From: Josef A (josefnet@gmail.com)
Date: Sat Dec 09 2006 - 12:41:06 ART
Deji,
I am not sure you can get the higher version of that code for your router
platform on cisco.com. But you can try a 12.2(T) version, and boot boot
directly from tftp into RAM:
rommon 1 > tftpdnld -r
IP_ADDRESS: 192.168.1.6
IP_SUBNET_MASK: 255.255.255.0
DEFAULT_GATEWAY: 192.168.1.1
TFTP_SERVER: 192.168.1.2
TFTP_FILE: c2600-js-mz.122-15.T14.bin
Rack1R2(config-if)#ipv6 ospf ?
<1-65535> Process ID
cost Interface cost
database-filter Filter OSPF LSA during synchronization and flooding
dead-interval Interval after which a neighbor is declared dead
demand-circuit OSPF demand circuit
flood-reduction OSPF Flood Reduction
hello-interval Time between HELLO packets
mtu-ignore Ignores the MTU in DBD packets
neighbor OSPF neighbor
network Network type
priority Router priority
retransmit-interval Time between retransmitting lost link state
advertisements
transmit-delay Link state transmit delay
Rack1R2#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-JS-M), Version 12.2(15)T14, RELEASE SOFTWARE
(fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Sat 28-Aug-04 06:48 by cmong
Image text-base: 0x80008098, data-base: 0x81D1B400
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-JS-M), Version 12.2(15)T14, RELEASE SOFTWARE
(fc4)
Rack1R2 uptime is 1 minute
System returned to ROM by reload
Running default software
cisco 2610 (MPC860) processor (revision 0x203) with 61440K/4096K bytes of
memory.
Processor board ID JAD05069A4Q (376511811)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
1 Ethernet/IEEE 802.3 interface(s)
4 Low-speed serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Thanks
Josef
On 12/9/06, deji500@hotmail.com <deji500@hotmail.com> wrote:
>
> Hi Group,
>
> I am having the following problem on my routers (2610)
> Rack1R4(config)#ipv6 router ospf 1
> Rack1R4(config)#int e0/0
> Rack1R4(config-if)#ipv6 ospf ?
> % Unrecognized command
> Rack1R4(config-if)#ipv6 ospf
>
> This is the ios on my routers:
> System image file is "flash:c2600-j1s3-mz.123-15b.bin"
>
> I am almost certain it is an IOS issue. Does anyone know if and how i can
> get a higher version of the ios. I have tried Cisco but there is no higher
> version there.
>
> I would be very greatful for any suggestions.
> Thanks
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Tue Jan 02 2007 - 07:50:37 ART