From: Muhabat (muhabat@gmail.com)
Date: Sat Feb 24 2007 - 12:30:26 ART
Hi Ronnie,
Thanks for reply, as you said I have created VLAN 100 and It worked fine, I
have found an alternative, which is to first make switch client then let it
replicate the vlan database and then make it transparent, which is
essentially same as creating vlans manually.
Thanks for you help.
Best Regards,
_____
From: Ronnie Angello [mailto:ronnie.angello@gmail.com]
Sent: Saturday, February 24, 2007 6:15 PM
To: Muhabat
Cc: ccielab@groupstudy.com
Subject: Re: Vlan configuration Issue.
Make sure that VLAN100 exists on S2. You will need to configure it manually
since the switch is in transparent mode.
On 2/24/07, Muhabat <muhabat@gmail.com> wrote:
Hi GS,
I have created one configuration like this:
R1
S1---------------------S2------------------------------S3
Server Transparent Client
I have created Vlan 100, Vlan 200 and Vlan 300 on S1. After establishing
trunks between switches I found that vlans from S1 are propagating to S3
through (vtp transparent mode) S2.
s1#sh vtp status
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 256
Number of existing VLANs : 8
VTP Operating Mode : Server
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0xD9 0x56 0x10 0x46 0xCB 0xFF 0xF9 0x64
Configuration last modified by 0.0.0.0 at 3-1-02 00:17:34
Local updater ID is 192.168.100.100 on interface Vl100 (lowest numbered VLAN
interface found)
s2#sh vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 256
Number of existing VLANs : 5
VTP Operating Mode : Transparent
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x1A 0x89 0xC2 0x6C 0x8A 0x87 0xB5 0x9A
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
s3(config)#svs
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 256
Number of existing VLANs : 8
VTP Operating Mode : Client
VTP Domain Name : ExamUp.com
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0xD9 0x56 0x10 0x46 0xCB 0xFF 0xF9 0x64
Configuration last modified by 0.0.0.0 at 3-1-02 00:17:34
I put two interfaces in vlan 100 at s1 and s2, but they were unable to
communicate with each other, although both are in same vlan and interfaces
are configured for access mode.
S1
Port Name Status Vlan Duplex Speed Type
Fa1/0 connected trunk a-full 100
10/100BaseTX
Fa1/1 notconnect 1 auto auto
10/100BaseTX
Fa1/2 notconnect 1 auto auto
10/100BaseTX
Fa1/3 Interface for Vlan connected 100 a-full a-100
10/100BaseTX
S3
Port Name Status Vlan Duplex Speed Type
Fa1/0 notconnect 1 auto auto
10/100BaseTX
Fa1/1 connected trunk a-full 100
10/100BaseTX
Fa1/2 notconnect 1 auto auto
10/100BaseTX
Fa1/3 interface f1/3 - 6 connected 100 full 100
10/100BaseTX
Still I am not able to ping within the same vlan 100. Any help will be
highly appreciated.
Best Regards,
This archive was generated by hypermail 2.1.4 : Thu Mar 01 2007 - 07:38:48 ART