupstudy.com>
Sent: Wednesday, June 20, 2007 2:54 PM
Subject: RE: upgrading IPS 4235
> FYI, I have tried to upgrade two 4215 units from 4.x to 5.x and I got
> this message each time. The install docs even tell you that you may get
> this message, and if you do you just need to wait.
>
> However, in both of my cases I waited over an hour and this message
> never went away. Rebooted several times, disabled the virtual sensors
> and all interfaces, and it still never went away. In both cases I had
> to re-image the sensor on 5.x to get it at that level of code.
>
> I'm about to do another one and I really don't want to re-image it due
> to a lot of complex filters that I would have to rebuild. So if you
> figure out a solution please let me know!
>
> David Mitchell
> #17178
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Edouard Zorrilla
> Sent: Wednesday, June 20, 2007 12:34 PM
> To: CCIE 2 B; Steve Rue; ccielab@groupstudy.com; security@groupstudy.com
> Subject: Re: upgrading IPS 4235
>
> Hello Sir,
>
> I keep getting a error when I try to upgrade to the major version, the
> message that I get is:
> "Error: AnalysisEngine is currently busy and unable to process this
> update.
> Please wait several minutes before attempting update again"
>
> What I am doing is the next:
> ---------------------------------------------------------
> sensor(config)# upgrade
> ftp://cisco@200.48.241.51//IPS-K9-maj-5.0-1e-S149.rpm.pkg
> Password: *****
> Warning: Executing this command will apply a major version upgrade to
> the
> application partition. The system may be rebooted to complete the
> upgrade.
> Continue with upgrade? : yes
> Error: AnalysisEngine is currently busy and unable to process this
> update.
> Please wait several minutes before attempting update again.
>
> ---------------------------------------------------------
>
> Please let me know if you get this message as well and if so how do you
> overcome this problem. Thanks in advance,
>
> Best Regards
>
> ----- Original Message -----
> From: "CCIE 2 B" <doubleccie@yahoo.com>
> To: "Steve Rue" <steve@ruehome.org>; <ccielab@groupstudy.com>;
> <security@groupstudy.com>
> Sent: Sunday, May 13, 2007 4:11 AM
> Subject: RE: upgrading IPS 4235
>
>
>> thanks a lot ..that was it !!!
>>
>> im running 5.1 peacefully now
>>
>>
>>
>> Steve Rue <steve@ruehome.org> wrote:
>> Is there any reason you can't (or don't want to) upgrade
> incrementally,
>> from 4.1, then to 5.0, then to 5.1? This would at least solve your
>> problem of a bad boot cdrom.
>>
>>
> http://www.cisco.com/univercd/cc/td/doc/product/iaabu/csids/csids11/5020
>> _02.htm#wp1043779
>>
>> http://www.cisco.com/cgi-bin/tablebuild.pl/ips5
>> download IPS-K9-maj-5.0-1e-S149.rpm.pkg and go from there.
>>
>> -----Original Message-----
>> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
>> CCIE 2 B
>> Sent: Saturday, May 12, 2007 9:15 PM
>> To: ccielab@groupstudy.com; security@groupstudy.com
>> Subject: upgrading IPS 4235
>>
>> folks ;
>> I have an IPS 4235 running 4.1 and i wonder how can i upgrade that box
>> to 5.1 ..on the software page of CCO there is only one file .ISO
>> available for 4235 which i do not know how to use .
>>
>> do I need to have the recovery image CD ?? if yes can anyone help me
>> to get it offline
>>
>> thanks
>>
>>
>>
>> ---------------------------------
>> No need to miss a message. Get email on-the-go
>> with Yahoo! Mail for Mobile. Get started.
>>
>>
> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>> ---------------------------------
>> 8:00? 8:25? 8:40? Find a flick in no time
>> with theYahoo! Search movie showtime shortcut.
>>
>>
> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sun Jul 01 2007 - 17:24:50 ART