From: Victor Cappuccio (vcappuccio@gmail.com)
Date: Mon Feb 12 2007 - 00:23:31 ART
Mohamed,
Cisco has reported this as OSPF Bug ID: CSCse72792
"OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
networks"
*Symptom:*
Can't configure OSPF static neighbor
*Conditions:*
Virtual Link is configured.
*Workaround:*
There is no known workaround
HTH
Victor.-
> Tandou Mohamed wrote:
> > GS,
> > When I configured ip pim sparse-dense-mode under my interface i get
> this errors message below.
> >
> > interface config:
> >
> > "interface FastEthernet0/0
> > ip address 183.1.2.2 255.255.255.0
> > ip pim sparse-dense-mode
> > duplex auto
> > speed auto
> > no keepalive
> >
> > ================================================================
> > Errors message:
> >
> > Mar 7 09:06:15.440: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on
> this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 224
> > Rack1R2#
> > Mar 7 09:07:15.441: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on
> this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 224
> >
> > ===============================================================
> > i investigated the errors message according to cisco it says:
> > %MROUTE-3-NO_PIM_NBR : There is no PIM neighbor on this IDB: [chars]
> > Explanation There is no PIM neighbor on the specified IDB. The most
> probable cause of this error is that PIM is not configured correctly on this
> interface or on interfaces of the next-hop routers.
> >
> > ==============================================================
> > The lab said configure PIM on R2, R3 and R5. i don't get the error on
> R3 and R5 but only R2
> >
> > ==============================================================
> >
> > Task 3.2 requested to configure OSPF area 45 on VLAN 45 between R4 and
> R5 when i checked the solution they have:
> >
> > R4
> > interface FastEthernet0/0
> > ip address 183.1.45.4 255.255.255.0
> > ip ospf network non-broadcast
> >
> > router ospf 1
> > network 183.1.45.5 0.0.0.5 area 45
> > neighbor 183.1.45.5
> >
> > When i tried to simulate what they have i am getting this errors
> message:
> >
> > Rack1R4(config)#router ospf 1
> > Rack1R4(config-router)#nei
> > Rack1R4(config-router)#neighbor 183.1.45.5
> > OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> networks
> > Rack1R4(config-router)#
> >
> > i removed the ospf process and reapplied still getting the same error
> message
> >
> > Any idea?
> >
> > Thanks,
> > Mohamed
> >
> >
> >
> > ---------------------------------
> > Looking for earth-friendly autos?
> > Browse Top Cars by "Green Rating" at Yahoo! Autos' Green Center.
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Thu Mar 01 2007 - 07:38:46 ART