From: Brian Dennis (bdennis@internetworkexpert.com)
Date: Sat Apr 21 2007 - 23:03:31 ART
Try this on all of the routers:
default interface X
interface X
shutdown
encapsulation ppp
do wr
Finally after this has been done on all of the routers in the FR network do
a "no shutdown" and add "encapsulation frame-relay" back to the interfaces.
--Brian Dennis, CCIE4 #2210 (R&S/ISP-Dial/Security/SP) bdennis@internetworkexpert.com Internetwork Expert, Inc. http://www.InternetworkExpert.com Toll Free: 877-224-8987 Direct: 775-745-6404 (Outside the US and Canada)
On 4/21/07 11:06 AM, "Todd, Douglas M." <DTODD@PARTNERS.ORG> wrote:
> UGH!!! This is driving me nuts.... > > Rack1R1(config)#default int s1/0 > Building configuration... > % Invalid input detected at '^' marker. > %Cannot remove PVC as being referenced by map statement > % Error(s) seen setting interface Serial1/0 to it's default config > Rack1R1(config)# > > pasted the config back on: > > in a 60 seconds the 0.0.0.0's come back again. > > NEXT: > Shut the interface: > removed the config > pasted the config > no sh the interface > they are back again... > > Even after a reload they come back. > > DMT > > > > > > > > -----Original Message----- > From: John Jones [mailto:acer0001@gmail.com] > Sent: Sat 4/21/2007 1:22 PM > To: Todd, Douglas M. > Cc: Victor Cappuccio; ccielab@groupstudy.com > Subject: Re: Frame-relay issues: > > Shut down the interface, change the encapsulation to another protocol, say > PPP, bring the interface up again. This should clear all mappings. Shut down > interface again and specify encap frame. Setup your fr maps again, save > to nvram, and then bring up the interface; your mapping should be correct. > If not, a reboot of the router is needed to remove the mappings to 0.0.0.0. > > HTH, > > John > > > On 4/21/07, Todd, Douglas M. <DTODD@partners.org> wrote: >> >> Thanks- >> >> I have already disabled inverse arp on the physical interfaces. Seems the >> router is still building a table for those DLCIs which are not used in >> this lab. >> I am getting ospf/pim adjs from routers which are in different networks >> even >> with inverse arp disabled on the physical interfaces. >> >> DMT >> >> >> >> -----Original Message----- >> From: Victor Cappuccio [mailto:victor@ccbootcamp.com] >> Sent: Sat 4/21/2007 10:45 AM >> To: Todd, Douglas M.; ccielab@groupstudy.com >> Subject: RE: Frame-relay issues: >> >> >> Good Point of reference >> >> http://www.groupstudy.com/archives/ccielab/200503/msg00398.html >> >> >> >> thanks, >> Victor Cappuccio.- >> Network Learning Inc - A Cisco Sponsored Organization (SO) YES! We take >> Cisco Learning credits! >> victor@ccbootcamp.com >> http://www.ccbootcamp.com (Cisco Training and Rental Racks) >> http://www.ccbootcamp.com/groupstudy.html (groupstudy member discounts!) >> Voice: 702-968-5100 >> FAX: 702-446-8012 >> >> >> >> >> -----Original Message----- >> From: nobody@groupstudy.com on behalf of Todd, Douglas M. >> Sent: Sat 4/21/2007 7:35 >> To: ccielab@groupstudy.com >> Subject: FW: Frame-relay issues: >> >> All: >> >> I am getting these bogus frame-relay maps on 2 routers. I have reloaded >> the >> router w/the interfaces shutdown with the configuration below. It's like >> frame-relay arp is "kind" of working when it's not enabled at all on the >> interface. >> >> Ideas? >> >> Thanks.. >> Rack1R1#sh run int s1/0 >> Building configuration... >> >> Current configuration : 321 bytes >> ! >> interface Serial1/0 >> ip address 136.1.15.1 255.255.255.0 >> ip pim sparse-dense-mode >> encapsulation frame-relay >> ip ospf authentication message-digest >> ip ospf message-digest-key 1 md5 CISCO >> ip ospf network point-to-point >> no arp frame-relay >> frame-relay map ip 136.1.15.5 105 broadcast >> no frame-relay inverse-arp >> end >> Rack1R1#sh frame-relay map >> Serial1/0 (up): ip 0.0.0.0 dlci 102(0x66,0x1860) >> broadcast, >> CISCO, status defined, active >> Serial1/0 (up): ip 0.0.0.0 dlci 103(0x67,0x1870) >> broadcast, >> CISCO, status defined, inactive >> Serial1/0 (up): ip 0.0.0.0 dlci 104(0x68,0x1880) >> broadcast, >> CISCO, status defined, active >> Serial1/0 (up): ip 136.1.15.5 dlci 105(0x69,0x1890), static, >> broadcast, >> CISCO, status defined, active >> Serial1/0 (up): ip 0.0.0.0 dlci 113(0x71,0x1C10) >> broadcast, >> CISCO, status defined, inactive >> Rack1R1# >> >> >> >> >> >> The information transmitted in this electronic communication is intended >> only >> for the person or entity to whom it is addressed and may contain >> confidential >> and/or privileged material. Any review, retransmission, dissemination or >> other >> use of or taking of any action in reliance upon this information by >> persons or >> entities other than the intended recipient is prohibited. If you received >> this >> information in error, please contact the Compliance HelpLine at >> 800-856-1983 and >> properly dispose of this information. >> >> >> >> >> >> >> >> The information transmitted in this electronic communication is intended >> only >> for the person or entity to whom it is addressed and may contain >> confidential >> and/or privileged material. Any review, retransmission, dissemination or >> other >> use of or taking of any action in reliance upon this information by >> persons or >> entities other than the intended recipient is prohibited. If you received >> this >> information in error, please contact the Compliance HelpLine at >> 800-856-1983 and >> properly dispose of this information. >> >> _______________________________________________________________________ >> Subscription information may be found at: >> http://www.groupstudy.com/list/CCIELab.html >> >> >> >> >> >> >> >> The information transmitted in this electronic communication is intended >> only for the person or entity to whom it is addressed and may contain >> confidential and/or privileged material. Any review, retransmission, >> dissemination or other use of or taking of any action in reliance upon this >> information by persons or entities other than the intended recipient is >> prohibited. If you received this information in error, please contact the >> Compliance HelpLine at 800-856-1983 and properly dispose of this >> information. >> >> _______________________________________________________________________ >> Subscription information may be found at: >> http://www.groupstudy.com/list/CCIELab.html >> > > > > > > > The information transmitted in this electronic communication is intended only > for the person or entity to whom it is addressed and may contain confidential > and/or privileged material. Any review, retransmission, dissemination or other > use of or taking of any action in reliance upon this information by persons or > entities other than the intended recipient is prohibited. If you received this > information in error, please contact the Compliance HelpLine at 800-856-1983 > and properly dispose of this information. > > _______________________________________________________________________ > Subscription information may be found at: > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Tue May 01 2007 - 08:28:36 ART