From: Guyler, Rik (rguyler@shp-dayton.org)
Date: Wed Dec 20 2006 - 14:05:16 ART
I would have thought so too before trying it "first-hand". Last year when
upgrading my 7200s I fat fingered the the boot config on one of them and it
still came up but on the old code, which I left in flash just in case.
Could be platform specific I guess.
Rik
-----Original Message-----
From: Darby Weaver [mailto:darbyweaver@yahoo.com]
Sent: Tuesday, December 19, 2006 11:38 PM
To: Guyler, Rik; ccielab@groupstudy.com
Subject: RE: Router Boot
I've had that experience if I had nothing specified as boot source.
However, when I specify the wrong name, then I end up in Rommon.
I'm speaking from the top of my head, but that's what I think happens every
single time.
I have not systematically validated it though. Might be an interesting
exercise - just so it never comes up again in any way ambiguous.
However, I'm pretty sure my results are the same every time.
--- "Guyler, Rik" <rguyler@shp-dayton.org> wrote:
> Ian, my experience with boot statements is that if you enter it
> incorrectly or configure it for a non-existing image, the device will
> boot up any image it finds then in the filesystem, whether or not it's
> defined in a boot statement. Have you had different experiences?
>
> Rik
>
> -----Original Message-----
> From: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com] On Behalf Of istong@stong.org
> Sent: Monday, December 18, 2006 2:28 PM
> To: Tandou Mohamed; eiko Liedtke
> Cc: Tandou Mohamed; ccielab@groupstudy.com
> Subject: Re: Router Boot
>
> Hi,
>
> Any number of things can cause your router to boot into rommon mode.
> Several have been mentioned such as a
> config-register setting or invalid
> boot command setting...
> Corruption of the image on the flash is another why the router would
> boot into rommon mode. Other things that come to mind are an image
> that is too large to run with the amount of memory you have so the
> router can't boot up from flash. Another thought is the bootrom could
> be too old in relation to the ram/flash/image you have. Just some
> things to think about and check.
>
>
> Thanks,
>
> Ian
> www.ccie4u.com
>
>
>
> > Thanks everyone, i checked the register is set to
> 0x2102
> > Don't why anytime i reboot it goes into rommon.
> >
> > Mohamed
> >
> > Ronnie Angello <ronnie.angello@gmail.com> wrote:
> > Mohamed,
> >
> > Try checking the config register.
> >
> >
>
http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186
> a008022493f.shtml
> >
> > Ronnie
> >
> >
> > On 12/17/06, Heiko Liedtke wrote:
> > >
> > > Mohamed,
> > >
> > > please check that your IOS is the first file on
> your flash card. If
> > > there is no boot system command configured, the
> router will always
> > > try to load the first
> > file in flash; even it is a myconfig.cfg file ;-)
> >
> > > Maybe you can try to start the IOS directly from
> rommon mode and
> > > than check your file system and configure a boot
> system command if
> > > neccessary
> > >
> > > Heiko
> > >
> > >
> > > Tandou Mohamed schrieb:
> > >
> > > >Hello GS,
> > > > anytime my router boot it goes into rommon. i
> have to
> > > use tftpdnld to restore the IOS. can someone
> tell me what do i need
> > > to do to stop it going into rommon? do i need a
> new flash? the one
> > > in the router is going bad?
> > > Please advise >
> > > > Thanks,
> > > >
> > > > Mohamed
>
>
>
>
> _________________________________________
>
> Check your Email accounts at MyEmail.com
>
> Login from home, work, school. Anywhere!
>
>
This archive was generated by hypermail 2.1.4 : Tue Jan 02 2007 - 07:50:38 ART