From: Edward Norton (doubleccie@yahoo.com)
Date: Mon Apr 23 2007 - 08:55:46 ART
thanks for all the replies .
the route has 64/16 mem
the router just works fine when i run 12.2(40a) IP/IDS/FW/IPSEC software (file name is c3620-ik9o3s-mz.122-40a.bin)
while when i run 12.2T (c3620-ik9o3s-mz.122-11.T11.bin ) or 12.3 (c3620-ik9o3s7-mz.123-22.bin) it does not recongnize my WIC-2T card as well the two 2FE port do not ping anywhere !!
I have attached the whole boot process , as you can see the two serial are not recognized at all , while the two FE are not responding to any pings .
i noticed that the Rommon is an early release and thought that some upgrade might help ...im also not sure to identify if the card is v2 or v1
any more inputs will be appreciated .
thanks
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3620-IK9O3S-M), Version 12.2(11)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Wed 14-Apr-04 22:06 by hqluong
Image text-base: 0x6000891C, data-base: 0x6186A000
Compliance with U.S. Export Laws and Regulations - Encryption
This product performs encryption and is regulated for export
by the U.S. Government.
This product is not authorized for use by persons located
outside the United States and Canada that do not have prior
approval from Cisco Systems, Inc. or the U.S. Government.
This product may not be exported outside the U.S. and Canada
either by physical or electronic means without PRIOR approval
of Cisco Systems, Inc. or the U.S. Government.
Persons outside the U.S. and Canada may not re-export, resell,
or transfer this product by either physical or electronic means
without prior approval of Cisco Systems, Inc. or the U.S.
Government.
cisco 3620 (R4700) processor (revision 0x81) with 60416K/5120K bytes of memory.
Processor board ID 07019400
R4700 CPU at 80Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
DRAM configuration is 32 bits wide with parity disabled.
29K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
interface Serial0/0
^
% Invalid input detected at '^' marker.
no ip address
% Incomplete command.
shutdown
% Incomplete command.
no fair-queue
^
% Invalid input detected at '^' marker.
clock rate 2000000
^
% Invalid input detected at '^' marker.
interface Serial0/1
^
% Invalid input detected at '^' marker.
no ip address
% Incomplete command.
shutdown
% Incomplete command.
clock rate 2000000
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:09.695: %FECPM-3-TDMSW: TDM switch init in slot 0 failed
-Traceback= 60214020 6020E890 604A0690 604A0780 6045CEE4 60389508 603896F0 60439E60 60439E
4C
*Mar 1 00:00:09.699: %FECPM-1-INITFAIL: NM slot 0: PCI dev 5 init failed
*Mar 1 00:00:09.807: %FECPM-1-DISCOVER: NM slot 0: only 2 PCI dev found
*Mar 1 00:00:14.103: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar 1 00:00:14.103: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
00:00:15: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state t
o down
00:00:15: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state t
o down
00:00:16: %SYS-5-CONFIG_I: Configured from memory by console
00:00:19: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3620-IK9O3S-M), Version 12.2(11)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986
R2#
R2#-2004 by cisco Systems, Inc.
Compiled Wed 14-Apr-04 22:06 by hqluong
00:00:19: %SNMP-5-COLDSTART: SNMP agent on host R2 is undergoing a cold start
00:00:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state t
o up
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#
R2#show ver
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3620-IK9O3S-M), Version 12.2(11)T11, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Wed 14-Apr-04 22:06 by hqluong
Image text-base: 0x6000891C, data-base: 0x6186A000
ROM: System Bootstrap, Version 11.1(17)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc2)
ROM: 3600 Software (C3620-IK9O3S-M), Version 12.2(11)T11, RELEASE SOFTWARE (fc1)
R2 uptime is 0 minutes
System returned to ROM by power-on
System image file is "flash:c3620-ik9o3s-mz.122-11.T11.bin"
cisco 3620 (R4700) processor (revision 0x81) with 60416K/5120K bytes of memory.
Processor board ID 07019400
R4700 CPU at 80Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
DRAM configuration is 32 bits wide with parity disabled.
29K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
R2#
R2#show inte f0/0
FastEthernet0/0 is up, line protocol is down
Hardware is AmdFE, address is 0010.7b04.8701 (bia 0010.7b04.8701)
Internet address is 10.1.1.2/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto Speed, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
7 packets output, 420 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Darby Weaver <darbyweaver@yahoo.com> wrote:
Interesting problem.
I have 6 of these little fellows.
As I recall the upgrade you may require will be in the
form of a physical chip, not necessarily a software
upgrade per se.
And also check your NM-Modules - are the V2 or are
they older.
I'd suspect they are V2 and while they may be
supported in the 3620, I'd wager they are not.
Let me know.
As I said I still own 6 and might to upgrade myself.
--- Edward Norton wrote:
> guys ;
> I have a 3620 it has 2 FE and 2Serial cards.
> the funny thing is that when i install 12.2(40)
> image everything works really ok ...while 12.2T or
> 12.3(22) it does not detect the serial card as well
> as it does not ping via the FE ports at all .
>
> could that be a ROMMON upgrade problem ? if that
> is the case ..where can i get the lastest rommon
> ..because it is not listed on cisco site .
>
> appreciate the help
>
>
>
> ---------------------------------
> Ahhh...imagining that irresistible "new car" smell?
> Check outnew cars at Yahoo! Autos.
>
>
This archive was generated by hypermail 2.1.4 : Tue May 01 2007 - 08:28:37 ART