From: Sadiq Yakasai (sadiqtanko@gmail.com)
Date: Tue Jun 05 2007 - 04:50:38 ART
Thanks Guys,
Its actually the image that doesnt support OSPF, but ive downloaded
the EMI and doing an upgrade in a bit actually.
As for Nagendra, just to clarify to you; I had Vlan interfaces
configured already, as I know the ospf process needs an ip add to
acquire the router-id from at least...
On 6/5/07, Dat Nguyen <DatN@fpt.com.vn> wrote:
>
> Hic hic,
> Please Check the image of your switch, standard image not support OSFP.
>
> Best regards,
> Nguyen Dat
>
> ________________________________
> From: nobody@groupstudy.com on behalf of nagendra kumar
> Sent: Tue 6/5/2007 10:30 AM
> To: Sadiq Yakasai; Mark Mckillop (mmckillo)
> Cc: Shamin; Cisco certification
> Subject: Re: RIP question
>
>
>
>
> HI Sadiq,
>
> Check if you have any interface up with address configured. If not, you
> wont be able to enable ospf.
>
> 3660(config)#router ospf 1
> 3660(config)#int lo0
> 3660(config-if)#ip addr 1.1.1.1 255.0.0.0
> 3660(config-if)#no shut
> 3660(config-if)#exit
> 3660(config)#router ospf 1
> 3660(config-router)#
>
> Regards,
> Nagendra
>
> Sadiq Yakasai <sadiqtanko@gmail.com> wrote: hmmmm, guys,
>
> so, whats the reason i cant enable router ospf on a 3560 switch please?
>
> see dump below:
>
> SW2#conf t
> Enter configuration commands, one per line. End with CNTL/Z.
> SW2(config)#ip routing
> SW2(config)#router ospf 1
> SW2(config)#router rip
> SW2(config-router)#exit
> SW2(config)#router ospf 1
> SW2(config)#router ospf 1
> SW2(config)#
>
>
> Could this be a bug or what? it just wont go into router config mode
> for ospf but it does for rip........
>
> Thanks
>
> On 6/3/07, Sadiq Yakasai wrote:
> > so what does it do instead?
> >
> > could it be a configured alias?
> >
> > On 6/3/07, Mark Mckillop (mmckillo) wrote:
> > > Try adding a network statement that covers an interface and you might
> > > see it magically appear in the config.
> > >
> > > Mark.
> > >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> > > Shamin
> > > Sent: 03 June 2007 13:50
> > > To: Cisco certification
> > > Subject: RIP question
> > >
> > > Hi All,
> > >
> > > I have a question regarding rip.
> > > IIs there a way in the ios on routers to disable the command "router
> > > rip"
> > > where in the prompt
> > > does not go into the config-router mode. IP routing is enabled in any
> > > case.
> > > Or to put it in a different way, What would be the reason , when you
> > > enter the "router rip" command in the IOS , it does not go into the
> > > config-router mode even when Ip routing is enabled.
> > >
> > > Regards
> > > Shamin
> > >
> > >
> _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > >
> _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
> ---------------------------------
> Fussy? Opinionated? Impossible to please? Perfect. Join Yahoo!'s user panel
> and lay it on us.
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sun Jul 01 2007 - 17:24:46 ART