From: Darby Weaver (darbyweaver@yahoo.com)
Date: Wed Apr 04 2007 - 02:50:28 ART
Victor is one of those guys who does not actually have
to go to the lab to get his digits.
They actually seek him out to deliver them.
:)
--- Narbik Kocharians <narbikk@gmail.com> wrote:
> Victor i am proud of you, when are you going to take
> the R&S?
>
> On 4/3/07, ccie anees <ccieanees@yahoo.com> wrote:
> >
> > Correct. It is used to elect PIM DR. But I see in
> Doc CD,
> >
> >
>
http://www.cisco.com/en/US/products/ps6350/products_configuration_guide_chapt
> er09186a00805a4e8e.html#wp1054079
> >
> > Steps 3, 5, and 6 in this task are independent of
> each other and are
> > therefore considered optional. Any one of these
> steps will help optimize
> PIM
> > sparse mode. If you are going to perform Step 5 or
> 6, you must perform Step
> > 4. Step 6 applies only to a designated router;
> changing the PIM query
> > interval is only appropriate on redundant routers
> on the edge of the PIM
> > domain.
> > SUMMARY STEPS 1. enable
> > 2. configure terminal
> > 3. ip pim register-rate-limit rate
> > 4. ip pim spt-threshold {kbps | infinity}
> [group-list access-list]
> > 5. interface type number
> > 6. ip pim query-interval period [msec]
> >
> > Why do I need to configure spt-threshold in order
> to configure pim
> > query-interval?
> >
> > Thanks,
> >
> > Anees.
> >
> > Victor Cappuccio <victor@ccbootcamp.com> wrote:
> >
> > Hi,
> >
> >
> > Configures the frequency at which multicast
> routers send PIM router query
> > messages.
> > By default, multicast routers send PIM router
> query messages every 30
> > seconds. By enabling a router to send PIM hello
> messages more often, the
> > router can discover unresponsive neighbors more
> quickly. As a result, the
> > router can implement failover or recovery
> procedures more efficiently. It
> is
> > appropriate to make this change only on redundant
> routers on the edge of
> the
> > network
> >
> >
> > Perform this step only on redundant routers on
> the edge of a PIM domain.
> >
> > The default query interval is 30 seconds.
> >
> > The period argument is in seconds unless the msec
> keyword is specified.
> >
> > Set the query interval to a smaller number of
> seconds for faster
> > convergence, but keep in mind the trade-off
> between faster convergence and
> > higher CPU and bandwidth usage.
> >
> > thanks,
> > Victor Cappuccio.-
> > Network Learning Inc - A Cisco Sponsored
> Organization (SO) YES! We take
> > Cisco Learning credits!
> > victor@ccbootcamp.com
> > http://www.ccbootcamp.com (Cisco Training and
> Rental Racks)
> > http://www.ccbootcamp.com/groupstudy.html
> (groupstudy member discounts!)
> > Voice: 702-968-5100
> > FAX: 702-446-8012
> >
> >
> >
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com on behalf of ccie
> anees
> > Sent: Tue 4/3/2007 12:54
> > To: ccielab@groupstudy.com
> > Subject: PIM Query-interval
> >
> > Hi,
> >
> > What is PIM Query-interval? Is it to query the PIM
> Neighbor router? Is it
> > like PIM hello messages?
> >
> > And the doc cd says You need to enable ip pim
> spt-threshold <> in order to
> > configure ip pim query-interval <>? Is it true?
> >
> > Thanks,
> >
> > Anees.
> >
> >
> > ---------------------------------
> > Sucker-punch spam with award-winning protection.
> > Try the free Yahoo! Mail Beta.
> >
> >
>
This archive was generated by hypermail 2.1.4 : Tue May 01 2007 - 08:28:34 ART