From: Keith Bizzell (mkbcoolman@gmail.com)
Date: Mon Jan 08 2007 - 13:33:18 ART
This section calls for creating a ppp link between R4/R5 using dialer
interfaces. This seems pretty straight-forward, and as far as I can tell my
config matches up with the solution guide. But it doesn't work. R4 never
shows an active call, and I never get an bind message. Interfaces show
up/up on both sides, and I know there isn't a problem with the link (it
works fine when I set up ppp on the physical interface.) Any ideas?
R4:
interface Serial0/1/0
no ip address
dialer in-band
dialer pool-member 1
pulse-time 1
!
interface Dialer0
ip address 128.1.45.4 255.255.255.0
encapsulation ppp
dialer pool 1
dialer idle-timeout 0
dialer persistent
!
Rack1R4(config-if)#do show ip int b
Interface IP-Address OK? Method Status
Protocol
FastEthernet0/0 128.1.14.4 YES NVRAM up
up
FastEthernet0/1 128.1.48.4 YES NVRAM up
up
Serial0/0/0 unassigned YES NVRAM administratively down
down
Serial0/1/0 unassigned YES NVRAM up
up
Dialer0 128.1.45.4 YES manual up
up
Loopback0 150.1.4.4 YES NVRAM up
up
Rack1R4(config-if)#do show dialer
Se0/1/0 - dialer type = IN-BAND SYNC NO-PARITY
Dialer pool 1, priority 0
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
Di0 - dialer type = DIALER PROFILE
Idle timer (never), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is idle
Number of active calls = 0
Dial String Successes Failures Last DNIS Last status
R5:
interface Serial0/1/0
no ip address
dialer in-band
dialer pool-member 1
clock rate 64000
pulse-time 1
!
interface Virtual-Template1
ip address 128.1.125.5 255.255.255.0
!
interface Dialer0
ip address 128.1.45.5 255.255.255.0
encapsulation ppp
dialer pool 1
dialer idle-timeout 0
dialer persistent
!
Rack1R5(config-if)#do show dialer
Se0/1/0 - dialer type = IN-BAND SYNC NO-PARITY
Dialer pool 1, priority 0
Idle timer (never), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is data link layer up
Interface bound to profile Di0
Time until disconnect never
Connected to <unknown phone number>
Di0 - dialer type = DIALER PROFILE
Idle timer (never), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is data link layer up
Number of active calls = 1
Dial String Successes Failures Last DNIS Last status
Rack1R5(config-if)#do show ip int b
Interface IP-Address OK? Method Status
Protocol
FastEthernet0/0 unassigned YES unset administratively down
down
FastEthernet0/1 128.1.5.5 YES manual up
up
Serial0/0/0 unassigned YES unset up
up
Serial0/0/0.1 unassigned YES unset up
up
Serial0/1/0 unassigned YES TFTP up
up
Virtual-Access1 unassigned YES unset down
down
Virtual-Template1 128.1.125.5 YES manual down
down
Virtual-Access2 128.1.125.5 YES TFTP up
up
Virtual-Access3 128.1.125.5 YES TFTP up
up
Dialer0 128.1.45.5 YES manual up
up
Loopback0 150.1.5.5 YES manual up
up
This archive was generated by hypermail 2.1.4 : Thu Feb 08 2007 - 23:46:56 ART