From: Dennis Worth (Dennis.Worth@oomc.com)
Date: Fri May 04 2007 - 17:42:36 ART
Check LMI
Dennis Worth
Network Engineer
Option One Mortgage
Phone 949-790-3687
dennis.worth@oomc.com
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Kim
Sent: Friday, May 04, 2007 11:53 AM
To: Brian Dennis
Cc: premkumar somasundaram; ccielab@groupstudy.com
Subject: Re: Frame relay back to back
I use dynamips to do the same lab for back to back frame-relay. I had
no
keepalive configured. The interface was up for a while and R5's
interface
went down for the following reason. R4 interface stays up and the PVC
Status says STATIC. Any idea why the PVC for R5 is deleted?
DLCI = 111, DLCI USAGE = LOCAL, PVC STATUS = DELETED, INTERFACE =
Serial1/1.101
input pkts 621 output pkts 29 in bytes 95864
out bytes 3594 dropped pkts 0 in pkts dropped
0
out pkts dropped 0 out bytes dropped 0
in FECN pkts 0 in BECN pkts 0 out FECN pkts 0
out BECN pkts 0 in DE pkts 0 out DE pkts 0
out bcast pkts 28 out bcast bytes 3498
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
pvc create time 00:55:46, last time pvc status changed 00:03:41
On 4/28/07, Brian Dennis <bdennis@internetworkexpert.com> wrote:
>
> This link should help:
>
> http://www.internetworkexpert.com/resources/backtoback-framerelay.htm
>
> --
>
> Brian Dennis, CCIE4 #2210 (R&S/ISP-Dial/Security/SP)
> bdennis@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987
> Direct: 775-745-6404 (Outside the US and Canada)
>
>
>
>
> On 4/28/07 9:23 AM, "premkumar somasundaram"
> <premkumar.somasundaram@gmail.com> wrote:
>
> > Group ,
> > When I am configuring frame relay back to back over the serial
> connection,
> > the link stays up for 30 odd seconds and it goes down. R4 & R5 are
> > connected via serial link and I would like to configure frame relay
back
> to
> > back over that . Here is the configuration....
> >
> > R4
> >
> > interface Serial2/1
> > no ip address
> > encapsulation frame-relay
> > !
> > interface Serial2/1.1 point-to-point
> > ip address 145.1.45.4 255.255.255.0
> > frame-relay interface-dlci 111
> >
> > R5
> > interface Serial2/1
> > no ip address
> > encapsulation frame-relay
> > clock rate 64000
> > no dce-terminal-timing-enable
> > !
> > interface Serial2/1.1 point-to-point
> > ip address 145.1.45.5 255.255.255.0
> > frame-relay interface-dlci 111
> >
> >
> > Am I missing some thing here..
> >
> >
> > Thanks in advance.
> > prem
> >
> >
This archive was generated by hypermail 2.1.4 : Fri Jun 01 2007 - 06:55:20 ART