From: Sadiq Yakasai (sadiqtanko@gmail.com)
Date: Tue May 29 2007 - 18:38:28 ART
Kim,
yeah, thats correct. I was only tryin to replicate "ccie anees"'s
scenario anyways...
I also tried it with EIGRP running, thinking if spli horizon might be
his culprit but it works fine as well...
not sure whats up with his setup...thnks for the points anyway, noted!
Sadiq
On 5/29/07, Kim <support@isolvesystems.com> wrote:
> Sadiq,
> I think you can use just one virtual-template on R5. It will create two
> virtual-access interface.
>
> I ran into some issues doing it your way when I configured OSPF.
>
> Kim
>
>
>
>
> On 5/29/07, Sadiq Yakasai <sadiqtanko@gmail.com> wrote:
> > i tried it again and this time ur way, and it works fine!
> > see below my config:
> > R1---------\
> > \
> > /-----------R5
> > R2---------/
> >
> >
> -------------------------------------------------------------------------------------------------------------
> > R5#sh run
> > hostname R5
> > !
> > interface Serial0/1/0
> > no ip address
> > encapsulation frame-relay
> > frame-relay interface-dlci 501 ppp Virtual-Template1
> > frame-relay interface-dlci 502 ppp Virtual-Template2
> > !
> > interface Virtual-Template1
> > ip address 192.168.1.5 255.255.255.0
> > !
> > interface Virtual-Template2
> > ip address 192.168.1.5 255.255.255.0
> >
> > end
> >
> --------------------------------------------------------------------------------------------------
> >
> > R1#sh run
> > Building configuration...
> >
> > interface Serial0/1/0
> > no ip address
> > encapsulation frame-relay
> > frame-relay interface-dlci 105 ppp Virtual-Template1
> > !
> > interface Virtual-Template1
> > ip address 192.168.1.1 255.255.255.0
> > !
> > end
> >
> > R1#
> >
> >
> ---------------------------------------------------------------------------------------------------
> > R2#sh run
> > Building configuration...
> >
> > interface Serial0/1/0
> > no ip address
> > encapsulation frame-relay
> > frame-relay interface-dlci 205 ppp Virtual-Template1
> > !
> > interface Virtual-Template1
> > ip address 192.168.1.2 255.255.255.0
> > !
> > end
> >
> > R2#
> >
> >
> >
> -----------------------------------------------------------------------------------------------------
> > Successful Pings!!
> >
> > R2#ping 192.168.1.1
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
> > !!!!!
> > Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms
> >
> > R2#ping 192.168.1.5
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 192.168.1.5, timeout is 2 seconds:
> > !!!!!
> > Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms
> >
> >
> > I think u need to check ur other spoke router's config!!
> >
> > HTH
> >
> > Sadiq
> >
> >
> > On 5/29/07, Sadiq Yakasai <sadiqtanko@gmail.com> wrote:
> > >
> > > hey there,
> > >
> > > dont u need to configure another dlci's on the two spoke routers,
> pointing to each other?
> > >
> > > I tried that and it seems to work fine.
> > >
> > >
> > >
> > > On 5/29/07, ccie anees < ccieanees@yahoo.com> wrote:
> > > > I have an issue in pinging between spoke routers.
> > > > R3 is a hub router.
> > > >
> > > > ------ R1
> > > > |
> > > > R3 ---
> > > > |
> > > > ------ R5
> > > >
> > > > R3
> > > > interface Serial1/0
> > > > no ip address
> > > > encapsulation frame-relay IETF
> > > > frame-relay interface-dlci 301 ppp Virtual-Template13
> > > > frame-relay interface-dlci 305 ppp Virtual-Template35
> > > > no frame-relay inverse-arp
> > > > !
> > > > interface Virtual-Template13
> > > > ip address 167.1.135.3 255.255.255.0
> > > > !
> > > > interface Virtual-Template35
> > > > ip address 167.1.135.3 255.255.255.0
> > > > !
> > > > router eigrp 10
> > > > network 167.1.135.3 0.0.0.0
> > > > no auto-summary
> > > > eigrp router-id 150.1.3.3
> > > > R1
> > > > interface Serial0/0
> > > > no ip address
> > > > encapsulation frame-relay
> > > > frame-relay interface-dlci 103 ppp Virtual-Template13
> > > > no frame-relay inverse-arp
> > > > !
> > > > interface Virtual-Template13
> > > > ip address 167.1.135.1 255.255.255.0
> > > > !
> > > > router eigrp 10
> > > > network 167.1.135.1 0.0.0.0
> > > > no auto-summary
> > > > eigrp router-id 150.1.1.1
> > > >
> > > > R5
> > > > interface Serial0/0
> > > > no ip address
> > > > encapsulation frame-relay IETF
> > > > frame-relay interface-dlci 503 ppp Virtual-Template35
> > > > no frame-relay inverse-arp
> > > > !
> > > > interface Virtual-Template35
> > > > ip address 167.1.135.5 255.255.255.0
> > > > !
> > > > router eigrp 10
> > > > network 167.1.135.5 0.0.0.0
> > > > no auto-summary
> > > > eigrp router-id 150.1.5.5
> > > >
> > > > Result:
> > > > R3:
> > > > Rack1R3#ping 167.1.135.1
> > > > Type escape sequence to abort.
> > > > Sending 5, 100-byte ICMP Echos to 167.1.135.1, timeout is 2 seconds:
> > > > !!!!!
> > > > Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60
> ms
> > > > Rack1R3#ping 167.1.135.5
> > > > Type escape sequence to abort.
> > > > Sending 5, 100-byte ICMP Echos to 167.1.135.5, timeout is 2 seconds:
> > > > !!!!!
> > > > Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/60
> ms
> > > > Rack1R3#
> > > >
> > > > Problem:
> > > > R5
> > > >
> > > > Rack1R5#ping 167.1.135.3
> > > > Type escape sequence to abort.
> > > > Sending 5, 100-byte ICMP Echos to 167.1.135.3, timeout is 2 seconds:
> > > > !!!!!
> > > > Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/60
> ms
> > > > Rack1R5#
> > > >
> > > > Rack1R5#ping 167.1.135.1
> > > > Type escape sequence to abort.
> > > > Sending 5, 100-byte ICMP Echos to 167.1.135.1, timeout is 2 seconds:
> > > > .....
> > > > Success rate is 0 percent (0/5)
> > > >
> > > >
> > > > ---------------------------------
> > > > Luggage? GPS? Comic books?
> > > > Check out fitting gifts for grads at Yahoo! Search.
> > > >
> > > >
> _______________________________________________________________________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
>
>
>
> --
> http://www.isolvesystems.com
This archive was generated by hypermail 2.1.4 : Fri Jun 01 2007 - 06:55:22 ART