From: Bit Gossip (bit.gossip@chello.nl)
Date: Sun Jan 28 2007 - 17:07:57 ART
None shows the policy-map counter in the second setup: no counters per
class
Thanks,
Luca.
r2#show frame-relay pvc 221
PVC Statistics for interface Serial4/0 (Frame Relay DTE)
DLCI = 221, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE =
Serial4/0.221
input pkts 6988 output pkts 8069 in bytes 569861
out bytes 2186176 dropped pkts 1 in pkts dropped
1
out pkts dropped 0 out bytes dropped 0
in FECN pkts 0 in BECN pkts 0 out FECN pkts
0
out BECN pkts 0 in DE pkts 0 out DE pkts
0
out bcast pkts 6930 out bcast bytes 567024
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
pvc create time 08:17:05, last time pvc status changed 08:15:55
r2#show policy-ma
r2#show policy
r2#show policy-ma
r2#show policy-map int
r2#show policy-map interface s4/0
r2#
On Sun, 2007-01-28 at 12:51 -0500, Edison Ortiz wrote:
> There are 2 ways:
>
> 1) show frame pvc 221
>
> 2) show policy-map interface
>
> On 1/28/07, Bit Gossip <bit.gossip@chello.nl> wrote:
> My task requires to configure a certain service-policy to do
> policing
> and wfq between r2 and r1 which are connected via a fr pvc
> attached to a
> serial interface s4/0.221.
> I have found 2 approches; are they both correct?
> For the second one I dont know how to show and monitor the
> service-policy!
> BTW: it is not possible to attach the service-policy to the
> sub-if
> because wfq is not supported for sub-if
> Thanks,
> Luca.
>
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>
> - attach the policy to s4/0
>
> interface Serial4/0
> service-policy output S6
> ...
>
>
> in this case I can easily show the effect and monitor the
> counters:
>
>
> r2#show policy-map int s4/0
>
> Serial4/0
>
> Service-policy output: S6
>
> Class-map: S6-2 (match-all)
> 0 packets, 0 bytes
> 30 second offered rate 0 bps, drop rate 0 bps
> Match: access-group name S6-2
> police:
>
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>
> - attach the policy to dlci 221
>
> interface Serial4/0
> bandwidth 115200
> no ip address
> encapsulation frame-relay
> load-interval 30
> serial restart-delay 0
> no frame-relay inverse-arp
> !
> interface Serial4/0.221 point-to-point
> bandwidth 64
> ip address 10.1.122.2 255.255.255.0
> frame-relay interface-dlci 221
> class S6
>
> map-class frame-relay S6
> service-policy output S6
>
>
> But in this case I dont know how to monitor it?
> r2# show policy-map interface s4/0
>
> r2#
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Thu Feb 08 2007 - 23:46:57 ART